Fischer–Tropsch synthesis over Co–SiO2 catalysts prepared by the sol–gel method

Fischer–Tropsch synthesis was carried out in slurry phase over uniformly dispersed Co–SiO₂ catalysts prepared by the sol–gel method. When 0.01–1 wt.% of noble metals were added to the Co–SiO₂ catalysts, a high and stable catalytic activity was obtained over 60 h of the reaction at 503 K and 1 MPa. The addition of noble metals increased the reducibility of surface Co on the catalysts, without changing the particle size of Co metal significantly. High dispersion of metallic Co species stabilized on SiO₂ was responsible for stable activity. The uniform pore size of the catalysts was enlarged by varying the preparation conditions and by adding organic compounds such as N,N-dimethylformamide and formamide. Increased pore size resulted in decrease in CO conversion and selectivity for CO₂, a byproduct, and an increase in the olefin/paraffin ratio of the products. By modifying the surface of wide pore silica with Co–SiO₂ prepared by the sol–gel method, a bimodal pore structured catalyst was prepared. The bimodal catalyst showed high catalytic performance with reducing the amount of the expensive sol–gel Co–SiO₂.     

A new quadruple therapy for the eradication of Helicobacter pylori. Effect of pretreatment with omeprazole on the cure rate

The aim of the study was to assess the speech discrimination ability of postlingually deaf adults implanted with the Combi 40 cochlear implant and to compare the results with the postoperative data published for other devices. The postoperative open and closed set speech perception performance of 21 consecutive patients was tested using a standardized test battery comprising a number, monosyllable, sentence, consonant and vowel discrimination test as well as a rhyme test in the sound only condition. Mean values achieved for each test 1, 6 and 12 months after "switch on" were evaluated. The results demonstrate that all patients have a substantial benefit from their implant and show a continuous improvement in their speech perception abilities with increased device experience. The mean percentages of correct answers after 12 months were 93.4 for numbers, 44.6 for monosyllables, 78.5 for sentences, 67.6 for the rhyme test, 59.8 for vowel, and 67.3 for consonant discrimination. Preoperatively, the mean discrimination score for monosyllables was 0%. The speech discrimination scores of our patients were similar or higher than described for similar patient groups implanted with other devices. The high stimulation rate of the implant system using the continuous interleaved speech processing strategy as well as a deep atraumatic electrode insertion into the apicalmost regions of the scala tympani may be the reason for good performance.     

Single-crystal growth and characterization of Cu2O and CuO

We have prepared a large number of crystals of cuprous oxide (Cu2O) by various procedures. Photoluminescence spectra of these crystals were studied to examine the concentration of defects, especially copper vacancy VCu to seek favourable conditions for growing Cu2O crystal. High-quality single crystals of Cu2O were prepared by the floating-zone melting method in air. Several synthetic crystals (specimens FA, FZ and GZ) and also a natural crystal were studied by X-ray analysis, inductively coupled plasma spectroscopy analysis, optical absorption, photoluminescence, photoconductivity and cyclotron resonance absorption, photoluminescence, photoconductivity and cyclotron resonance absorption to characterize their optical and electrical qualities. The best values of mobility and scattering time of photocarriers at T = 4.2 K are estimated to be h1.8 × 105 cm2 V–1 s–1 and h60 ps for positive holes, and 1.3 × 105 cm2 V–1 s–1 and 70 ps for electrons in Cu2O. Further, we report preliminary experimental results on transport property of crystals also of cupric oxide (CuO) purified by the floating-zone melting method.     

Animating Pictures of Fluid using Video Examples

We propose a system that allows the user to design a continuous flow animation starting from a still fluid image. The basic idea is to apply the fluid motion extracted from a video example to the target image. The system first decomposes the video example into three components, an average image, a flow field and residuals. The user then specifies equivalent information over the target image. The user manually paints the rough flow field, and the system automatically refines it using the estimated gradients of the target image. The user semi-automatically transfers the residuals onto the target image. The system then approximates the average image and synthesizes an animation on the target image by adding the transferred residuals and warping them according to the user-specified flow field. Finally, the system adjusts the appearance of the resulting animation by applying histogram matching. We designed animations of various pictures, such as rivers, waterfalls, fires, and smoke.     

Performance of SOR methods on modern vector and scalar processors

The building-cube method (BCM) is a new generation algorithm for CFD simulations. The basic idea of BCM is to simplify the algorithm in all stages of flow computation to achieve large-scale simulations. Calculation of a pressure field using the Successive Over Relaxation (SOR) method consumes most of the total execution time required for BCM. In this paper, effective implementations on modern vector and scalar processors are investigated. NEC SX-9 and Intel Nehalem-EX are the latest vector and scalar processors. Those processors have much higher peak performances than their previous-generation processors. However, their memory bandwidth improvement cannot catch up with the performance improvement of processors. This is the so-called memory wall problem. In our paper, we discuss optimization techniques for implementation of the SOR method based on architectural characteristics of these modern processors, and evaluate their effects on the sustained performances of these processors for BCM.     

Characterization of microbial community structures and their activities in single anaerobic granules by beta imaging, microsensors and fluorescence in situ hybridization

The spatial distribution of microorganisms and their in situ activities in anaerobic granules were investigated by fluorescence in situ hybridization (FISH), beta imaging and microsensors. FISH results revealed a layered structure of microorganisms in the granule, where Chloroflexi was present in the outermost layer, Smithella spp. and Syntrophobacter spp. were found in a depth of ca. 100 μm, and Archaea was restricted to the inner layer (below ca. 300 μm from the surface). Substrate uptake patterns elucidated by beta imaging demonstrated that glucose uptake was highest at 50 μm depth, whereas propionate uptake had a peak at 200 μm depth. In addition, microsensor measurements revealed that acid was produced mainly at 100 μm depth and H(2) production was detected at a depth from 100 to 200 μm. H(2) consumption and corresponding CH(4) production were found below 200 μm from the surface. Direct comparison of these results implied sequential degradation of complex organic compounds in anaerobic granules; Chloroflexi contributed to fermentation of organic compounds and acid production in the outermost layer, volatile fatty acids were oxidized and H(2) was produced mainly by Smithella spp. and Syntrophobacter spp. at a depth from 100 to 200 μm, and Archaea produced CH(4) below ca. 300 μm from the surface.     

Development of smart composite structures with small-diameter fiber Bragg grating sensors for damage detection: Quantitative evaluation of delamination length in CFRP laminates using Lamb wave sensing

The authors and Hitachi Cable, Ltd. have recently developed small-diameter optical fiber and its fiber Bragg grating (FBG) sensor for embedment inside a lamina of composite laminates without strength reduction. The outside diameters of the cladding and polyimide coating are 40 and 52 μm, respectively. First, a brief summary is presented for applications of small-diameter FBG sensors to damage monitoring in composite structures. Then, we propose a new damage detection system for quantitative evaluation of delamination length in CFRP laminates using Lamb wave sensing. In this system, a piezo-ceramic actuator generates Lamb waves in a CFRP laminate. After the waves propagate in the laminate, transmitted waves are received by an FBG sensor attached on or embedded in the laminate using a newly developed high-speed optical wavelength interrogation system. This system was applied to detect interlaminar delamination in CFRP cross-ply laminates. When the Lamb waves passed through the delamination, the amplitude decreased and a new wave mode appeared. These phenomena could be well simulated using a finite element analysis. From the changes in the amplitude ratio and the arrival time of the new mode depending on the delamination length, it was found that this system could evaluate the delamination length quantitatively. Furthermore, small-diameter FBG sensors were embedded in a double-lap type coupon specimen, and the debonding progress could be evaluated using the wavelet transform.     

Avoiding Routing Loops on the Internet

Suppose that some particular link in the Internet is currently congested. A natural solution is to try to make packets bypass that link. This can be done by increasing the cost of that link intentionally, say from a ₁ to a ₂, since the Internet uses shortest-path routing. Unfortunately, however, this often causes temporary loops for packet traveling, called routing loops. In this paper we show that routing loops can be avoided by increasing the cost of the link not directly from a ₁ to a ₂ but through an intermediate value, a ₃, i.e., from a ₁ to a ₃ and then to a ₂. We may need several intermediate values. We show that in this case the greedy strategy, namely, raising the cost as much as possible in each step, is optimal.     

A novel cleaning method of gold-coated atomic force microscope tips for their chemical modification

For chemical modification of gold-coated AFM tips with thiol or sulfide compounds, a new two-step precleaning procedure was studied. The two-step cleaning procedure involves (i) oxidation of organic contaminants on the AFM tips with ozone treatment and (ii) reduction of the oxidized gold surface by immersing the oxidized tip into pure hot ethanol at ca. 65 degrees C. The chemically modified tips prepared from gold-coated AFM tips precleaned by the two-step procedure gave almost the same tip characteristics as those chemically modified immediately after gold vapor deposition in a factory. The present two-step cleaning procedure can be used widely for chemical modification of commercially available gold-coated AFM tips with thiol or disulfide compounds for chemical force microscopy.     

Improvement of lysozyme recovery method from the precipitate of protein-anionic surfactant complexes

A new protein separation process using a surfactant and a polar organic solvent consists of a precipitation step and a recovery step. In the precipitation step, a protein-surfactant complex is precipitated from an aqueous solution, when an ionic surfactant, sodium di(2-ethylhexyl) sulfosuccinate (AOT), is added to an aqueous solution, including protein (lysozyme). In the recovery step, the precipitate is dissolved in a polar organic solvent, such as acetone, and the protein is recovered as precipitates when a very small amount of salt solution was added to remove surfactants from the protein-surfactant complex. However, the details of the protein recovery step from precipitate have not been studied yet. In this study, the improvement of the protein recovery step was examined from the viewpoint of a recovery ratio of protein and a remaining ratio of surfactant. The optimum NaCl concentration in the feed for the protein recovery was in the range of 0.05–0.2 kmol/m³. As the NaCl concentration in the feed increased to more than 0.2 kmol/m³, the precipitation ratio decreased due to the electrostatic screening effect of NaCl. It was found that the addition of a very small amount of NaCl solution to acetone was unnecessary when NaCl was included in the feed lysozyme solution. On the other hand, as the NaCl concentration decreased to less than 0.05 kmol/m³, the precipitation ratio was decreased due to the low re-precipitation of protein by the addition of a small amount of NaCl solution in acetone. In the case of the feed containing no salt, the desired NaCl concentration added to acetone was in the range above 0.2 kmol/m³. In addition, the most suitable volume ratio of acetone to feed was found to be 0.2.