Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

Electron Emission from Barium Strontium Titanate Ceramics

This paper focuses on understanding the influence of materials' properties on the ferroelectric electron emission. Ferroelectric ( x =1.0 and 0.8) and paraelectric ( x =0.67 and 0.5) compositions of barium strontium titanate (Ba _x Sr_{(1− x )}TiO₃) system were chosen for study based on their different ferroelectric and dielectric properties. Similar emission current waveforms were obtained from four compositions with negative triggering voltage applied to the rear electrode of the samples. It was difficult to explain the experimental results using the spontaneous polarization-switching model. The mechanism of electron emission from Ba _x Sr_{(1− x )}TiO₃ ceramics was ascertained to surface plasma emission.     

丝状真菌纤维素酶合成机制的研究

丝状真菌产生的纤维素酶被认为是最有应用前景的,但就目前酶生产效率来看,离实际应用还有很大的差距,需要对酶的合成调节机制有更为全面和深刻的了解。纤维素酶的生物合成受诱导和阻遏双重控制,酶的生产既有赖于低廉的保持一定浓度诱导物的存在,又必须清除分解代谢产物对酶合成的阻遏,其中的详细机制有待进一步的阐明。真菌纤维素酶的分泌也是相当复杂的,在酶的分泌过程中,酶会发生例如糖基化等一系列变化。提高纤维素酶的活力测定方法的准确性,使其进一步规范化,是研究纤维素酶工作的另外一个重要的领域。随着现代生物学朝着分子水平的不断发展,分子生物学的许多方法也越来越多地被应用于纤维素酶的研究中,并取得了重要进展。对真菌纤维素酶合成调节机制的深入研究,将为提高纤维素酶产量,推动应用工作的发展打下理论基础。     

扩链剂在PVC树脂生产中的应用

讨论了常见扩链剂的功能及在聚氯乙烯树脂生产中的应用。     

Synthesis,characterization, and thermal properties of phosphorus‐containing,wholly aromatic thermotropic copolyesters

A series of phosphorus‐containing, wholly aromatic thermotropic copolyesters from acetylated 2‐(6‐oxide‐6H‐dibenz〈c,e〉〈1,2〉oxa phosphorin‐6‐yl)‐1,4‐dihydroxy phenylene, p‐acetoxybenzoic acid, terephthalic acid, and isophthalic acid were prepared by melting polycondensation. The structure and basic properties of the polymers, such as the glass‐transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity, were investigated with Fourier transform infrared, elemental analysis, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray diffraction, and hot‐stage polarizing optical microscopy. The copolyesters had relatively high T_g values ranging from 183 to 192°C. The T_m values obtained from DSC curves for samples P‐20 and P‐25 were 290 and 287°C, respectively (where the number in the sample name indicates the molar fraction of the phosphorus‐containing monomer in the reactants). The initial flow temperatures of other samples observed with hot‐stage polarizing microscopy were 271–290°C. The 5% degradation temperatures in nitrogen ranged from 431 to 462°C, and the char yields at 640°C were 41–52%. All the copolyesters, except P‐40, were thermotropic and nematic. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1278–1284, 2002     

Improvement of Microwave Loss Tangent and Tunability of Ba0.55Sr0.45TiO3/MgO Composites Using the Heterogeneous Precipitation Method

Ba_0.55Sr_0.45TiO₃/MgO composites were successfully prepared by the heterogeneous precipitation method and their structural, surface morphological, tunable properties, and dielectric properties at microwave frequency were systemically investigated. Compared with the sample prepared by the traditional solid-state method, the sample prepared by the heterogeneous precipitation method exhibits a smaller grain size, more uniform microstructure, higher tunability, and lower microwave loss, and these properties are very beneficial to the development of the microwave tunable devices application. Moreover, the effects of La₂O₃ doping on the dielectric and tunable properties of BST/MgO composites are investigated. The result shows that the La³⁺-doped sample has higher tunability and lower microwave loss than the undoped one.     

Synthesis and self-assembly of hyperbranched polyester peripherally modified by touluene-4-sulfonyl groups

In this paper, hyperbranched polyesters (HPs) were synthesized in the molten state from 2,2-bis(hydroxymethyl) propionic acid (bis-MPA) and 2-ethyl-2-hydroxymethyl-1,3-propanediol (TMP) using acid catalysis. The modified hyperbranched polyesters were obtained through the chemical modification of the hyperbranched polyester cores by substituting a controlled fraction of the terminal hydroxyl groups with touluene-4-sulfonyl chloride using triethylamine (TEA) as an acceptor of HCl. The resultant polyesters were characterized by ¹H NMR, ¹³C NMR, FT-IR, UV and GPC and their self-assembly behaviors were investigated. The results revealed that self-assembled structures could be formed in selected solvents (trichloromethane/acetone or trichloromethane/n-hexane).     

金属间化合物的研究现状及其最新发展趋势

主要介绍了金属间化合物的概念、发展历程、研究现状及几种常用金属间化合物的发展状况，并提出了该类材料的最新发展趋势。     

复合泡沫塑料的性能改进研究

为改善复合泡沫塑料的介电性能,采用金属氧化物粒子填充改性双马来酰亚胺空芯玻璃微球复合泡沫塑料得到了高介电常数、低介质损耗因数、低密度、力学性能良好的电介质材料。     

High catalytic activity of PdOx/MnO2 for CO oxidation and importance of oxidation state of Mn

PdO_x/MnO₂ has been examined as a catalyst for CO oxidation using a conventional flow reactor at reaction temperatures between 50 and 150°C. In the reaction conditions of GHSV (gashourlyspacevelocity) of 1.22 × 10⁵/h and CO concentration of 2000 ppm, PdO_x/MnO₂ showed higher catalytic activity compared with PdO_x/Mn₂O₃, which had been previously reported as an effective catalyst due to the cooperative action of Pd and Mn₂O₃ for this reaction. The reason for higher activity of PdO_x/MnO₂ than PdO_x/Mn₂O₃ has been investigated using TPR (temperatureprogrammed reduction) and XPS studies. TPR showed that PdO_x/MnO₂ could be reduced by CO at much lower temperature than PdO_x/Mn₂O₃. During the experiment of reduction and oxidation, XPS showed that the valence of Mn in the PdO_x/MnO₂ was between 4+ and 3+, which is higher than that of Mn in the PdO_x/Mn₂O₃ catalyst of which the valence has been reported to be between 3+ and 2+. It is known that in this catalyst system the support supplies oxygen onto Pd, where the oxidation occurs with adsorbed CO, and the ability of the support to provide oxygen improves the performance of the catalyst. Therefore, it was concluded that the readiness of MnO₂ to be reduced with maintaining a higher oxidation state showed higher CO oxidation activity than Mn₂O₃ as support for PdO_x.