Dynamic laser control using feedback from a gain grating

We demonstrate that self-induced gain gratings can provide nonlinear optical feedback that results in single frequency selection and passive self Q-switching of a conventional linear laser cavity. An experimental Nd:YAG laser system is described that yields a temporally-smooth 20 ns pulse at 1.064 μm. In addition, we show that the feedback has phase-conjugate properties that permit “flower-like” mode formation even though the azimuthal symmetry of the cavity is broken     

含多孔物质硝胺发射药的温感特性

研究了多孔物质对于硝胺发射药在不同初温下的燃面调节作用，由于多孔物质的孔结构及其与基体界面状况的改变，使发射药低温燃面增大，而高温燃面减小，这有利于降低燃速温度系数．     

工业汽轮机的清洗

本文介绍了用饱和蒸汽对冷凝式汽轮机进行清洗除垢时主要参数的确定、操作要点及清洗方案，清洗后的汽轮机运行正常。     

纳米复合材料——石墨层间化合物(GICs)的结构分析

本文调研了纳米复合材料——GICs(石墨层间化合物)结构的主要研究方法、原理及模型,并介绍了在GICs结构研究中用到的现代分析手段。     

目标机动规范模型研究

分析和总结了飞机各种机动动作的内在因素,提出了目标机动规范模型,研究了模型的数学描述方式、控制参量的相互约束关系及其组织形式,并通过模拟导弹对目标的攻击过程对模型进行了验证。     

Medical imaging research on idiopathic hemifacial spasm

In order to have a medical imaging examination for idiopathic hemifacial spasm before surgery, we designed a new method by using vertebroarterial DSA and vertebroarterial CTA based on an aired cisternapontis, 36 patients were examined since 1989 and the compression of the facial nerve from brain stem to porus acousticus internus was showed clearly in all the cases. The arteries responsible for the compression were cerebellar inferior posterior (55.6%), cerebellar inferior anterior (44.4%), auditory internus (25.0%) and vertebroarterial (11.1%), 36% of all the cases had more than one responsible arteries, 22.2% cases had only one compression point, 38.9% had two points, 25.0% had 3 and 13.9% had more. 85.7% of the compression points located in the root zone and 14.3% near the porus acousticus internus. 24 cases were treated with decompression surgery, it indicated that the compression conditions just met the medical imaging examinationg results. After surgery the symptom disappeared in 23 cases and remarkably released in one case with no death case. We believed that this method might be helpful to idiopathic hemifacial spasm decompression surgery and other surgeries in the CP angle.     

Development of the Base Station Controller and Manager in the CDMA Mobile System

The base station (BS) in the CDMA Mobile System (CMS) connects calls through the radio interface and is designed to provide mobile subscribers with high quality service in spite of mobile subscribers’ motions. The BS consists of multiple base station transceiver subsystems (BTSs), a base station controller (BSC) and a base station manager (BSM). This paper is concerned with the BSC and the BSM. The BSC is located between the BTSs and the mobile switching center (MSC) connected with the public network, and is responsible for controlling mobile calls from and to mobile subscribers via the BTSs. The BSM provides operator-interfaces per the BS and takes responsibility of operation and maintenance (OAM) of the BS. Design of the BSC is based on two module types: functional module and unit module. The functional module is used to support new services easily and the unit module to increase the system capacity economically. Both modular types are easily achieved by inserting the corresponding modules to the system. Particularly, in order to efficiently support the soft handover which is one of CDMA superior advantages, the BSC adopts a large high-speed packet switch connecting up to 512 BTSs, and thus mobile subscribers can be provided with soft handover in high probability. The BSM is based on a commercial workstation to support OAM functions efficiently and guarantee high reliability of the functions. The BSM uses graphical user interface (GUI) for efficient OAM functions of the BS.     

Activity of NiO in (Ni,Mg)O Solid Solutions

Disagreement exists in the literature concerting the activity of NiO in (Ni,Mg)O solid solutions. Ideal behavior, as well as strong positive deviations and strong negative deviations from ideality, has been reported. In the present study, the activity of NiO was determined by electromotive force measurements using the solid-state cell Pt/Ni-NiO/0.92ZrO₂-0.08Y₂O₃/Ni-(Ni,Mg)O/Pt. The compositions studied had NiO mole fractions of 0.1,0.3,0.5,0.7, and 0.9. In agreement with theoretical expectations, the solid solutions exhibited ideal behavior at 882° and 982°C. Possible reasons for the conflicting results in the literature arc presented.     

Energy release rates of crack kinking by boundary condition sensitivity analysis

The energy release rate, which is the total derivative of the energy with respect to crack length, is recognized as corresponding to the shape sensitivity analysis with the crack length change represented by the tangential component of design velocity. In this paper the sensitivity formula recently developed for a changing boundary condition has been further extended to cover crack kinking under mixed mode loading. Due to difficulty in defining the velocity field at the corner, the energy release rate at the onset of crack kinking is obtained by extrapolating the energy release rates for finite length kinked cracks. A rectangular plate with a single edge slant crack under uniform tension is taken as a numerical example. The multi-region technique in the numerical implementation of the boundary integral equation is adopted to consider the asymmetry of the problem. Excellent accuracy is observed as compared with reference analytic solutions.     

硅中硼离子注入校准样品的研制

本文主要介绍了硅中硼离子注入校准样品的制备与研究。分别用三台SIMS仪器对样品进行了深度剖析与比对,并对用作校准目的的样品主要参数进行了定值。