Synthesis and Application of Novel Nano Fe-BTC/GO Composites as Highly Efficient Photocatalysts in the Dye Degradation

Topics in Catalysis - Nano Fe-BTC/graphene oxide (GO) composites were successfully synthesized by hydrothermal treatment with a microwave-assisted method. Samples were characterized by X-ray...     

Similarities and differences between male and female novice designers on color‐concept associations for warnings,action required,and signs and equipment status messages

This research examined the male and female novice designers toward color associations for the concepts used for ‘warnings’, ‘action required’, and ‘signs and equipment status’ through a questionnaire‐based study. A total of 178 Hong Kong Chinese final year undergraduate design students (89 males and 89 females) participated in the study. The test used required the participants to indicate their choice of one of nine colors to associations with each of 38 concepts in a color‐concept table, so that any one color could be associated with any one of the concepts. For both male and female groups of novice designers, chi‐square tests revealed a strong color association for each concept tested in this study (P < .05). The results showed males and females agreed on some color‐concept association stereotypes which were therefore gender neutral. The male and female novice designers had the same color associations and similar levels of stereotype strengths for 21 concepts. The nine strongest and therefore most useful color‐concept association stereotypes for both male and female novice designers were: red‐danger, red‐fire, red‐hot, red‐stop, red‐emergency, red‐error, blue‐cold, blue‐male, and green‐exit. However, the male and female novice designers had different color association stereotypes for the standby (green vs. yellow), emergency exit (green vs. red), and toxic (purple vs. black) concepts, and the strengths of the 14 remaining associations for both groups were not at equivalent levels. Overall, it is anticipated that the findings of this study will act as a useful reference for novice designers and other design practitioners to optimize color coding in the design of ‘warnings’, ‘action required’, and ‘signs and equipment status’ messages.     

CuInS2/SiNWs/Si composite material for application as potential photoelectrode for photoelectrochemical hydrogen generation

This work aims at developing a new composite material based on nanosized semiconducting CuInS₂ (CIS) particles combined with silicon nanowires grown on a silicon substrate (SiNWs/Si) for photoelectrochemical (PEC)-splitting of water. The CIS particles were prepared via a colloidal method using N-methylimidazole (NMI) as the solvent and an annealing treatment. The SiNWs were obtained by chemical etching of silicon (100) substrates assisted by a metal. The CIS/SiNWs/Si composite material was obtained by deposition of an aliquot of a suspension of CIS particles onto the SiNWs/Si substrate, using spin coating followed by a drying step. The XRD pattern demonstrated that CuInS₂ grows in the tetragonal/chalcopyrite phase, while SiNWs/Si presents a cubic structure. The SEM images show semi-spherical particles (～10 nm) distributed on the surface of silicon nanowires (～10 μm). The EIS measurements reveal n-type conductivity for CIS, SiNWs/Si and CIS/SiNWs/Si materials, which could favour the oxidation reaction of water molecules.     

Migration of Point Defects in the Field of a Temperature Gradient

The influence of the temperature gradient over the thickness of the cladding of a fuel element of a fast-neutron reactor on the migration of point defects formed in the cladding material due to neutron irradiation has been studied. It has been shown that, under the action of the temperature gradient, the flux of vacancies onto the inner surface of the cladding is higher than the flux of interstitial atoms, which leads to the formation of a specific concentration profile in the cladding with a vacancy-depleted zone near the inner surface. The experimental results on the spatial distribution of pores over the cladding thickness have been presented with which the data on the concentration profiles and vacancy fluxes have been compared.     

A Giant Frequency Shift in the Raman Spectrum of Water Adsorbed on a Metallic Silver Surface

The Raman spectrum of water adsorbed on a metallic silver surface reveals an anomalously large shift of the vibrational frequency as compared to that in the bulk. The results are compared to data reported by other researchers, and possible interpretations of the observed phenomenon are discussed.     

Strain Concentration Effect in Cu–Al–Ni Single Crystals under a Longitudinal Bending Force

The behavior of a superelastic Cu?14.2% Al?4%Ni single crystal in the case of high reversible strains under a longitudinal bending force was investigated. The effect of strain confinement along the crystal length was revealed and studied. The highest reversible strains (up to 10%) were shown to be confined within the central part of the bent crystal.     

Role of Elastic Interphase Deformations in the Formation of Crystal Structure of β-Nb Particles Precipitating in a Zr–2.5% Nb Alloy

X-ray diffraction analysis has been used to study the structure of the α-Zr matrix phase and the precipitation of β-Nb particles upon the annealing of a Zr–2.5% Nb deformed alloy. It has been found that the process of the precipitation of the strengthening β-Nb particles in the alloy is accompanied by the appearance of fields of elastic interphase deformations in the matrix α phase of the alloy due to the difference in the specific atomic volumes of the crystal structures of the matrix and precipitated phases. It has been shown experimentally that, as a result of the presence of interphase deformations in the alloy, the bcc crystal structure of the precipitating β-Nb particles undergoes monoclinic distortions.     

Performance Analysis of Pulse Generators on Residual Stress of Machined Silicon Steel Using the EDM Process

The cracks in the workpiece specimens can reduce the fatigue life of any machine components. Since the residual stress has a considerable amount of influence on determining crack formation over the machined surface, it is very essential to analyze the residual stress developed in any machining process. However, it is a very tedious process to compute the residual stress over the machined surface. In the present study, an endeavor has been made to measure and analyze the residual stress of machined silicon steel as a workpiece using the EDM process with different energy distribution. The nano-indentation method was used to compute the residual stress produced over the machined surface. From the experimental results, it was found that the uniform energy distribution has produced higher compressive residual stress owing to the tiny and uniform spark energy distribution. It has also been observed that the tool electrode has a considerable amount of influence on determining development of residual stress in the EDM process.