Design aspects of planar and conventional SMPS transformer: a cost benefit analysis

The intent of this paper is to design a high-frequency transformer that is to be incorporated into the DC/DC pulsewidth-modulated switch-mode power supplies by two different technical approaches: a conventional wound-coil magnetic using copper wires, and a planar magnetic with layered copper tracks on laminated printed circuit board. Comparisons will be made between the two approaches in terms of profile: mounting height and surface area, and performance: power losses and efficiency. Other indicators like temperature rise and leakage inductance that causes electromagnetic interference, and cost, materials, and process fluency are also to be looked into. A sandwiched configuration for primary and secondary windings is proposed for the planar type. Issues arising and typical phenomena encountered will be discussed in detail. Primarily, the dominating factor in performance, cost effectiveness, or circuit compactness that restrains the choice of a particular type is to be evaluated.     

The prospects of non-volatile phase-change RAM

Phase-change read-and-write memory (PRAM) is a promising memory that can solve the problems of conventional memory—scalability, read/write speed, and reliability. We will review the opportunities and technical challenges of PRAM. The most important challenge of PRAM is the reduction of the writing current. Various approaches to reduce the writing current will be reviewed and the prospects of PRAM are discussed.     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

Nickel and chromium cycles: Stocks and flows project part IV

Nickel and chromium are essential ingredients in alloys increasingly important for energy-efficient, environmentally friendly modern technology. Quantitative assessment of the flows of these metals through the world economy from resource extraction to final disposal informs resource policy, energy planning, environmental science, and waste management. This article summarizes the worldwide technological cycles of nickel and chromium in 2000. Stainless steel is the major use of these metals, but they serve numerous other special needs, as in superalloys for high-temperature service, as plating materials, and in coinage. Because they are used primarily in alloys, novel recycling issues arise as their use becomes more widespread. “... the great New York and St. Louis double track, nickel plated railroad...” — Norwalk, Ohio, Chronicle 10 March 1881 announces arrival of surveyors for the future Nickel Plate Railway “Later [1911] I formed an alloy of Iron and Chromium, which showed remarkable resistance to rust and tarnish ... [It was] rediscovered by an Englishman named Brearley, in 1914.” —Elwood Haynes to Stephen F. Roberts, 17 January 1925     

Influence of the silicon surface treatment by plasma etching and scratching on the nucleation of diamond grown in HFCVD - a comparative study

A comparative study for the nucleation of diamond was carried out using surface treatment like (i) surface scratching with 1 μm diamond paste and (ii) surface etching using chlorine plasma at different RF powers (50, 100 and 150 W). Atomic force microscopic study shows variation in roughness from 31 nm to 110 nm. Scratching results in random scratches, whereas plasma etches a surface uniformly. Scanning electron microscopic observations show well faceted crystallites with a predominance of angular shaped grains corresponding to 〈100〉 and 〈110〉 crystallite surfaces for the scratched as well as plasma etched substrate. Surface etching at 150 W plasma power results in a better growth in comparison with 50 and 100 W plasma powers. Chlorine-radical is found responsible for the changes in the growth morphology. Raman spectroscopy shows a sharp peak at 1,332 cm⁻¹ and a peak at ∼1,580 cm⁻¹ for both samples.