PVC membrane potentiometric sensor based on 5-pyridino-2,8-dithia[9](2,9)-1,10-phenanthroline-phane for selective determination of neodymium(III)

Spectrofluorometric studies on the binding properties of 5-pyridino-2,8-dithia[9](2,9)-1,10-phenanthrolinephane (L) toward La3+, Sm3+, Gd3+, Yb3+, and Nd3+ in methanol solution revealed the occurrence of both 1:1 and 2:1 (ligand/metal) complexation with a stability order of Nd3+ > Yb3+ > Gd3+ > Sm3+ > La3+. Consequently, L was used as a suitable neutral ionophore for the preparation of a novel polymeric membrane-selective electrode for Nd3+ ion. The electrode exhibited a Nernstian response over a wide concentration range (1.0 x 10(-6)-1.0 x 10(-2) M) with a low limit of detection of 7.9 x 10(-7) M. The electrode possesses a fast response time of <5 s and can be used for at least 9 weeks without observing any considerable deviation. The proposed electrode revealed a very good selectivity for Nd3+ over a wide variety of alkali, alkaline earth, transition, and heavy metal ions, including members of the lanthanide family other than Nd3+. The potentiometric response of the electrode is independent of the pH of test solution in the pH range 4.0-6.5. The proposed electrode was successfully applied to the recovery of Nd3+ ion from tap water samples and, also, as an indicator electrode, in potentiometric titration of neodymium(III) ions.     

A 5.2 mW 240–550 MHz continuous-time low-pass filter and VGA for a UWB receiver in 0.18 μm CMOS process

A very low-power wide-band CMOS continuous-time low-pass filter for a ultra wideband system receiver in 0.18-μm CMOS technology is proposed. The cutoff frequency of the fourth-order LPF can be tuned within 240–550 MHz. The gain of the filter is tuned about 44 dB which can omit the variable gain amplifier (VGA) block. An IIP3 of 17.4 dBm is achieved for a power consumption of 5.2 mW from a 1.8 V power supply. Merging LPF and VGA into one block can efficiently reduce the power consumption and the chip area of the analog baseband channel while achieving a high linearity.     

Multi- Objective Optimal Design of on- Demand Pressurized Irrigation Networks

In the context of water as an economic good, from the use of water, one can derive a value, which can be affected by the reliability of supply. On-demand irrigation systems provide valuable water to skilled farmers who have the capacity to maximize economic value of water. In this study, simultaneous optimization of on-demand irrigation network layout and pipe sizes is considered taking into account both investment and annual energy costs. The optimization problem is formulated as a problem of searching for the upstream head value, which minimizes the total cost (investment and energy costs) of the system. The investment and annual energy costs are obtained in two separate phases. Max–Min ant system (MMAS) algorithm is used to obtain the minimum cost design considering layout and pipe diameters of the network simultaneously. Clement methodology is used to determine flow rates of pipelines at the peak period of irrigation requirements. The applicability of the proposed method is showed by re-designing a real world example from literature.     

Elastomeric Fibrous Hybrid Scaffold Supports In Vitro and In Vivo Tissue Formation

Biomimetic materials with biomechanical properties resembling those of native tissues while providing an environment for cell growth and tissue formation, are vital for tissue engineering (TE). Mechanical anisotropy is an important property of native cardiovascular tissues and directly influences tissue function. This study reports fabrication of anisotropic cell‐seeded constructs while retaining control over the construct's architecture and distribution of cells. Newly synthesized poly‐4‐hydroxybutyrate (P4HB) is fabricated with a dry spinning technique to create anelastomeric fibrous scaffold that allows control of fiber diameter, porosity, and rate ofdegradation. To allow cell and tissue ingrowth, hybrid scaffolds with mesenchymalstem cells (MSCs) encapsulated in a photocrosslinkable hydrogel were developed. Culturing the cellularized scaffolds in a cyclic stretch/flexure bioreactor resulted in tissue formation and confirmed the scaffold's performance under mechanical stimulation. In vivo experiments showed that the hybrid scaffold is capable of withstanding physiological pressures when implanted as a patch in the pulmonary artery. Aligned tissue formation occurred on the scaffold luminal surface without macroscopic thrombus formation. This combination of a novel, anisotropic fibrous scaffold and a tunable native‐like hydrogel for cellular encapsulation promoted formation of 3D tissue and provides a biologically functional composite scaffold for soft‐tissue engineering applications.     

Power Balance Consideration in the Design of Indirectly Driven Targets

A preliminary design for a heavy ion driver inertial fusion(HIDIF) target is presented. The effect of target material and dimensions on transfer efficiency and symmetrical irradiation in the hohlraum are investigated.The analysis led to the evaluation of optimal target materials and dimensions to achieve a positive power balance of an ICF power plant.The results show that the best choice is a high Z material for cavity wall materials and a low Z material for the capsule ablator.It is concluded that for achieving the highest transfer efficiency and best symmetrization we need an area ratio between 5≤A2/A1≤9.     

Role of Crystallographic Textures on Failure Behavior in HSLA Grade-420 Steel During Cold Rolling

The microstructural and textural evolution was analyzed during rolling at room temperature to obtain detailed information about the failure behavior in HSLA grade-420 steel. Electron backscatter diffraction measurements were carried out in both non-cracked and cracked areas after cold rolling to find a correlation between microstructural parameters (i.e., grain orientation, grain boundary characteristics and Taylor factor) and crack propagation. The results showed that the crack tended to propagate along grains oriented with {001} planes parallel to the normal direction with high Taylor factor value. The special boundaries associated with the {111}, {110} and {221} planes were indicated as crack resistance, while ∑ 5, 13a and 17a, which related to the {001} planes, were crack-susceptible. Transgranular cracking was subjected within grains with high Taylor factor, while mismatch in Taylor factor between neighboring grains could provide an easy path for intergranular crack propagation.     

On the Occurrence of Liquation During Linear Friction Welding of Ni-Based Superalloys

A combination of experimental and analytical methods was used to study the possible occurrence of liquation during LFW of the newly developed AD730^TM Ni-based superalloy. LFWed joints were produced using a semi-industrial size facility and the interfaces of the joints as well as the ejected flash were examined using optical and Field Emission Gun Scanning Electron Microscopy (FEG-SEM). Physical simulation of the LFW thermal cycle, using thermomechanical simulator Gleeble™ 3800, showed that incipient melting started from 1473 K (1200 °C). The analytical model, calibrated by experiments, predicted that the highest temperature of the interface was about 1523 K (1250 °C). The constitutive equations based on lattice and pipe diffusion models were developed to quantify the self-diffusivity of the elements and control the extent of liquation by considering the effect of LFW process parameters. Analytical results show that the application of compressive stresses during LFW results in 25 times increase in the diffusion of Ni atoms at the weld interface. Therefore, no presence of re-solidified phases, i.e., occurrence of liquation, was observed in the microstructure of the weld zone or the flash in the present study. Based on the obtained results, a methodology was developed for designing the optimum pressure above which no liquation, and hence cracking, will be observable.

     

Pricing the financial Heston–Hull–White model with arbitrary correlation factors via an adaptive FDM

This paper is concerned with the pricing procedure of one of the most challenging models known as the Heston–Hull–White partial differential equation (PDE) in option pricing, at which the model is a time-dependent 3D linear PDE including three mixed derivative terms. The model comes from the fact that the price, the volatility and the interest rate are assumed to be stochastic processes. To contribute and avoid huge discretized systems, an adaptive distribution of the nodes (viz, nonuniform nodes) is taken into account with emphasis on the hot area of the solution curve. New adaptive finite difference (FD) formulas of higher orders are constructed on these meshes. Then, a set of semi-discretized equations is attained which is tackled by a time-stepping method. Several financial tests are discussed in detail to reveal the superiority of the proposed approach.     

Area-Efficient 60 GHz +18.9 dBm Power Amplifier with On-Chip Four-Way Parallel Power Combiner in 65-nm CMOS

This paper presents a compact 60-GHz power amplifier utilizing a four-way on-chip parallel power combiner and splitter. The proposed topology provides the capability of combining the output power of four individual power amplifier cores in a compact die area. Each power amplifier core consists of a three-stage common-source amplifier with transformer-coupled impedance matching networks. Fabricated in 65-nm CMOS process, the measured gain of the 0.19-mm² power amplifier at 60 GHz is 18.8 and 15 dB utilizing 1.4 and 1.0 V supply. Three-decibel band width of 4 GHz and P_1dB of 16.9 dBm is measured while consuming 424 mW from a 1.4-V supply. A maximum saturated output power of 18.3 dBm is measured with the 15.9% peak power added efficiency at 60 GHz. The measured insertion loss is 1.9 dB at 60 GHz. The proposed power amplifier achieves the highest power density (power/area) compared to the reported 60-GHz CMOS power amplifiers in 65 nm or older CMOS technologies.