Effect of Channel Changes in the St. Clair River During the Present Century

Periodic man-made changes in the outlet of Lake Huron through the St. Clair River date back to the middle of the last century. These artificial channel changes have been well documented during the present century. They consist of dredging for commercial gravel removal in the upper river during 1908–25 and uncompensated navigation improvements for the 7.6-m (25-ft) and 8.2-m (27-ft) projects completed in 1933 and 1962, respectively. The total effect of these changes on the levels of Lakes Michigan and Huron (hydraulically one lake) and on the upper St. Clair River profile was determined with dynamic flow models. The ultimate effect of the above dredging was a permanent lowering of the Lake Michigan-Huron levels 0.27 m (0.89 ft), which represents a tremendous loss of freshwater resource [32 km³ (7.7 mi³)].     

A Study of Ozone Generation by Negative Corona Discharge Through Different Plasma Chemistry Models

The Steady radial distribution of chemical species in a wire‐to‐cylinder ozone generator filled with pure oxygen has been computed by applying four different plasma chemistry models of increasing complexity. The most complete model considers ten species (e, O₂ ⁺, O₂ ^?, O₃ ^?, O^?, O₂, O₂(¹Δ_g), O₂(¹∑_g ⁺), O and O₃) and 79 reactions, including ionization by electron impact, electron attachment and detachment, electron-ion recombination, charge transfer, etc. The chemical model is coupled with the electrical model through Poisson's equation. The spatially averaged ozone density has been computed as a function of the current intensity and compared with the experimental values obtained by UV spectroscopy.     

Microcalorimetry for characterization of film formation and cure of coatings and adhesives

A new microcalorimeter with eight parallel channels using robust, low cost sensors for characterization of coatings and adhesives is described and first experiments on coatings and adhesives are presented. The calorimetric sensors are based on thin glass plates (20 mm × 20 mm, thickness 150 μm) with heater and thermocouple sputtered on the surfaces (calorimetric active area of about 9 mm²). The setup allows heating and cooling experiments as well as isothermal measurements in the temperature-modulated mode with up to eight sensors in parallel. The measured quantities are the real (C^′_p) and imaginary part (C^″_p) of the complex heat capacity (), the related absolute value of the heat capacity () and the heat flow . An industrial computer (NI PXI system) with specific software for calibration and data recording controls the electronic components. Sensors can be embedded in a temperature controlled oven (heating and cooling by Peltier elements) or alternatively in a climatic cabinet with controlled temperature and humidity.

The method has been applied successfully to monitoring of film formation of aqueous polymer dispersions (styrene-acrylate copolymer) and curing of coatings.     

Societal Safety: Concept,Borders and Dilemmas

In most industrialized countries, the end of the Cold War marked a change in focus from preparedness for war to an increasing focus on civil society's own vulnerability and safety. To meet new threats and changing risks, there is also a need for new analytical concepts. Societal safety is a concept developed in Norway during the last decade. It could be defined as: ‘The society's ability to maintain critical social functions, to protect the life and health of the citizens and to meet the citizens' basic requirements in a variety of stress situations’. It aims to be a systematic approach for understanding, mitigating and responding to social problems such as extraordinary stresses and losses, interferences in complex and mutual dependent systems, or lack of trust in vital social institutions. Future threats to society are not limited to specific sectors or areas, but stem from complex interactions amongst economic, technological, social and cultural factors. Thus, the main challenges to improve societal safety will be the ability to coordinate, organize and assign clear roles to different actors at the international, national and local levels. Societal safety has interfaces with other safety‐related areas such as national security, sustainable development, human security and incident management (handling of isolated accidents, common illness and ordinary criminal acts). Societal safety is, however, a sensitive political issue containing dilemmas and value choices that are hardly possible to perceive or solve as pure scientific problems.     

Shear mode coupling and tilted grain growth of A1N thin films in BAW resonators.

Polycrystalline A1N thin films were deposited by RF reactive magnetron sputtering on Pt(111)/Ti electrode films. The substrates were tilted by an angle ranging from 40 degrees to 70 degrees with respect to the target normal. A low deposition temperature and a high sputter gas pressure were found ideal for tilted growth. The resulting grain tilt angle amounts to about half the substrate tilt angle. For coupling evaluation, 5 GHz solidly mounted resonator structures have been realized. The tilted grain A1N films exhibited a permittivity in the 9.5-10.5 range and loss tangent of 0.3%. Two shear modes as well as the longitudinal mode could be clearly identified. The coupling coefficient k2(eff) of the fundamental thickness shear mode (TS0) was found to be about 0.5%, which is compatible with a c-axis tilt of about 6 degrees.     

Interfacial activity and rate of palladium(II) extraction with decyl pyridine monocarboxylates

Decyl isonicotiniate and decyl nicotiniate permit a rapid extraction of palladium(II) from its hydrochloride solutions. Decyl picoliniate is not a suitable extractant. 4-Octylphenylamine can act as a phase transfer catalyst when its concentration in the organic phase is at least 2·5 × 10^?4 M . It seems that the interfacial adsorption of pyridine carboxylates and of 4-octylphenylamine is not the decisive phenomenon in palladium(II) extraction. The negligible protonation of the pyridine-type extractants and the phase transfer catalysis explains well the quick extraction of palladium(II) with the commercial and highly hydrophobic extractant ACORGA CLX-50.     

Nature-Inspired Meta-Heuristics on Modern GPUs: State of the Art and Brief Survey of Selected Algorithms

Graphic processing units (GPUs) emerged recently as an exciting new hardware environment for a truly parallel implementation and execution of Nature and Bio-inspired Algorithms with excellent price-to-power ratio. In contrast to common multicore CPUs that contain up to tens of independent cores, the GPUs represent a massively parallel single-instruction multiple-data devices that can nowadays reach peak performance of hundreds and thousands of giga floating-point operations per second. Nature and Bio-inspired Algorithms implement parallel optimization strategies in which a single candidate solution, a group of candidate solutions (population), or multiple populations seek for optimal solution or set of solutions of given problem. Genetic algorithms (GA) constitute a family of traditional and very well-known nature-inspired populational meta-heuristic algorithms that have proved its usefulness on a plethora of tasks through the years. Differential evolution (DE) is another efficient populational meta-heuristic algorithm for real-parameter optimization. Particle swarm optimization (PSO) can be seen as nature-inspired multiagent method in which the interaction of simple independent agents yields intelligent collective behavior. Simulated annealing (SA) is global optimization algorithm which combines statistical mechanics and combinatorial optimization with inspiration in metallurgy. This survey provides a brief overview of the latest state-of-the-art research on the design, implementation, and applications of parallel GA, DE, PSO, and SA-based methods on the GPUs.     

Development of high‐definition aqueous polyvinylpyrrolidone photoresists for cathode ray tubes

Aqueous photoresists that are capable of higher resolutions than are currently employed by the cathode ray tube (CRT) industry were developed by combining photoactivators, which activate at shorter UV wavelengths with polyvinylpyrrolidone (PVP). Two photoactivators were synthesized: 4,4′‐diazido‐2,2′‐biphenyl disodium disulfonate (DABP), which has a maximum absorbance at 264 nm, and 4,4′‐diazido‐2,2′‐biphenylethane disodium disulfonate (DABPE), which has a maximum absorbance at 258 nm. The PVP/DABP and PVP/DABPE photoresists successfully imaged a pattern with resolution as small as 4.4 μm with photoactivator concentrations greater than 20% of the PVP concentration. Addition of silane and emulgen greatly improved the performance of the photoresists with more uniform coatings of thicknesses of up to 1.4 μm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1637–1644, 2006