Growth of chromium carbide in a hot wall DLICVD reactor

Chromium carbide coatings were grown at 748 K in a hot wall CVD reactor fed by sublimation of bis(benzene)chromium, BBC (MOCVD) and by direct liquid injection using a BBC/toluene solution (DLICVD). The two types of coatings exhibit an amorphous structure and the same C content (22 at.%). DLICVD permits delivering higher mass flow rate of precursors and consequently the growth rate is 3 times higher and the thickness uniformity is better than using MOCVD. Chromium metal deposition has also been investigated by DLICVD in this hot wall reactor using BBC/toluene/additive as precursor. The purpose of the additive is to block carbide formation. Two additives have been studied: (i) hexachlorobenzene (C6Cl6) and (ii) thiophenol (C6H5SH). The ratio additive/BBC required for Cr metal deposition is a few percent. In this process, C6Cl6 is not decomposed and only traces of Cl (0.4 at.%) are found in the coatings. For a ratio C6Cl6/BBC > 27% the growth of any coating is blocked. The gas phase containing C6H5SH is more reactive since the onset of deposition occurs approximately 50 K before the temperature of the chlorinated compound. Furthermore, a sulfur contamination of 3 at.% has been analyzed in the coatings revealing a partial decomposition of the additive. The results are detailed and discussed in relation with previous works.     

Neural control of posture during small magnitude perturbations: effects of aging and localized muscle fatigue

This study investigated the effects of aging and localized muscle fatigue on the neural control of upright stance during small postural perturbations. Sixteen young (aged 18-24 years) and 16 older (aged 55-74 years) participants were exposed to small magnitude, anteriorly-directed postural perturbations before and after fatiguing exercises (lumbar extensors and ankle plantar flexors). A single degree of freedom model of the human body was used to simulate recovery kinematics following the perturbations. Central to the model was a simulated neural controller that multiplied time-delayed kinematics by invariant feedback gains. Feedback gains and time delay were optimized for each participant based on measured kinematics, and a novel delay margin analysis was performed to assess system robustness. A 10.9% longer effective time delay ( p = 0.010) was found among the older group, who also showed a greater reliance upon velocity feedback information (31.1% higher differential gain, p = 0.001) to control upright stance. Based on delay margins, older participants adopted a more robust control scheme to accommodate the small perturbations, potentially compensating for longer time delays or degraded sensory feedback. No fatigue-induced changes in neural controller gains, time delay, or delay margin were found in either age group, indicating that integration of this feedback information was not altered by muscle fatigue. The sensitivity of this approach to changes with fatigue may have been limited by model simplifications.     

Development of ultrafiltration membranes from acrylonitrile co-polymers

Summary Hydrophobic polymer surfaces show higher tendency to protein adsorption and bacteria attachment, thus hydrophobic polymeric membranes foul rapidly in water purification operations. A change in membrane surface properties can reduce fouling; this may be accomplished by increasing the hydrophilicity of the membrane surface, and by using a membrane with smaller pore size. The ultrafiltration membranes were prepared via phase inversion process in our laboratory. Negatively charged hydrophilic ultrafiltration membranes were prepared from acrylonitrile-vinyl acetate (CP16)/Acrylonitrile-vinyl acetate-sodium p-sulfophenyl methallyl ether (CP24). Scanning electron microscopy (SEM) revealed the asymmetric structure of these membranes. The roughness of the surface was measured by atomic force microscopy (AFM). The basic characteristics of these membranes like water permeability, water content and membrane selectivity were also measured. Received: 29 April 2001/Revised version: 14 September 2001/Accepted: 14 September 2001     

Sustainability: ecological, social, economic, technological, and systems perspectives

Sustainability is generally associated with a definition by the World Commission on Environment and Development, 1987: "... development that meets the needs of the present without compromising the ability of future generations to meet their own needs ..." However, there is no mathematical theory embodying these concepts, although one would be immensely valuable in humanity's efforts to manage the environment. The concept of sustainability applies to integrated systems comprising humans and the rest of nature; the structures and operation of the human component (society, economy, law, etc.) must be such that they reinforce the persistence of the structures and operation of the natural component (ecosystem trophic linkages, biodiversity, biogeochemical cycles, etc.). One of the challenges of sustainability research lies in linking measures of ecosystem functioning to the structure and operation of the associated social system. We review the nature of this complex system including its ecological, social, economic, and technological aspects, and propose an approach to assessing sustainability based on Information Theory that bridges the natural and human systems. These principles are then illustrated using a model system with an ecological food web linked to a rudimentary social system. This work is part of the efforts of a larger multidisciplinary group at the U.S. Environmental Protection Agency's National Risk Management Research Laboratory.     

Forcespinning technique for the production of poly(d,l-lactic acid) submicrometer fibers: Process–morphology–properties relationship

This work addresses a systematic study for the process development and optimization of poly(d ,l -lactic acid) (PDLLA) submicrometer fibers utilizing the centrifugal spinning technique known as Forcespinning. This study analyzes the effect of polymer concentration (8, 10, and 12 wt %) and angular speed on the fiber morphology, diameter distribution, and fiber yield. The increase in polymer concentration and angular speed favored the formation of continuous and homogeneous submicrometer fibers with an absence of bead formation and higher output. The optimal conditions were established considering the morphological characteristics that exhibit a greater surface area (homogeneous and submicrometer fibers); and they were achieved at a polymer concentration of 10 wt % at an angular speed ranging from 8000 to 10 000 rpm. Optimization of PDLLA submicrometer fiber fabrication lays the groundwork for scaling up the process and serves as a platform to further develop promising applications of PDLLA nonwoven mats, particularly in the biomedical area such as in scaffolds for tissue engineering. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47643.     

Circulating endotoxin during initial antibiotic treatment of severe gram-negative bacteremic infections

The second most common cause of congenital adrenal hyperplasia is 11 beta-hydroxylase deficiency, an autosomal recessive disorder. We performed genetic analysis of CYP11B1, the gene encoding steroid 11 beta-hydroxylase, in three patients with classic 11 beta-hydroxylase deficiency. Herein we describe the first splice donor site mutation, a new nonsense mutation, and a new missense mutation in this disorder. An African-American patient was found to be a compound heterozygote for a codon 318 + 1G --> A substitution at the 5'-splice donor site of intron 5, in combination with Q356X, a nonsense mutation previously reported in an African-American patient. A Caucasian patient was found to be a compound heterozygote with a novel missense mutation, T318R, in combination with a previously reported 28-bp deletion in exon 2. A different mutation at codon 318 (T318M) has been described previously. A Caucasian patient was heterozygous for a novel nonsense mutation (Q19X) in exon 2. The second mutation was not identified in this patient. Multiple apparent polymorphisms were also observed. Two of these polymorphisms in CYP11B1 represent sequences from CYP11B2, suggesting that gene conversion may have occurred. In summary, we have identified three novel mutations and two previously reported mutations in CYP11B1 patients with 11 beta-hydroxylase deficiency. Our data suggest the presence of a mutational hot spot at codon 318 of CYP11B1, and the possibility of a founder effect in frequently identified mutations.     

产品剖析:驰骋于沙漠的无人驾驶汽车

Darpa Grand Challenge--自从各种传说中的横贯大陆的竞赛在一个世纪以前开始举办以来,从来没有哪一种令人生畏的工作能吸引如此多的工程师、教授、学生、企业团队以及汽车修理工参与其中.表面上看,它似乎是不可能被完成的.     

Development of a metric to assess the complexity of assembly/disassembly tasks in open architecture products

This paper describes two metrics to measure the complexity involved in assembly and disassembly tasks for open architecture products during its use phase. The approach proposed is based on the summary of all tasks required to assemble and disassemble a predefined set of modules to generate several product variants, which comprise different working levels or functionalities. The aim of the method is to provide a useful tool to designers in the analysis of product complexity regarding use and further phases in which the assembly and disassembly of modules are required. The benefits and usefulness of the metrics are oriented to enhance the sustainability performance of products through the measurement of complexity in modular systems for the decision-making during the design stage. The reduction of complexity involves significant benefits in all lifecycle phases of product, especially when the user or customer is responsible for many related tasks (maintenance, upgrading, reconfiguration and final disposal of modules). The metrics and their calculation process are illustrated using two case study products.     

Functional characterisation of mechanical joints to facilitate its selection during the design of open architecture products

New trends in product design require the use of modularity as key feature aimed to improve functional performance and the generation of open architecture products. For mechanical systems, one of the challenges during early design stages of these products involves the proper selection of joining methods among their constructive components. A robust joint selection process must consider product requirements, life cycle analysis and eventual procedures for assembly and disassembly. However, the general approach towards a Design-for-Assembly (DFA)/Design-for-Disassembly (DFD) only considers design, manufacturing and in some cases final disposal stage. Additionally, most of the works found in the literature are merely focused on assembly operations, disregarding economic and environmental benefits from optimising disassembly complexity. Herein, a functional characterisation of mechanical joint methods for the assembly and disassembly activities that take place throughout the product life cycle is proposed, focusing on open architecture products. Additionally, a classification of joining methods, a joint complexity metric valuation and a selection process are proposed for the conceptual design stage. The approach integrates both DFA and DFD principles in a formal methodology. The proposed selection roadmap can be implemented to increase product sustainability positively regarding resources optimisation, operational time and costs in reuse, remanufacturing and recycling tasks.