Microscopic simulation of electronic noise in semiconductormaterials and devices

We present a microscopic interpretation of electronic noise in semiconductor materials and two-terminal devices. The theory is based on Monte Carlo simulations of the carrier motion self-consistently coupled with a Poisson solver. Current and voltage noise operations are applied and their respective representations discussed. As application we consider the cases of homogeneous materials, resistors, n⁺nn ⁺ structures, and Schottky-barrier diodes. Phenomena associated with coupling between fluctuations in carrier velocity and self-consistent electric field are quantitatively investigated for the first time. At increasing applied fields hot-carrier effects are found to be of relevant importance in all the cases considered here. As a general result, noise spectroscopy is found to be a source of valuable information to investigate and characterize transport properties of semiconductor materials and devices     

Current-mode A/D converter

The authors report the design of a new current-mode A/D converter, based on a modified successive-approximations model, in 1.2 μm CMOS technology. The proposed circuit is characterised by good accuracy and fast dynamic performance, low power consumption and small occupation area. SPICE simulations allow the design approach to be validated and the electrical performance of the ADC to be predicted     

Filter matrix estimation in automated DNA sequencing

In four-color fluorescence-based automated DNA sequencing, a 4×4 filter matrix parameterizes the relationship between the dye-intensity signals of interest and the data collected by an optical imaging system. The filter matrix is important because the estimated DNA sequence is based on the dye intensities that can only be recovered via inversion of the matrix. Here, the authors present a calibration method for the estimation of the columns of this matrix, using data generated through a special experiment in which DNA samples are labeled with only one fluorescent dye at a time. Simulations and applications of the method to real data are provided, with promising results     

Analysis of the deformation of polypropylene hot-tool butt welds

Thin microtomed samples from hot-tool butt welds of polypropylene pipes are subjected to uniaxial tensile stress using a specially built instrumented microtesting machine. The deformation of the interface between the weld and the bulk polymer is measured by an optical method. An analysis of these measurements is carried out using the finite element method, and contours of the effective stress are obtained. There is a steep stress gradient at the junction of the weld flash and the bulk polymer, although the stress concentration factor is relatively low. The stress is essentially constant in the bulk polymer apart from the region near the weld zone. Tests on samples without the weld flash show that the maximum stress occurs within the weld zone. This is consistent with long-term tests on larger samples, where the fracture is found to initiate within the weld. The method of analysis enables the stress-strain response of the weld material to be determined.     

The pharmacokinetics of pancuronium bromide in infants, children and adults

Laparoscopic retroperitoneal lymph node dissection is a new surgical procedure used to enhance staging in men with clinical stage I nonseminomatous germ cell tumors of the testis. The procedure has been performed in a limited number of patients at several centers with extensive laparoscopic experience. Laparoscopic retroperitoneal lymphadenectomy is a technically demanding procedure which can be successfully completed in the majority of patients. However, the risk of complications is greater than in patients who undergo standard open retroperitoneal lymph node dissection. The primary advantage of a laparoscopic approach is shortened hospitalization and rapid return to normal activity. The role of laparoscopy in the management of patients with testis malignancy has not been defined. The use of this staging procedure may help minimize the need for surveillance studies following surgery and may be best utilized in men with a lower likelihood of nodal metastases. Ultimately, prospective study in large groups of patients will be necessary to determine the role of laparoscopic retroperitoneal lymph node dissection in patients with testis cancer.     

Efficient diode-pumped single-frequency erbium:ytterbium fiberlaser

We report a 7.6-mW single-frequency fiber laser operating at 1545 nm, using for the first time an Er³⁺:Yb³⁺ doped fiber and a fiber grating output coupler. The laser did not exhibit self-pulsation, which is a typical problem in short three-level fiber lasers, and had a relative intensity noise (RIN) level below -145.5 dB/Hz at frequencies above 10 MHz. The linewidth of the laser was limited by the relaxation oscillation sidebands in the optical spectrum and was typically less than 1 MHz     

The effects of cholecystokinin A and B receptor antagonists, devazepide and L 365260, on citalopram-induced decrease of exploratory behaviour in rat

The present study has been divided into two sets. In the first set, the aim of the experiments was to investigate the dose-response effect of selective serotonin re-uptake inhibitor (SSRI) citalopram on rat exploratory behaviour in the elevated plus-maze. In the second set of experiments, the effect of cholecystokinin (CCK) CCKA and CCKB receptor antagonists, devazepide and L 365260, on citalopram-induced decrease of exploratory behaviour in the elevated plus-maze was studied. Citalopram (5 and 10 mg/kg) decreased the number of open and total arm entries, line crossings on open arms, and percentage of time spent exploring in open arm. Dose 15 mg/kg was without any effect on rat exploratory behaviour. Devazepide (0.01 and 1.0 mg/kg) failed to modify any of the citalopram-induced changes observed. L 365260 (1.0 mg/kg) reversed most of the effects of citalopram: the numbers of open and total arm entries, the number of line crossings, and the percentage of time spent exploring in open arms. L 365260 at dose level 0.01 mg/kg was ineffective. These results support the involvement of the CCKB receptor subtype in SSRI-induced anxiogenic-like effects in rodents.     

Sorption of vapors and gases by cellulose acetate films

Cellulose diacetate and triacetate films 6–55 µm thick with a total porosity of 0.8–2% were prepared by pouring a solution on an immobile surface and by calendering. Sorption of H₂S and CO₂ gases and acetone vapors on these films was investigated in static and dynamic conditions. It was shown that films 6–10 µm thick prepared by calendering should be used for purification of air from H₂S and CO₂ and films 15–20 µm thick prepared by pouring should be used for removal of acetone vapors.Engels Institute of Technology, Saratov State University. Translated from Khimicheskie Volokna, No. 6, pp. 44–46, November–December, 1995.     

Modeling ion implantation of HgCdTe

Ion implantation of boron is used to create n on p photodiodes in vacancy-doped mercury cadmium telluride (MC.T). The junction is formed by Hg interstitials from the implant damage region diffusing into the MC.T and annihilating Hg vacancies. The resultant doping profile is n⁺/n^-/p, where the n⁺ region is near the surface and roughly coincides with the implant damage, the n^- region is where Hg vacancies have been annihilated revealing a residual grown-in donor, and the p region remains doped by Hg vacancy double acceptors. We have recently developed a new process modeling tool for simulating junction formation in MC.T by ion implantation. The interstitial source in the damage region is represented by stored interstitials whose distribution depends on the implant dose. These interstitials are released into the bulk at a constant, user defined rate. Once released, they diffuse away from the damage region and annihilate any Hg vacancies they encounter. In this paper, we present results of simulations using this tool and show how it can be used to quantitatively analyze the effects of variations in processing conditions, including implant dose, annealing temperature, and doping background.