钻井井架力学性能分析

钻井井架作为钻机系统设备中的关键部分,其力学性能直接关系到整套钻机系统的安全生产。文章推导了常用于分析钻井井架力学性能的理论,即线性屈曲、几何非线性和双重非线性理论。提出同时用这三种理论对钻井井架进行综合比较分析,从而合理地预见井架力学性能的方法。以A形钻井井架为例,进行了详细的分析,得到了井架的失稳形式、极限承载、破坏特征及薄弱部位,为钻井井架的设计、优化与评定提供了参考。     

防霉建筑涂料的研究与施工使用

针对国内外防霉建筑涂料存在的问题，研制开发了以合成树脂为主要成膜物质，加入环保性杀菌防霉剂及具有防腐霉的功能性颜填料，再配以树脂固化剂等成分配制而成的高性能防霉建筑涂料，并指出该涂料防霉效果良好。     

110kV变电站35kV高压系统边运行边改造实践

对宣钢供电系统110kV变电站35kV高压系统边运行边施工改造经验进行了分析探讨。指出选用优良的设备、制定周密的安全措施，能够确保施工、运行安全。     

Accumulation and Mixing of Oils in Jinghu Sag of Subei Basin： Constraints from Thermal Maturity Parameters

Oils in Jinghu sag are abundant with high content of polar compounds and have a low ratio of saturate to aromatic hydrocarbons and a high ratio of resin to asphaltene. The gross composition of oils in the Jinghu sag suggests typical immature to low mature characteristics. Some compounds with low thermal stability were identified. Light hydrocarbons, a carbon preference index, an odd even index, n-alkane and hopane maturity parameters show mature features and little differences in the maturity level among oils. Sterane isomerization parameters indicate an immature to low mature status of oil. Transfer of the sedimentary center during sedimentation has led to different thermal histories among subsags and thus generated oils with different maturities. On the basis of source analyses, four migration and accumulation patterns with different maturity can be classified. Combined with available information on mergers of source, reservoir and long distance oil lateral migration, mixing conditions were present in the Jinghu sag. Experimental results indicate that maturity variations are caused by mixtures of hydrocarbons with different maturity.     

Numerical Simulation of Independent Advance of Ore Breaking in the Non-pillar Sublevel Caving Method

The mechanism of stress generation and propagation by detonation loading in five separate independent advance of ore breaking patterns is discussed in the paper. An elastic numerical model was developed using AN- SYS/LS-DYNA 3D Nonlinear Dynamic Finite Element Software. In this package ANSYS is the preprocessor and LS-DYNA is the postprocessor. Numerical models in the paper to actual were l：10 and the element mesh was dissected in scanning mode utilizing the symmetry characteristics of the numerical model. Five different advance rates were studied. Parameters, such as the time required to maximum stress, the action time of the available stress, the maximum velocity of the nodes, the stress penetration time, the magnitude of the stress peak and the time duration for high stress were numerically simulated. The 2.2 m advance appeared optimum from an analysis of the simulation results. The results from numerical simulation have been validated by tests with physical models.     

新型梳形电缆防火墙的应用

通过新型梳形电缆防火墙的实施，有效地限制了电缆火灾范围，增强了电缆防火、隔火能力，并详细地介绍了梳形电缆防火墙的原理结构、安装使用和注意事项。     

用熵方程证明全不可逆循环揭示的Clausius方程式

利用不可逆循环图代替传统的半不可逆循环推导出Clausius积分式，并用熵方程证明之，得出可逆过程膨胀功大于不可逆过程膨胀功。     

关于约束方差控制器的评估问题的研究

本文研究当系统的性能指标表现为系统输入及输出的方差约束时一类随机控制器的评价问题，给出了系统反馈输入及输出的辨识算法，该算法可用来评价反馈控制器能否使反馈系统满足既定的方差约束，以便在对实际系统实施控制之前及时调整控制器，从而达到设计目的。