Mathematical and experimental investigation of the self-propagating high-temperature synthesis (SHS) of TiAl3 and Ni3Al intermetallic compounds

One-dimensional mathematical modeling was used to describe the self-propagating high-temperature synthesis (SHS) process for preparing TiAl₃ and Ni₃Al intermetallics. The kinetic parameters (activation energies and pre-exponential factors) for the two compounds were obtained by matching experimental measurement and the numerical solution. The results thus obtained were compared with rate parameters obtained using different methods. The activation energy was 483 and 283 kJ mol^?1 for the formation of TiAl₃ and Ni₃Al, respectively. The temperature profiles calculated using the mathematical model were compared with experimental measurements for both aluminides which indicated reasonable agreement. Fine particle size and moderate preheating increase the SHS rates.     

Growth of Fe on Si (100) at room temperature and formation of iron silicide

Low-energy electron diffraction (LEED), Auger electron spectroscopy and X-ray photoelectron spectroscopy (XPS) investigations of both the growth of an iron film on silicon (100) at room temperature and the subsequent formation of iron silicide are the subjects of this paper. An in-situ cleaned silicon (100) wafer without carbon or oxygen contamination exhibiting the known 2 × 1 reconstruction in the LEED pattern served as the substrate. Iron was deposited on this reconstructed surface at 300 K. The comparison of theoretical calculations based on three growth mechanisms with XPS data obtained with take-off angles of 0° and 50° clearly demonstrates a layer-by-layer growth of the iron film on silicon (100). At 300 K no formation of iron silicide was observed, although an interaction between iron and silicon could be detected at the interface. The formation of iron silicide was observed at annealing temperatures of 630–730 K. Quantitative XPS analysis yields the presence of FeSi₂, when the thickness is large enough. Neither the iron film on silicon nor the silicide shows any LEED pattern.     

Analysis of composite laminates with transverse cracks

The analysis of the behaviour of composite laminates with general balanced lay-up sequences and containing distributed transverse cracks is discussed and demonstrated in this paper. It is shown that a constitutive model of damage for composites, which has been successfully used to analyse the effects of uniformly distributed transverse cracks in cross-ply laminates, can be readily extended to the analysis of uniformly distributed transverse cracks in more general symmetric laminates. The further extension of the theory to non-uniformly distributed damage can be achieved by finite element analysis. It is shown that the finite element implementation of the theory is particularly simple since the contribution of the damage to the overall behaviour can be incorporated into the force vectors.     

A single-chip 12.7 Mchips/s digital IF BPSK direct sequencespread-spectrum transceiver in 1.2 μm CMOS

This paper describes a fully integrated digital-spread spectrum transceiver chip fabricated through MOSIS in 1.2 μm CMOS. It includes a baseband spread spectrum transmitter and a coherent intermediate frequency (IF) receiver consisting of a Costas loop, an acquisition loop for the pseudo-noise (PN) sequence, and a clock recovery loop with a 406.4 MHz onchip numerically controlled oscillator (NCO). The transceiver is capable of operating at a maximum IF sampling rate of 50.8 MS/s and a maximum chip rate of 12.7 R Mchips/s (Mcps) with selectable data rates of 100, 200, 400, and 800 kbps. At the maximum operating speed of 50.8 R MS/s, it dissipates 1.1 W. In an additive white Gaussian noise channel the IF receiver achieves a receiver output SNR within 1 dB of theory and can acquire code with a wide range of input SNR from -17 dB to over 30 dB. The transceiver chip has been interfaced to an RF up/down converter to demonstrate a wireless voice/data/video link operating in the 902-928 MHz band     

Design of FIR linear phase filters with discrete coefficients usingHopfield neural networks

A novel method is presented for designing FIR linear phase filters with discrete coefficients using Hopfield neural networks. The proposed procedure is based on the minimisation of the energy function of the Hopfield neural network, and can produce a good solution to the design of FIR linear phase filters with discrete coefficients     

Case performed: simultaneous surgery for left coronary ostial stenosis and gastric cancer

This report describes a case in which a 68-year-old male underwent two operations simultaneously for left coronary ostial stenosis and gastric cancer. Successfully performed procedures were a single coronary artery grafting with the saphenous vein to the left anterior descending artery, and a subtotal gastrectomy using the Billroth II method. The postoperative course was uneventful and the patient was discharged from the hospital in good condition after 42 days. At present, one-year postoperative, the patient has been visiting the outpatient clinic in healthy condition.     

Visual functions after photorefractive keratectomy

1. 45 myopes (-3.0 to -6.0 D) were examined before and 1 and 6 months after photorefractive keratectomy (PRK). Visual acuity (VA) was tested using Snellen and logMAR charts. Contrast sensitivity (CS) was measured using a computerized system. 2. Preoperative best corrected VA (BCVA) in myopes was significantly lower in comparison with a control group using logMAR charts only. A reduction of BCVA by both methods at 1. month and its return after 6 months nearly to original values was noted. 3. Significantly lower values of CS were found in patients before PRK compared to the control group. After 1 and 6 months stayed the values on preoperative level.     

Analysis of integrated optical waveguide mirrors

A new method is presented to analyze reflection losses of integrated mirrors, taking into account the exact guided mode profile and assuming that this profile remains unchanged up to the reflecting plane. The fraction of the reflected light coupled to one of the guided modes of the output waveguide is calculated, taking into account the mirror reflection coefficient. The influence of both translation and tilt of the reflecting plane is investigated. The method applies for every guided mode and any reflection angles. Numerical calculations are derived for a 90° optical corner mirror