Stability of a-Si:H solar cells deposited by Ar-treatment or by ECR techniques

Stability against light soaking was studied for amorphous silicon (a-Si:H) solar cells using three different i-layers; (a) device-quality a-Si:H (standard a-Si:H) with bandgap of 1.75 eV, (b) narrow bandgap (1.55 eV) a-Si:H fabricated by Ar* chemical annealing and (c) a-Si:H(Cl) fabricated from SiH₂Cl₂. Both the narrow bandgap a-Si:H and the a-Si:H(Cl) solar cells showed much improved stability than that of the standard a-Si:H solar cells: e.g., fill factor of the narrow bandgap a-Si:H cell only slightly decreased from 56% to 53%, while that of the standard a-Si:H cell degraded from 62% to 51%. In addition, mobility–lifetime products of the a-Si:H(Cl) cell also exhibited improved stability than that of the standard a-Si:H solar cell.     

Mineral admixtures in mortars: Quantification of the physical effects of inert materials on short-term hydration

This work is the second part of an overall project, the aim of which is the development of general mix design rules for concrete containing different kinds of mineral admixtures. The first part presented the separation of the different physical effects responsible for changes in cement hydration when chemically inert quartz powders are used in mortars. This second part describes the development of an empirical model, based on semiadiabatic calorimetry measurements, which leads to the quantification of the enhancement of cement hydration due to the heterogeneous nucleation effect at short hydration times. Experimental results show that not all the admixture particles participate in the heterogeneous nucleation process. Consequently, the concept of efficient surface S_eff is introduced in the model. S_eff is the total admixture surface S (m² of mineral admixture/kg of cement) weighted by a function ξ(p). The efficiency function ξ(p) depends only on the replacement rate p and is independent of time, fineness and type of mineral admixture used. It decreases from 1 to 0: Low replacement rates give an efficiency value near 1, which means that all admixture particles enhance the hydration process. An efficiency value near 0 is obtained for high replacement rates, which indicates that, from the hydration point of view, an excess of inert powder does not lead to an increase in the amount of hydrates compared with the reference mortar without mineral admixture. The empirical model, which is mainly related to the specific surface area of the admixtures, quantifies the variation of the degree of hydration induced by the use of inert mineral admixtures. One application of the model, coupled with Powers' law, is the prediction of the short-term compressive strength of mortars.     

Mineral admixtures in mortars effect of type, amount and fineness of fine constituents on compressive strength

This work is the third part of an overall project the aim of which is the development of general mix design rules for concrete containing different kinds of mineral admixtures (also named mineral additions or mineral constituents). It deals with the compressive strength of mortars made with up to 75% of crushed quartz, limestone filler or fly ash of different fineness. The paper presents all the experimental results as a sort of database and emphasizes the effects on strength of the nature, amount and fineness of mineral admixtures. For short hydration times (1 to 2 days), the nature of mineral admixture is not a significant parameter, as mortars containing the same amount of different kinds of admixtures having equivalent fineness present similar strengths. For long hydration times (up to 6 months), the excess strength due to fly ash pozzolanic activity is quantified by the difference between the strengths of mortars containing the same proportions of inert and pozzolanic admixtures with the same fineness. In the case of inert mineral admixtures, the increase in strength with the fineness of mineral admixtures cannot be explained by the filler effect, but can be attributed to the physical effect of heterogeneous nucleation. In the next part of this work, these results will be used for the elaboration of an empirical model leading to the quantification of both physical and chemical effects. This model presents strong similarities with the previous model based on calorimetric results.     

Noninvasive Measurement of the Volume Elastic Modulus in Finger Arteries Using Photoelectric Plethysmography

A method for the nonivasive measurement of the volume elastic modulus (Ev) in human finger arteries was developed. The volume change ratio and pulse pressure in the arteries were simultaneously determined by a transmittance type infrared photoelectric plethysmograph and a volume oscillometric sphygmomanometer using an occlusive cuff. The Ev values could be obtained at a desired transmural pressure level of the arteries which was controlled by the cuff. A clear difference was revealed between the Ev values obtained in the fingers of two male subjects of 33 and 65 years old. The values determined by this method were compared to those calculated from pulse wave propagation velocity (Evp) obtained simultaneously in the fingers of 11 subjects. The linear regression equation was Ev = 1.31 Evp ?0.117 with a correlation coefficient r = 0.893 (n = 39). These results suggest that this should be a useful and noninvasive method of evaluating changes in arterial elasticity accompanying aging and perhaps influenced by accompanying hypertension or arteriosclerosis.     

Thermal proof testing of ceramics

The possibility of thermal proof testing with thermal stress induced by quenching was examined. For this purpose, the bending strength and the critical temperature difference for quenching into water and quench oil for soda-lime-silica glass were measured before and after proof testing by quenching the specimens into water, ethyl alcohol, silicon oil and quench oil. Proof testing by water, ethyl alcohol and silicon oil quenching modified the distribution of the critical temperature difference as expected, but not that of the bending strength at all. It is suggested that proof testing by rapid quenching is a useful method for truncating the critical temperature difference distribution of ceramic components of heat engines and so on.     

Inlet plenum pressure drop calculation for a cross-flow module

Outlined here is a method for applying a model of discharge flow through a series of sharp-edged orifices from an inlet plenum, to accurately predict the total pressure drop across the flow distribution geometry. This particular case relates to a cross-flow filtration membrane module, but is applicable for any flow distribution system of a similar format.     

Group feature extraction based on matrix factorization from long-range office-logging data

To increase the productivity of knowledge workers, it is necessary to manage their organization so that they are motivated to collaborate with each other for their synergy. However, it is difficult for managers to grasp the explicit interactions of workers in the organization all the time. Owing to advanced communications technology, and the reduced size and improved capabilities of computers, we are able to record group behaviors as logging data in the office. The aim of this study is to extract features of group behavior from long-range office-logging data. We apply principal component analysis to the data matrix whose element is the mean travel velocity calculated from an individual’s trajectory per day. The results demonstrate the feasibility of our approach, since nontrivial informative group features can be extracted.     

Control of nano-sized interlayer space of lamellar vanadyl benzylphosphate

Nano-sized interlayer space of lamellar vanadyl benzylphosphate was controlled by water content in starting solution. Depending on the water content, three types of lamellar vanadyl benzylphosphate having basal spacings of 1.4 nm, 1.9 nm and 2.3 nm were obtained. It was suggested that the difference in the concentrations of benzyl and hydroxyl groups in the interlayer leads to the variation of the interlayer space.