以硅氧烷醇锂为催化剂的氟硅生胶的合成

介绍了单体三氟丙基甲基环三硅氧烷通过硅氧烷醇锂催化剂聚合成氟硅生胶,讨论了不同催化剂及其用量,原料中水分含量、不同乙烯基含量对氟硅生胶分子量的影响.     

高精度智能转速测量模板的设计

介绍了一种利用高性能的16位单片机80C196KC进行转速实时高精度的测量方法，阐述了如何通过CAN总线实现与微机通讯；详细描述了硬件电路的设计，并给出了软件程序框图。     

本钢7号高炉中控室10kV供电系统技术分析及改进方案实施

根据7号高炉中控室供电状况，进行了供电平衡分析。调整两段负荷，使供电平衡安全。     

Progress of Solid Electrolytes and the Electrochemical Sensors

Four types of solid state electrochemical sensors and their general principles are introduced in the paper. The novel type-IV sensors developed in the last few years are emphasized to study hereafter. The ways to design new electrochemical sensors and the directions to develop new solid electrolytes for new electrochemical sensors are also discussed.     

Matrix expression and reachability analysis of finite automata

In this paper,we propose a matrix-based approach for finite automata and then study the reachability conditions.Both the deterministic and nordeterministic automata are expressed in matrix forms,and th...     

Multi-channel SAR imaging based on distributed compressive sensing

The rapid development of compressive sensing(CS)shows that it is possible to recover a sparse signal from very limited measurements.Synthetic aperture radar(SAR)imaging based on CS can reconstruct the target scene with a reduced number of collected samples by solving an optimization problem.For multi-channel SAR imaging based on CS,each channel requires sufficient samples for separate imaging and the total number of samples could still be large.We propose an imaging algorithm based on distributed compressive sensing(DCS)that reconstructs scenes jointly under multiple channels.Multi-channel SAR imaging based on DCS not only exploits the sparsity of the target scene,but also exploits the correlation among channels.It requires significantly fewer samples than multi-channel SAR imaging based on CS.If multiple channels offer different sampling rates,DCS joint processing can reconstruct target scenes with a much more flexible allocation of the number of measurements offered by each channel than that used in separate CS processing.     

P2P网络中的超级节点选取算法研究

P2P系统在构建覆盖网络时未考虑到与物理网络的结合,导致逻辑拓扑结构与物理拓扑结构严重不匹配问题,增加P2P相邻节点间的延迟。本文提出一种基于区域划分的超级节点选取机制,将P2P网络中的节点按照物理位置划分成若干区域,保证区域内节点在物理位置上是相近的。利用MATLAB进行仿真实验,仿真实验表明使用这种机制能降低半分布式P2P网络的信息检索延迟,有效地提高检索的效率,并且具有较好的可扩展性。     

强力输送带接头识别算法

针对现有的强力输送带故障实时检测方法存在故障定位困难的问题,以接头为基准参考点,提出了一种基于图像处理技术的强力输送带接头识别算法。该算法根据接头点的特征,把接头点用一个数值表示出来,并根据这个数值,以一种简单的方式区分出上、下接头点;然后根据接头的特征,并通过修改最长公共子序列算法的匹配方式,对接头进行识别。实际应用表明,该算法精度高、速度快,可有效识别强力输送带的接头,满足了强力输送带故障检测中接头定位的要求。     

卫星导航信号码跟踪精度理论的适用性研究

针对码跟踪精度理论在导航系统信号体制评估中的广泛应用,利用自主研发的卫星导航信号仿真平台对导航跟踪优化的适用条件进行了研究,对不同载噪比环境、前端接收带宽以及超前滞后间距条件下的信号伪距误差进行了测量,将仿真结果与理论结果对比,分析了实际应用中滤波器、鉴别器的非理想特性对信号码跟踪精度所造成的影响.仿真结果表明,在非相干超前滞后(NELP)码跟踪环的条件下,当载噪比较高时,前端接收带宽接近发射带宽,并在超前滞后间距足够小时,计算结果能够较真实的反映信号的性能,并可以为导航信号体制的理论评估以及新型导航信号的设计提供参考.