Control of Superelastic Behavior of NiTi Wires Aided by Thermomechanical Treatment with Reference to Three-Point Bending

The aim of this study is to investigate the effect of thermomechanical treatment on the superelastic behavior of a Ti-50.5 at.%Ni wire in terms of loading/unloading plateau, mechanical hysteresis, and permanent set to optimize these parameters for orthodontic applications. A new three-point bending fixture, oral cavity configuration three-point bending (OCTPB) test, was utilized to determine the superelastic property in clinical condition, and therefore, the tests were carried out at 37 °C. The results indicate that the thermomechanical treatment is crucial for thermal transformation and mechanically induced transformation characteristics of the wire. Annealing of thermomechanically treated specimens at 300 and 400 °C for 1/2 and 1 h leads to good superelasticity for orthodontic applications. However, the best superelasticity at body temperature is obtained after annealing at 300 °C for 1/2 h with regard to low and constant unloading force and minimum permanent set.     

Weld defect formation in FSWed coppers

This work was undertaken to explore the formation of weld defects in FSWed copper metals via both numerical and experimental approaches. The 4 mm-thick copper sheets were friction stir welded at a tool rotational speed of 710 rpm and tool translational speed of 40 mm/min. Microstructural evaluations were performed on the welded specimens. Also a 3D arbitrary Lagrangian Eulerian numerical model was developed to obtain temperature and material velocity profiles. To this aim, DEFORM-3D was implemented for developing the numerical simulation. Numerical results for temperature values showed good agreement with the recorded experimental data. They also suggest that on the advancing side (AS) of the trailing side, the pin velocity has the minimum amount (zero), and this is the main reason for the formation of tunneling cavity. Experimental results show that a force is created between the reminder of material at the joint and the rim of AS. This force causes a prong of surface material from the AS rim to penetrate into lower parts of weld. It seems that the inadequate pressure (low values of the plunge depth), inadequate surface materials, and the trapped air are the main causes for the formation of the weld defects.     

Direct Polyamidation in Molten Tetrabutylammonium bromide: Novel and Efficient Green Media

This is the first report of application of molten ionic liquid (MIL) for the synthesis of polyamides (PAs) from the reaction of dicarboxylic acids with diisocyanates. A fairly inexpensive and readily accessible MIL, tetrabutylammonium bromide (TBAB) was used for the synthesis of polymers. Therefore, polycondensation of terephthalic acid with various commercially available diisocyanates was performed in molten TBAB with or without dibutyltin dilaurate (DBTDL) as a catalyst. The polymerization reaction gave similar results in the presence or absence of DBTDL, indicating that, the catalyst was not needed in this process. Various PAs were obtained with high yields and moderate inherent viscosities ranging from 0.36 to 0.71 dL/g. This method was compared with the polymerization reaction in conventional solvent and in the presence of DBTDL as a catalyst. In the case of using TBAB, higher yields and inherent viscosities were obtained. This process is safe and green since toxic and volatile organic solvent such as N-methylpyrrolidone (NMP) was eliminated.     

Morphological,mechanical, and rheological studies of PVC/ABS blends in the presence of maleic anhydride

A novel method of enhancing compatibility in PVC/ABS blends is the use of ABS‐grafted‐(maleic anhydride) (ABS‐g‐MAH) as a compatibilizer. In this study, maleic anhydride was grafted onto ABS (initiated by peroxide) in an internal mixer. Grafting degree was determined by a back‐titration method, and certain amounts of the resultant ABS‐g‐MAH were added to PVC/ABS blends during their melt blending in the mixer. The weight ratio of PVC to ABS was kept at 70:30. Evaluation of compatibilization was accomplished via tensile and notched Izod impact tests, scanning electron microscopy (SEM), and rheological studies. According to the SEM micrographs, better dispersion of the rubber phase and its finer size in properly compatibilized blends were indications of better compatibility. Besides, in the presence of a proper amount [5 parts per hundred parts of PVC (php)] of ABS‐g‐MAH, PVC/ABS blends showed significantly higher impact strengths than uncompatibilized blends. This result, in turn, would be an indication of better compatibility. In the presence of 5 php of compatibilizer, the higher complex viscosity and storage modulus, as well as a lower loss modulus and loss factor in the range of frequency studied, indicated stronger interfacial adhesion as a result of interaction between maleic anhydride and the PVC‐SAN matrix. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Characterization of minocycline loaded chitosan/polyethylene glycol/glycerol blend films as antibacterial wound dressings

Wound care has been a challenging subject for medical teams and researchers. Bacterial infections are one of the most serious complications in injured skins that often affect healing process. Antibacterial wound dressings can be used to facilitate wound healing process. The purpose of this study is to fabricate chitosan (Chito)/polyethylene glycol (PEG) antibacterial wound dressing doped with minocycline, and to evaluate the influence of composition ratio on the blending properties of the films. To improve the mechanical properties of these films, we examined various amounts of glycerol as a plasticizer. Moreover, we investigated morphological and mechanical aspects, water uptake, degradation, water vapor transmission and wettability properties of the films prepared with various ratios of Chito/PEG/Gly. Assessment of mechanical properties revealed that film containing 80:20 ratio Chito/PEG with 40 PHR Gly content exhibits the highest ultimate tensile strength and elongation at break (9.74 MPa and 45.73% respectively). Furthermore, results demonstrated that upon increasing PEG and Gly contents, degradability and hydrophilicity of the films increased whereas water uptake decreased. Water vapor transmission rate of the films was close to the range of 530–1200 g/m²d, indicating that the as formed films are possible candidates for dressing low exudate wounds or burns. Minocycline loaded films exhibited a biphasic drug release profile and it was more effective on gram-positive bacteria than on gram-negative bacteria. The polymeric film with the highest amount of loaded drug (2%) exhibited insignificant cytotoxicity (88%) against normal fibroblast cell line.     

The Impact of Metastable Intermolrecular Nanocomposite Particles on Kinetic Decomposition of Heterocyclic Nitramines Using Advanced Solid‐Phase Decomposition Models

Journal of Inorganic and Organometallic Polymers and Materials - Surface oxygen of oxide catalyst has low coordination number; they are negatively charged. Surface oxygen can act active site for...     

Introducing a proper hydrogen liquefaction concept for using wasted heat of thermal power plants-case study: Parand gas power plant

A hydrogen liquefaction concept with an innovative configuration and a capacity of 4 kg·s^-1 (345.6 t·d^-1) is developed. The concept involves an ammonia absorption refrigeration system for the pre-cooling of hydrogen and MR streams from 25 ℃ to -30 ℃. The ammonia absorption refrigeration system is fed by exhaust gases of the Parand gas power plant that are normally dissipated to the environment with a temperature of 546 ℃. The simulation is performed by Aspen HYSYS V9.0, using two separate equations of state for simulating hydrogen and MR streams to gain more accurate results especially for ortho-para conversion. Results show that conversion enthalpy estimated by Aspen HYSYS, fits very well to the experimental data. Determining the important independent variables and composition of MRs are done using trial and error procedure, a functional and straightforward method for complicated systems. The minimum temperature limit in the cooling section is lowered, and an ortho-para converter is implemented in this section. The proposed concept performs well from energy aspects and leads to COP and SEC equal to 0.271 and 4.54 kW·h·kg^-1, respectively. The main advantage of this study is in the low SEC, eliminating the losses of the distribution network, and improving the ability of the hydrogen liquefaction for energy storage in off-peak times.     

Study the flashover voltage for outdoor polymer insulators under desert climatic conditions

This work presents a study of flashover voltage for outdoor polyester and composite insulators under some desert climatic conditions. Cylindrical polyester composite samples have been prepared after incorporated with different concentrations of inorganic fillers e.g., alumina trihydrate [ATH], boric acid [H₃BO₃] and magnesium hydroxide [Mg(OH)₂] to improve the electrical, mechanical and thermal properties in addition to maximize the surface flashover voltage and decrease the tracking phenomena.Results showed that flashover voltage reaches to 38 kV for samples without filler and 47 kV for samples containing 50% of ATH filler in dry condition. A comparison between inorganic fillers under various environmental conditions showed higher flashover voltage values for samples containing ATH filler than that of samples containing H₃BO₃ and Mg(OH)₂ fillers at all filler concentrations. Flashover voltage increases 24% by adding ATH filler for polyester samples under sandstorm conditions. Also, in this study, the effects of sandstorm, ultra violet (UV) radiation, mechanical strength (compressive and tensile strengths) and thermal performance with respect to surface of the sample under test have been investigated in detail.     

A comprehensive experimental evaluation of asphaltene dispersants for injection under reservoir conditions

As the efficiency of dispersants with different origins is questionable for each typical oil sample, the present study provides a reproducible and reliable method for screening asphaltene dispersants for a typical asphaltenic crude oil. Four different asphaltene dispersants (polyisobutylene succinimide, polyisobutylene succinic ester, nonylphenol-formaldehyde resin modified by polyamines, and rapeseed oil amide) were prepared and their performance on two oils from an Iranian field under laboratory and reservoir conditions was studied. A thorough analysis including ash content and SARA tests was performed on the solid asphaltene particles to characterize the nature of deposits. Then a highly efficient carrier fluid, which is crucial when injecting dispersant into the wells, was selected from a variety of chemicals by comparing their solubility. In the next step, using an optical microscope, a viscometer, and a Turbiscan, the screening of dispersants under laboratory conditions was done on a mixture of dead oil and dispersant to evaluate the onset of asphaltene precipitation and its stability when titrating by a precipitant. Finally, two different mixtures of the efficient dispersants, live oil, and carrier fluid were used with the solid detection system (SDS) and the filtration method to examine their effects on the onset pressure of asphaltene precipitation and the asphaltene content of the crude oil under reservoir conditions. The results show that the combination of experimental methods used in this work could be consistently applied to screening asphaltene dispersants. Among the four different dispersants applied here, the dispersant based on nonylphenol-formaldehyde resin modified by polyamines showed the best performance on the available live oils. This chemical modified the onset pressure of asphaltene precipitation of light oil from 4300 psi to about 3600 psi and decreased the precipitated asphaltene of heavy oil by about 30 %.     

NUMERICAL SIMULATION OF FLOW OVER TWO CIRCULAR CYLINDERS IN TANDEM ARRANGEMENT

In this article,the 2-D unsteady viscous flow around two circular cylinders in a tandem arrangement is numerically simulated in order to study the characteristics of the flow in both laminar and turbulent regimes.The method applied alternatively is based on the finite volume method on a Cartesian-staggered grid.The great source term technique is employed to identify the cylinders placed in the flow field.To apply the boundary conditions,the ghost-cell technique is used.The implemented computational method is firstly validated through simulation of laminar and turbulent flows around a fixed circular cylinder.Finally,the flow around two circular cylinders in a tandem arrangement is simulated and analyzed.The flow visualization parameters,the Strouhal numbers,and drag and lift coefficients are comprehensively presented and compared for different cases in order to reveal the effect of the Reynolds number and gap spacing on the behavior of the flow.The obtained results have shown two completely distinct flow characteristics in laminar and turbulent regimes.