The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

烯烃聚合单活性中心非茂催化剂的最新研究进展

综述了近几年来烯烃聚合用单活性中心非茂催化剂的研究进展。简要介绍了 2 3种由前、后过渡金属组成的配位化合物催化剂的结构与性能     

Synthesis,characterization and ion exchange properties of zirconium(IV) tungstoiodophosphate,a new cation exchanger

Zirconium(IV) tungstoiodophosphate has been synthesized under a variety of conditions. The most chemically and thermally stable sample is prepared by adding a mixture of aqueous solutions of 0·5 mol L⁻¹ sodium tungstate, potassium iodate and 1 mol L⁻¹ orthophosphoric acid to aqueous solution of 0·1 mol L⁻¹ zirconium(IV) oxychloride. Its ion exchange capacity for Na⁺ and K⁺ was found to be 2·20 and 2·35 meq g⁻¹ dry exchanger, respectively. The material has been characterized on the basis of chemical composition, pH titration, Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis. The effect on the exchange capacity of drying the exchanger at different temperatures has been studied. The analytical importance of the material has been established by quantitative separation of Pb²⁺ from other metal ions.     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

A One-Dimensional Nonlocal Damage-Plasticity Model for Ductile Materials

This paper presents a new 1-D non-local damage-plasticity deformation model for ductile materials. It uses the thermodynamic framework described in Houlsby and Puzrin (2000) and holds, nevertheless, some similarities with Lemaitre’s (1971) approach. A 1D finite element (FE) model of a bar fixed at one end and loaded in tension at the other end is introduced. This simple model demonstrates how the approach can be implemented within the finite element framework, and that it is capable of capturing both the pre-peak hardening and post-peak softening (generally responsible for models instability) due to damage-induced stiffness and strength reduction characteristic of ductile materials. It is also shown that the approach has further advantages of achieving some degree of mesh independence, and of being able to capture deformation size effects. Finally, it is illustrated how the model permits the calculation of essential work of rupture (EWR), i.e. the specific energy per unit cross-sectional area that is needed to cause tensile failure of a specimen.     

Preparation and photochromism of nanocomposite thin film based on polyoxometalate and polyethyleneglycol

A photochromic nanocomposite based on Keggin structure phosphomolybdic acid (PMoA) well dispersed in polyethyleneglycol (PEG) was fabricated. TEM image showed that PMoA nanoparticles with narrow size distribution were finely dispersed in polymer matrix. FT-IR results showed that the Keggin geometry of polyoxometalates was still preserved inside the composites and strong coulombic interaction was built between PMoA and polymer matrix. Under UV irradiation, the film was reduced photochemically to yield a blue species, which was in accordance with a charge-transfer mechanism.     

Effects of contact shape on biological wet adhesion

Wet adhesion is widely adopted in biological adhesion systems in nature. Wet adhesion is studied in this paper with the focus on the effect of different contact shapes (flat, concave, convex, and ring-like) on the adhesion force. The evolution of the liquid bridge between a fiber tip and substrate during the detaching process shows two transition points. The first transition from the radius-controlled to the contact-angle controlled process is critical to influence the strength and robustness of adhesion. We show that a concave shape is more effective than a flat one, while a convex shape has no advantage. A ring-like contact shape has advantages in a hydrophobic environment and on a rough surface.     

Dielectric behavior of Cu–GeO<Subscript>2</Subscript> cermet thin films

Capacitance and dielectric loss measurements were carried out using an Al/Cu–GeO₂/Al sandwich structure for 0 to 10 vol% Cu films, 120–400 nm thick, deposited at 0.4–1.5 nm/s in the frequency and temperature range 1–10⁶ Hz and 90–573 K, respectively. The variation of capacitance and dielectric loss with frequency and temperature follows the Goswami and Goswami model. Capacitance decreases slowly with increasing thickness and also varies with the change in deposition rate of the cermet film.