Theoretical analysis of RAIM in the occurrence of simultaneous two-satellite faults

Most algorithms on receiver autonomous integrity monitoring (RAIM) are under the assumption of a single-satellite fault, because there is an extremely small probability that significant simultaneous multiple-satellite faults may occur. However, after the implementation of the Galileo system in a few years, there will be more satellites in view for the user to utilise together with GPS satellites, and a combination of them will bring better performance for RAIM. On the other hand, with the help of wide area augmentation system and the use of dual-frequency operation, pseudo-range errors will be reduced greatly. Thus, tighter alert limits are required for RAIM, and formerly `small' errors should not be neglected. All of those factors make it necessary to consider simultaneous multiple-satellite faults. A detailed theoretical analysis of RAIM under the condition of two-satellite faults for both vertical and horizontal directions is presented. The characteristic/max slopes for every pair of satellites are then deduced in order to calculate the tighter vertical/horizontal protection level for RAIM     

Preparation, sintering, and microstructures of strontium barium bismuth tantalate layered perovskite ceramics

The solid solutions of Ba-doped SrBi₂Ta₂O₉ layered perovskite ceramic powders have been successfully prepared via a two-step process using BiTaO₄ as a precursor. The lattice constants of the solid solutions monotonically increase with increasing barium-ion content. The sinterability of (Sr_1–xBa_x)Bi₂Ta₂O₉ powders is significantly improved by increasing the barium-ion content. When the specimens with high barium-ion contents are sintered at 1100°C, they thermally decompose to form rod-like grains and the matrix expands, leading to a lower density. The addition of barium ions to SrBi₂Ta₂O₉ also results in significant variation in the morphology of the sintered specimens and the occurrence of c-axis preferred orientation which is ascribed to the anisotropic growth of plate-like grains. The precise control of the barium-ion content as well as the sintering conditions is critical for obtaining densified barium-ion doped SrBi₂Ta₂O₉ ceramics with a pure, layered perovskite structure.     

Piezoresistive Behavior Study on Finger‐Sensing Silicone Rubber/Graphite Nanosheet Nanocomposites

A novel finger‐sensing nanocomposite with remarkable and reversible piezoresistivity is successfully fabricated by dispersing homogeneously conductive graphite nanosheets (GNs) in a silicone rubber (SR) matrix. Because of the high aspect ratio of the graphite nanosheets, the nanocomposite displays a very low percolation threshold. The SR/GN nanocomposite with a volume fraction of conductive nanosheets closest to that for the percolation threshold presents a sharp positive‐pressure coefficient effect of the resistivity under very low pressure, namely, in the finger‐pressure range (0.3–0.7 MPa), whereby the abrupt transition could be attributed to compressive‐stress‐induced deformation of the conducting network. The super‐sensitive piezoresistive behavior of the nanocomposite is accounted for by an extension of the tunneling conduction theory which provides a good approximation to the piezoresistive effect.     

Enhancing echo cancellation via estimation of delay

The advent of packetized audio transmission, such as voice over IP (VoIP), has resulted in challenging requirements for echo cancellation technology. One key aspect of this technology is the need to characterize, quickly and accurately, the echo paths in the transmission media. Echo paths consist of a constant time delay with no echo signal and active regions in which the echo signal is present. When an adaptive filter echo cancellation algorithm is used, its performance can be greatly increased, and its complexity can be reduced if it is only applied to the active regions. This requires an algorithm to estimate the constant delay and locate the active regions. Traditionally, delay estimation has been based on direct application of cross-correlation. This method has poor performance because the input signals are highly correlated and has a high implementation cost because many cross-correlation lags have to be computed for longer time delays. The delay estimation addressed in this paper has two major advantages over the traditional methods. The first is that it has improved performance because the input signals are processed to have less correlation. The second is that the implementation cost is significantly reduced because fewer cross-correlation lags are computed, and an efficient method to estimate lags is created.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

负载型固体催化剂在生物柴油制备中的研究现状及应用前景

对生物柴油及其制备方法进行简单介绍，重点综述了负载型固体酸、碱催化剂在生物柴油制备中的研究现状，并指出当前负载型固体催化剂研制中的研究热点，最后对其应用前景了进行展望。     

用VB解决CAI中的几个问题

本文利用Windows的API函数将VB窗体前置,避免教师在CAI过程中频繁切换活动窗口,并通过VB控件将各种不同的电子文档内容在窗体中显示出来。     

MIP-CGP工艺专用催化剂CGP-1的开发与应用

阐述了生产汽油组分满足欧Ⅲ排放标准并多产丙烯的催化裂化工艺（简称MIP-CGP）专用催化剂（简称CGP-1）的研究开发与工业应用结果。CGP-1催化剂的基质具有良好的容炭性能，使活性组元受到良好保护，其优势作用在第二反应区得以充分发挥，具有更高的氢转移活性和强的汽油小分子烯烃裂化活性。中国石化九江分公司和镇海炼化公司的MIP-CGP工业试验标定结果表明，与常规FCC相比，采用CGP-1催化剂的MIP-CGP技术在生产烯烃体积分数小于18％的汽油组分的同时，丙烯产率达到8％以上。此外，汽油诱导期大幅提高，抗爆指数增加；总液体收率有所提高，干气产率下降，焦炭选择性良好。