微波干燥在气相超稳Y型分子筛制备中的应用研究

研究了微波干燥在气相超稳Y型分子筛制备中的应用。结果表明，分子筛经微波干燥后，其理化性质有所改善，结晶度提高，经气相超稳化反应后其产品结构及物化性质与传统电加热干燥后的气相超稳产品基本一致，说明微波干燥可替代传统干燥方式。与传统电加热干燥方式相比，微波干燥能缩短干燥时间，有效降低能耗。     

一种用于三电平逆变器的SVPWM调制方法研究

本文从二极管箝位型三电平逆变器的基本结构出发，分析其输出状态，推导出六角形空间电压矢量图。然后从一种改进的，可以减小开关损耗，避免高的dv／dt三电平空间矢量PWM调制策略出发，建立了基于Matlab的详细仿真方案，验证了方案的可行性。文章给出了扇区判断的算法流程图，脉冲生成模块的内部结构图，其中的扇区判断的算法和脉冲生成方法对于用DSP实现三电平SVPWM具有重要的参考价值。     

DMT系统中一种易于实现的时域均衡器

总结了DMT系统中时域均衡器(TEQ)的主要设计方法，指出最大缩短信噪比(MSSNR)TEQ的最优设计方法很难实时实现。提出了一种MSSNR TEQ的次优设计方法，它首先估计出目标抽样窗的最优延迟，然后用分步求解法求出TEQ的抽头系数。和最优方法相比，次优方法的计算量大幅度减少，可实时实现，而其缩短信噪比的损失很小。仿真实验验证了次优方法的有效性。     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

阴,阳离子聚合物地层内凝胶化改善水驱效果的研究

研究了一杆阴离子聚合物（Ａｃ５３０）和一种阳离子聚合物（Ｍｂ５８１）在水溶液中形成凝胶的条件和过程、凝胶化学结构、形态、稳定性和力学性能。在模拟地层的二维微观模型内观测了两种聚合物驱替渗流、相逼、形成凝胶、凝胶封堵大孔道的机理。在亲水填砂模型内测定了阴、阳离子聚合物凝胶体系降低渗透率的能力。     

多孔板体结构足尺性能分析及材料基本要求

本文就利用诸如蛋白石这样的疏松多孔矿料同灰土构成的混合料，在路面结构中表现出的独特有效的抗冻作用机理作了深入分析，并结合足尺试验数据加以验证。阐述了所谓多孔板体结构的概念、机制和材料组成要求。     

Boole函数的线性可分性(Ⅰ)——n-维超立方体的基本理论

Boole函数的线性可分性是前向人工神经网络理论中的一个比较困难的问题之一。目前仅对变量数n≤7的某些问题给予讨论。当n≥8时,尚无判别Boole函数线性可分的一般准则,更无线性可分Boole函数的计数公式。基于此,本文详细地研究了与Boole函数线性可分性有关的n-维超立方体的基本理论,包括n-维超立方体的基本性质、超立方体中的平行线、子超立方体的计数等,并给出了构造n-维超立方体图的一种新方法。     

GaN and AlGaN high-voltage rectifiers grown by metal-organic chemical-vapor deposition

In this paper, we report the study of the electrical characteristics of GaN and AlGaN vertical p-i-n junctions and Schottky rectifiers grown on both sapphire and SiC substrates by metal-organic chemical-vapor deposition. For GaN p-i-n rectifiers grown on SiC with a relatively thin “i” region of 2 μm, a breakdown voltage over 400 V, and forward voltage as low as 4.5 V at 100 A/cm² are exhibited for a 60-μm-diameter device. A GaN Schottky diode with a 2-μm-thick undoped layer exhibits a blocking voltage in excess of ∼230 V at a reverse-leakage current density below 1 mA/cm², and a forward-voltage drop of 3.5 V at a current density of 100 A/cm². It has been found that with the same device structure and process approach, the leakage current of a device grown on a SiC substrate is much lower than a device grown on a sapphire substrate. The use of Mg ion implantation for p-guard rings as planar-edge terminations in mesageometry GaN Schottky rectifiers has also been studied.     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.