Segregation of Isovalent Impurity Cations at the Surfaces of MgO and CaO

Enthalpies of segregation for isovalent impurities in magnesium and calcium oxide as a function of surface concentration were calculated by using an atomistic computer simulation method. We have considered Be²⁺, Mg²⁺, Ca²⁺, Ba²⁺, and Ni²⁺, segregating to both (001) and (110) faces. The results obtained can be extrapolated to predict the behavior of other impurities including Mn²⁺, Fe²⁺, and Co²⁺, We find, for example, that Fe²⁺, Mn²⁺, Ca²⁺, Sr²⁺, and Ba²⁺ will concentrate at the (001) surface of MgO, while Ni²⁺ will be depleted. The enthalpy of segregation is found to vary substantially with coverage particularly for the larger impurities. The enthalpy becomes less negative with increasing impurity concentration due to the increasing lattice strain until the surface is nearly saturated. Then additional stabilization is obtained by restructuring of the surface layer. We predict reconstructed surfaces for both the (001) and (110) faces, which contain a high concentration of a larger impurity ion. The enthalpy of segregation shows a maximum at around 50% surface coverage implying a bimodal surface distribution of segregant. The influence of segregation on surface energy suggests two unusual effects. The (001) surface energy of the impure crystal becomes negative for surface concentrations of impurity greater than 10% Ba²⁺ or 75% Sr²⁺ in MgO. This implies a thermodynamic barrier to sintering. At high coverages of Ba²⁺ in MgO the (110) surface becomes more stable than the (001) face suggesting that facetting may occur.     

Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.     

An experiment for showing some kind of artificial understanding

In this paper we design an experiment which can be depicted as a simple scenario, a very limited 'world'. In this world, there are an actor that can pursue a project and an observer that is keeping its eyes on the actor. We try to show in the experiment that the observer can to some degree understand the actor based on its knowledge and some metaphors, i.e. understand what the actor is doing and why. As the conclusion of this experiment, we try to show some features of 'understanding'. These are (1) that 'understanding' has to be based on some preliminary knowledge; (2) that 'understanding' is a process of incremental learning; (3) that, as for symbolic systems, some metaphors are necessary for mapping real entities into concepts in mind.     

Ozone measurement in visible region: an optical fibre sensor system

Ozone measurement based on the optical absorption of visible light at 603 nm using polymer optical fibres is investigated and tested. Comparisons with a commercial UV based sensor demonstrate the ability of the visible based sensor to measure high concentrations over a range 27-127 mg/litre. A resolution of 5 mg/litre is also demonstrated for this sensor.     

Standing on Solid Ground

The new Editor in Chief of IEEE Micro introduces himself and the first issue of 2007. He thanks outgoing Editor in Chief Pradip Bose for his outstanding work on Micro during his tenure. He assesses the current state of the microarchitecture field, speculates on the future, and asks readers for their suggestions on topics the magazine should cover in coming issues.     

3D design tools speed NASA space shuttle work

There will always be a premium on innovation and original approaches to old problems. Engineers and designers are constantly urged to think outside the box. In space shuttle technician Arlene S. Reese's case, she decided to think outside the world of traditional, 2D drafting. Working under tough deadline pressures for a shuttle lighting installation project, Reese and her design team decided to blend digital photographs and 3D assemblies to show other contractors precisely where and how the job should be built. The result was a faster, more effective method for planning electrical projects that has earned awards for her team and continues to produce benefits for the National Aeronautics and Space Administration (NASA). Reese and the managers at NASA say the design method can apply to many architectural and engineering disciplines.     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.