Symmetry-breaking transitions in equilibrium shapes of coherent precipitates: Effect of elastic anisotropy and inhomogeneity

We examine the symmetry-breaking transitions in equilibrium shapes of coherent precipitates in two-dimensional (2-D) systems under a plane-strain condition with the principal misfit strain components ε* _xx and ε* _yy . For systems with cubic elastic moduli, we first show all the shape transitions associated with different values of t=ε* _yy /ε* _xx . We also characterize each of these transitions, by studying its dependence on elastic anisotropy and inhomogeneity. For systems with dilatational misfit (t=1) and those with pure shear misfit (t=−1), the transition is from an equiaxed shape to an elongated shape, resulting in a break in rotational symmetry. For systems with nondilatational misfit (−1<t<1; t ≠ 0), the transition involves a break in mirror symmetries normal to the x- and y-axes. The transition is continuous in all cases, except when 0<t<1. For systems which allow an invariant line (−1≤t<0), the critical size increases with an increase in the particle stiffness. However, for systems which do not allow an invariant line (0<t≤1), the critical size first decreases, reaches a minimum, and then starts increasing with increasing particle stiffness; moreover, the transition is also forbidden when the particle stiffness is greater than a critical value.     

IEEE Richard Harold Kaufmann Award Call for Nominations

This letter further discusses the difference between different definitions of voltage unbalance. Contrary to an earlier letter (see P. Pillay et al., ibid., vol.5, p.50-1, 2001), it is concluded that different definitions may give significantly different results. The two IEEE definitions that were not discussed in the earlier letter give different results and both deviate significantly from the true value (ratio of negative, and positive-sequence voltage) when a zero-sequence component is present.     

Intelligent identification and control for autonomous guided vehicles using adaptive fuzzy-based algorithms

Fuzzy logic was first suggested as the mechanism by which humans drive cars. This paper addresses the use of fuzzy logic and algorithms towards the intelligent autonomous motion control of land vehicles. To cope with vehicle complexities, internal parametric changes, and with unpredictable environmental effects, the controllers that are presented, whilst heuristic in nature, are self-organizing or self-learning in that they generate automatically by observation an experiential rule base that models the vehicle, and via an appropriate performance index an optimal control rule base that is robust to large parametric changes. The methodology presented is applicable to any complex process which is too difficult to model or control using conventional methods, or which has relied on the experience of a human operator. An overview of fuzzy logic and static fuzzy logic control (akin to expert systems) is provided, together with illustrative examples.     

Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Continuous phase quadrature phase shift keyed signaling techniquewith coding

A continuous phase quadrature phase shift keyed (CPQPSK) modulation technique is presented. This method utilizes a conventional QPSK modulator and a phase trajectory converter to approximate M=4, h=1/4 continuous phase signal and allows low cost, low complexity, and high rate (>1 Gbit/s) CPM modem implementation for bandwidth efficient transmission through nonlinear satellite channels. Using a communications analysis computer program it has been found that CPQPSK has 99 percent out-of-band power of 0.8R (MSK has 99 percent out-of-band power of 1.2 R where R is defined as bit rate), continuous phase trajectories, and nearly constant envelope amplitude. Simulation of realistic hardware designs indicate that the CPQPSK will require an Eb/No of 14 dB to achieve a bit error rate (BER) of 10^-6. Forward error correcting techniques using block codes with an overhead of 10 percent indicate that the Eb/No requirements can be reduced to 11.2 dB for 10^-6 BER     

Considerations in application and selection of unit substationtransformers

This paper discusses secondary unit substations transformers (USTs) ranging from 300 up through 2500 kVA with 34.5-kV maximum primary voltages and with secondary voltages 600 V and below. Pad-mounted (compartmentalized) transformers are not considered in this paper. The first part of this paper discusses USTs belonging to two general categories, liquid type and dry type (nonliquid type). Liquid types include a discussion of the presently available insulating fluids: mineral oil, high-temperature hydrocarbon fluid, silicone fluids, and the new vegetable-based fluids. Dry types include a discussion of vacuum pressure impregnated polyester, vacuum pressure encapsulated silicone, partial cast, and full cast insulation systems. The National Electric Code (1999) requirements as they affect both liquid- and dry-type USTs for both outdoor and indoor locations are considered. The paper discusses the relative advantages of each UST within each category with respect to the following: (1) first cost; (2) operating costs (losses); (3) overload capability; (4) fan cooling; (5) space factor; (6) environmental factors; (7) sound levels; and (8) maintenance