External quantum efficiency response of thin silicon solar cell based on plasmonic scattering of indium and silver nanoparticles

This study characterized the plasmonic scattering effects of indium nanoparticles (In NPs) on the front surface and silver nanoparticles (Ag NPs) on the rear surface of a thin silicon solar cell according to external quantum efficiency (EQE) and photovoltaic current–voltage. The EQE response indicates that, at wavelengths of 300 to 800 nm, the ratio of the number of photo-carriers collected to the number of incident photons shining on a thin Si solar cell was enhanced by the In NPs, and at wavelengths of 1,000 to 1,200 nm, by the Ag NPs. These results demonstrate the effectiveness of combining the broadband plasmonic scattering of two metals in enhancing the overall photovoltaic performance of a thin silicon solar cell. Short-circuit current was increased by 31.88% (from 2.98 to 3.93 mA) and conversion efficiency was increased by 32.72% (from 9.81% to 13.02%), compared to bare thin Si solar cells.     

Solid‐state NMR study of spin finish of thermally treated PAN and PAN/CNT precursor fibers

Dry‐jet wet‐spun polyacrylonitrile (PAN) and PAN/carbon nanotubes (CNTs) precursor fibers coated by spin finishes were characterized using the solid‐state ¹H nuclear magnetic resonance technique. Series of fiber samples were prepared upon thermal treatment at different temperatures (room temperature to 180°C). Using the Hahn echo sequence, relatively mobile components were identified and the effect of the heat treatment on those components was studied. It was observed that the mobile components are mainly the spin finishes. Heat treatment caused loss of one of the spin finishes (Type B) to a great extent (～80%), whereas the other two spin finishes (Type A and Type C) were more stable. Additional information regarding the change in molecular mobility due to heat treatment was obtained by the spin‐lattice relaxation time ( T₁ ) analysis. It was found that the presence of CNT affects the T₁ relaxation time of the polymer in the composite fiber, however, that of relatively mobile components remains unaffected. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40734.     

Room temperature multiferroic properties of Ni-doped Aurivillus phase Bi5Ti3FeO15

Single-phase Aurivillius Bi₅Ti₃Fe_0.5Ni_0.5O₁₅ (BTFN) ceramics were synthesized by the solid-state reaction method. The substitution of Ni for half Fe ions does not introduce magnetic impurity phase but increases magnetic moment more than two orders. The ferroelectric and magnetic Curie temperatures are determined to be 1100 K and 726 K. The room-temperature multiferroic behavior of the BTFN ceramics were demonstrated by the ferroelectric (2P_r=8.5 μC/cm², 2E_c=74 kV/cm) and ferromagnetic (2M_r=27.86 m emu/g, 2H_c=553 Oe) measurements. The ferromagnetism can be ascribed to the aggregation of magnetic ions at the inner octahedra by Ni doping and the spin canting of magnetic-ion-based sublattices via the Dzyaloshinskii-Moriya interaction. The present work suggests the possibility of doped Bi₅Ti₃FeO₁₅ as a potential room-temperature multiferroic.     

Synthesis and characterization of segmented poly(ether ester amide)s from diglycol,adipic acid,and a nylon‐6 oligomer

This article presents a convenient method for synthesizing segmented poly(ether ester amide)s (PEEAs) by polycondensation and chain extension. A nylon‐6 oligomer prepared from ε‐caprolactam and ethanolamine through ring‐opening polymerization was polymerized with adipic acid and diglycol to prepare PEEA prepolymers (PrePEEAs) with ether linkages and amide contents ranging from 20 to 60 mol%. Chain extension of the PrePEEAs was conducted at 200°C using 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) and carbonyl biscaprolactamate as combination chain extenders. The chain‐extended PEEAs (ExtPEEAs) were characterized by viscometry, gel permeation chromatography, FT‐IR, ¹H‐NMR, differential scanning calorimetry, thermogravimetric analysis, wide angle X‐ray diffraction, and tensile testing. Results show that incorporation of nylon‐6 segments yields semicrystalline ExtPEEAs and that introduction of ether linkages improves the flexibility of the resultant polymers. ExtPEEAs showed T_m from 107.6 to 137.3°C, good thermal stability with initial decomposition temperatures above 337.3°C, and tensile strengths of up to 27.4 MPa with strains at break ranging from 231.24 to 1052.52%. POLYM. ENG. SCI., 55:763–770, 2015. © 2014 Society of Plastics Engineers     

Particle Size Control and Crystal Habit Modification of Phenacetin Using Ultrasonic Crystallization

Power ultrasound is applied for cooling crystallization to control and modify the particle size and crystal habit of an active pharmaceutical ingredient, phenacetin. Operating parameters including sonication intensity and duration, solution concentration, and cooling rate are studied and compared. With respect to mean particle size, the effect of sonication intensity is most significant. In addition, the crystal habit of recrystallized phenacetin is modified substantially and shows an elliptic shape. Recrystallized phenacetin also provides an enhanced dissolution rate compared with the original sample. These results prove that ultrasonic crystallization is an efficient tool for controlling the solid‐state properties of an active pharmaceutical ingredient.     

Study on the preparation and mechanical properties of injection‐moulded wood‐based plastics

The objectives of this study were to prepare injection‐moulded wood‐based plastics and to characterize their mechanical properties. Injection‐moulded wood‐based plastics with satisfactory flexural (65.7 MPa) and tensile strengths (30.1 MPa) were successfully obtained through a simple reaction of mulberry branch meal with phthalic anhydride (PA) in 1‐methylimidazole under mild condition. The X‐ ray diffraction results indicated complete disruption of the crystallinity of cellulose because the pattern obtained for esterified fiber was almost a straight line without any peaks. The peaks in the Fourier transform infrared spectroscopy spectra (1738 and 748 cm^?1) and NMR spectra (173.3 and 133.5 ppm) indicated the attachment of 0‐carboxybenzoyl groups onto the wood fibers via ester bonds. The differential scanning calorimetry curves showed that the glass transition temperature decreased with increasing weight percentage gain (WPG). The derivative thermogravimetric analysis curves indicated that esterified wood fiber was less thermally stable than the untreated fiber and that the component tends to be homogeneous with increasing WPG. Scanning electron microscope revealed that the fractured surfaces of most samples were smooth and uniform but that high temperature and less PA dosage could lead to the appearance of holes and cracks. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41376.     

Morphology and mechanical properties of dual‐curable epoxyacrylate hybrid composites

A dual‐curable epoxyacrylate (EA) oligomer with one epoxide group and one vinyl group at each end was synthesized for the application as adhesive sealant in the liquid crystal display panels. However, after UV and thermal cure, the EA resin was brittle with a poor resistance to crack initiation and propagation. Liquid rubbers with different functional end groups were thus tried as toughening agents for the EA resin. Among all the rubber‐toughened EAs, the EA‐V5A5 added with vinyl‐terminated and amino‐terminated butadiene‐acrylonitrile copolymers (VTBN and ATBN) each at 5 phr had the highest fracture toughness, tensile strength, and elongation at break but a lower initial modulus. To raise the modulus, submicron‐sized silica particles (∼170 nm) with surface vinyl functional groups were further added to the EA‐V5A5 to prepare the hybrid composites. Because of interfacial chemical bonding provided by the surface vinyl functional groups, both modulus and fracture toughness were increased by adding silica particles, without any appreciable decrease in extensibility. For the hybrid composite at 20 phr silica particles, the initial modulus, fracture toughness, and fracture energy were raised by 10.3, 100, and 267%, respectively, when compared to the neat epoxyacrylate. Owing to their strong interfacial bonding, the increase of fracture toughness was mainly due to the crack deflection and bifurcation on silica particles, in addition to the rubber particle bridging and tearing as evidenced by SEM pictures on the fracture surface. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41820.     

Advances in the Study of the Antiatherogenic Function and Novel Therapies for HDL

The hypothesis that raising high-density lipoprotein cholesterol (HDL-C) levels could improve the risk for cardiovascular disease (CVD) is facing challenges. There is multitudinous clear clinical evidence that the latest failures of HDL-C-raising drugs show no clear association with risks for CVD. At the genetic level, recent research indicates that steady-state HDL-C concentrations may provide limited information regarding the potential antiatherogenic functions of HDL. It is evident that the newer strategies may replace therapeutic approaches to simply raise plasma HDL-C levels. There is an urgent need to identify an efficient biomarker that accurately predicts the increased risk of atherosclerosis (AS) in patients and that may be used for exploring newer therapeutic targets. Studies from recent decades show that the composition, structure and function of circulating HDL are closely associated with high cardiovascular risk. A vast amount of data demonstrates that the most important mechanism through which HDL antagonizes AS involves the reverse cholesterol transport (RCT) process. Clinical trials of drugs that specifically target HDL have so far proven disappointing, so it is necessary to carry out review on the HDL therapeutics.