基于FPGA的MEMS陀螺仪SAR150实时数据采集系统设计

针对传统MEMS陀螺仪输出信息为模拟量且易受干扰、噪声较大的问题,结合SAR150陀螺仪可以直接输出数字信号的特点,提出了一种新型的数字陀螺仪实时数据采集系统;该系统以FPGA为主控制器,通过SPI接口完成对MEMS陀螺仪SAR150的控制与数据的传输,实现了对陀螺仪输出信号的采集、实时传输及存储;通过将所研制的数据采集系统应用于SAR150陀螺仪测量角速率实验,并对测得数据进行误差分析,实验结果表明:数据采集系统采集输出的角速率值与理论值的绝对误差标准差均小于0.2°/s;且该系统的可靠性高、实时性好,为后续的陀螺仪测试及标定奠定了基础,有一定的工程应用价值。     

A technique for assessment of torso kinesiology

A technique is described for monitoring and analysis of the angular displacement of the human torso. The technique is based on the use of miniature electromechanical inclinometers and video recording. The system was developed for continuous measurement of the angular displacement of spinal segments in the sagittal plane during all stages of lifting. Angular displacements of the cervical, thoracic and lumbar regions were obtained from a dynamic lifting case study using a digital processing system. The geometrical changes of the torso during five prescribed stages were measured. The system revealed good accuracy with high correlation coefficient scores for a wide range of lifting tasks in a comparative laboratory study. This paper describes the monitoring technique; the system's advantages, disadvantages and measuring accuracy are discussed.     

The minimum quantity of nitrite required to stain sliced and homogenised cooked pork

The levels of nitrite used in curing pork are in excess of those required to produce an adequate cured colour, but the minimum level for pink coloration to be visible has not been established experimentally. This paper demonstrates the effect of low nitrite levels from local surface application to pork muscle, simulating inadvertent contamination from work surfaces. An homogenate is used for comparison in which the nitrite was evenly distributed throughout the product. The results indicate that surface contact with nitrite produces essentially the same pattern of colour change as in the homogenate. Visible pink coloration was evident from 1-2 mg kg(-1) sodium nitrite absorbed.     

TiO2/MOFs的制备及污染物降解现状

TiO2是较为成熟的半导体光催化材料,但因TiO2分散性差、量子利用率低、比表面积小、难回收等问题难以工业化.多孔金属有机框架(MOFs)的引入可增强TiO2/MOFs复合材料的光吸收性能,提高电子-空穴对分离效率和提高回收率.基于TiO2/MOFs制备时前驱体添加顺序不同,综述了TiO2/MOFs的3种制备方法(即Ship-in-a-bottle法、Bottle-around-ship法、One-pot法)及TiO2/MOFs光催化机理与性能影响因素,并探讨不同MOFs与TiO2结合的作用机理.最后,对TiO2/MOFs存在的问题提出建议.     

热处理工艺对BT9合金疲劳和高温持久性能的影响

本文研究了不同的热处理工艺对BT9钛合金的疲劳寿命和高温持久强度的影响,并对其组织、断口进行了光学和电子金相分析。指出了获得良好的综合机械性能的热处理工艺,并讨论了在不同区域内疲劳裂纹扩展的方式。     

Effect of ultrasonic power and bonding force on the bonding strength of copper ball bonds

Copper wire, serving as a cost-saving alternative to gold wire, has been used in many high-end thermosonic ball bonding applications. In this paper, the bond shear force, bond shear strength, and the ball bond diameter are adopted to evaluate the bonding quality. It is concluded that the ef/~cient ultrasonic power is needed to soften the ball to form the copper bonds with high bonding strength. However, excessive ultrasonic power would serve as a fatigue loading to weaken the bonding. Excessive or less bonding force would cause cratering in the silicon.     

Synthesis of LaF3 superfine powder by microwave heating method

LaF3 superfine powder was synthesized from La(CH3COO)3 and NH4 F by microwave heating method,using ethanol or pure water as dispersants respectively. The results of XRD and SEM indicate that the superfine powder has high purity, regular particle shape and narrow distribution of granularity. The granularity of the best sample is in the range of 100 -200 nm. The influence of different dispersants on the crystal degree and microstructure was discussed. After the superfine powder was formed into a slice at pressure of 25 - 60 MPa, its electrochemical impedance spectroscopy was tested by electrochemical impedance spectroscopy (EIS) measurement. The result shows that the grain refining of LaF3 powder increases its ionic conductivity. Compared with traditional preparation methods of LaF3 powder, the advantages of microwave heating method were summarized.     

34CrNiMo钢齿轮轴开裂原因分析

对34CrNiMo钢齿轮轴的化学成分、金相组织及断口分析表明，其淬火开裂的主要原因是由于锻造温度过高，导致过热缺陷所致。     

铝合金钢盐浴硫氮碳在层中合金元素的分布及组织特征

对３８ＣｒＭｏＡｌ，４２ＣｒＭｏ和Ｗ６Ｍｏ５Ｃｒ４Ｖ２Ａｌ合金钢盐浴硫氮碳共渗层的组织进行了研究表明：３８ＣｒＭｏＡｌ和Ｗ６Ｍｏ６Ｃｒ４Ｖ２Ａｌ钢的共渗层中，白亮层和过渡层的交界处有沿一定晶面析出的大量针状氮化物和沿晶界析的网状氧化物，它们导致白亮层中出现１００μｍ左右的裂纹。