A gain-clamped SOA with distributed Bragg reflectors fabricated under both ends of active waveguide with different lengths

We demonstrate a gain-clamped semiconductor optical amplifier (GC-SOA) which has gratings under both end regions of an active waveguide. Two gratings of the new GC-SOA are fabricated in different lengths. Their lasing modes and gain characteristics are measured and analyzed with different combinations of grating lengths. It shows different gain and noise characteristics according to the measurement direction in asymmetric grating combinations.     

Thermal conductivity and mechanical properties of various cross-section types carbon fiber-reinforced composites

In this work, to study the characteristics of carbon fiber-reinforced composites with different fiber cross-section types, such as round, C, and hollow-shape, the thermal conductivity and mechanical properties were investigated and compared. The thermal conductivity was measured by means of steady-state method to the parallel and perpendicular direction of reinforcing fibers. The mechanical properties were evaluated by a variety of test methods i.e., flexural, interlaminar shear strength, and impact strength. As a result, it was found that the thermal conductivity was greatly depended on the cross-section type of the reinforcing fibers, as well as, the reinforcing orientation. Especially, the anisotropy factor (k _///k ) and the thermal diffusivity factor (_///) of C and hollow-type carbon fiber-reinforced composites showed about two times higher values than those of round-type one. Also, the mechanical results showed that C and hollow-type carbon fibers-reinforced composites had higher values than those of round-type one in all mechanical tested. These results were probably due to the basic properties of non-circular (C and hollow-type) carbon fiber which can improve interfacial binding forces and widen interfacial contact area between reinforcement and matrix, resulting in effectively transferring the applied stress.     

Piezoresistive effects of copper-filled polydimethylsiloxane composites near critical pressure

Piezoresistive properties of polydimethylsiloxane (PDMS) filled with copper particles in volume fraction above the electrical percolation threshold (25.3–50.7 vol%) were investigated. Piezoresistive behavior of the PDMS-copper composites under compressive pressure showed not only a change in resistance by approximately six orders of magnitude (∼1.5 MPa), but also a change in the critical pressure due to variations in the hardness of the composites. Resistivity relaxation was observed near the critical pressure and was explained through a stress relaxation and percolation mechanism. The mean tunneling distance was calculated by using a theoretical equation for percolation under compression. When the gauge factors of the composites were plotted versus strain, a universal curve was obtained regardless of the copper contents. Finally, the PDMS-copper composite demonstrated good repeatability, showing only small differences in the relative resistance after five successive tests.     

A closed-form expression for estimating radiated emissions from the power planes in a populated printed circuit board

An expression for the maximum intensity of radiated emissions from a rectangular power bus structure has been derived based on an analytical cavity-resonator model. The effect of components mounted on the board is modeled by modifying the propagation constant of the waves within the power bus structure. The radiated field intensity is calculated using the equivalent magnetic current around the edges of the power bus structure together with the modified propagation constant. Measurements of a populated test board show that the derived closed-form expression estimates the level of the maximum radiation intensity with reasonable accuracy.     

Cover Picture: Functionalization of Crystalline Colloidal Arrays through Click Chemistry (Adv. Mater. 21/2007)

Photonic crystals based on electrostatically‐stabilized colloidal arrays dispersed in a liquid medium are of interest to materials scientists partly because of the optical tuning afforded to theses systems with a variation in interparticle distance. On p. 3507, Stephen Foulger and co‐workers from Clemson University, USA report on a general strategy for the preparation of well‐defined and regioselectively functionalized ordered colloidal particles through the exploitation of “click” chemistry. Click transformations have found utility in the synthesis and/or functionalization of a range of systems. In addition, the solvochromic tuning of the ordered arrays is employed to modify the emission spectra of the surface‐attached photoluminescent dyes.     

Effects of moisture on properties of epoxy molding compounds

In this article the effects of moisture on a novel epoxy molding compound, including the mechanical properties, temperature transition, and thermal degradation behavior, are studied. The experimental results reveal that the absorbed water acts predominantly as a crazing agent, continuously decreasing the mechanical strength with the time in water. The glass-transition temperature decreases at the early stage and is finally equilibrated. The thermal degradation behavior of the materials is not greatly influenced by the hydrothermal age. The decomposition of samples in oxygen is composed of two independent steps: the thermal degradation and oxidation at high temperature. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2253–2259, 2001     

Microbial Assessment in School Foodservices and Recommendations for Food Safety Improvement

ABSTRACT:  This study evaluated microbial food safety in school foodservices. Five school foodservices were randomly selected, and samples from water, cooking utensils, tableware, foodservice surroundings, and linen were collected in summer and winter ( N = 420). Tap and drinking water samples were collected, samples of food contact surfaces were collected by swab-kit, and samples for foodservice workers' hands and gloves were prepared by glove juice method. Aerobic plate count (APC) and coliform bacterial populations were enumerated on plate count agar (PCA) and desoxycholate lactose agar, respectively. The presence of Escherichia coli , Salmonella , Listeria monocytogenes , and Staphylococcus aureus was also examined by biochemical identification tests. In addition, PCA agar for APCs and Baird-Parker agar for S . aureus were used to enumerate airborne microorganisms. Higher APCs (< 0 to 5.1 log CFU/mL) than acceptable level were generally observed in water samples, while low coliform counts were found in the samples. High APCs were enumerated in cooking utensils, foodservice workers, tableware, and foodservice surroundings, and coliforms were also found in the samples for both seasons. The presence of Salmonella was found from only 10% of plastic glove samples (summer), and the presence of L . monocytogenes was not observed in all samples. S . aureus was detected in some of water, cooking utensils, tableware, employees, and foodservice surroundings, and E . coli was observed in cooking utensils (10% to 20%; summer). No obvious airborne bacteria were detected. These results showed that sanitation practice in school foodservices should be improved, and the results may be useful in microbial assessment of school foodservices.     

Nanostructural and optical features of nc-Si:H films prepared by nickel-induced crystallization

A 30-nm-thick Ni layer was deposited on top of the nc-Si:H (hydrogenated nanocrystalline Si) films by rf-magnetron sputter, and then heat-treatments were carried out at temperatures of 350–500^∘C. Si nanocrystallites were formed in the Ni/nc-Si:H bilayer films during the post-deposition heat-treatments. The intensity of the photoluminescence spectra of the post-deposition heat-treated films gradually increased at wavelengths of ∼420 as well as ∼580 nm with raising the annealing temperature from 350 to 500^∘C. It is highly likely that the increase of the photoluminescence intensity is caused by the increase in the total volume of the nanocrystallites in the films. It was found that the nickel-induced crystallization processing enhanced the formation of Si cystallites with the size of ∼2 and ∼5 nm in the films.     

Biofilter in water and wastewater treatment

Biofilter is one of the most important separation processes that can be employed to remove organic pollutants from air, water, and wastewater. Even though, it has been used over a century, it is still difficult to explain theoretically all the biological processes occurring in a biofilter. In this paper, the fundamental of biological processes involved in the biofilter is critically reviewed together with the mathematical modeling approach. The important operating and design parameters are discussed in detail with the typical values used for different applications. The most important parameter which governs this process is the biomass attached to the medium. The relative merits of different methods adopted in the measurement of the biomass are discussed. The laboratory-and full-scale applications of the biofilter in water and wastewater treatment are also presented. Their performances in terms of specific pollutant removal are highlighted.