Anodic dissolution of titanium in NaCl-containing ethylene glycol

Anodic dissolution behavior of titanium in NaCl-containing ethylene glycol has been examined to obtain electropolished titanium surface. During anodic polarization in 1 mol dm^?3 NaCl ethylene glycol solution at 293 K, the titanium electrode covered with oxide dissolves with gas evolution at potentials higher than 10 V (Ag/AgCl) while it is in passive state at potentials lower than 5 V. However, after removal of the oxide layer by pre-polarization at gas-evolving potentials, no gas evolution is observed, and the titanium electrode shows a limiting dissolution current as tetravalent species at potentials higher than 5 V, producing a smooth surface. The polarization of the rotating disk titanium electrode reveals that the kinetics of the mass transfer reaction for electropolishing of titanium is controlled by titanium species dissolved into the solution, not by chloride ions or water containing in the solution. Repetition of dynamic polarization gives a well-electropolished surface.     

Preparation of nanocomposites by melt compounding polylactic acid/polyamide 12/organoclay at different screw rotating speeds using a twin screw extruder

This study analyzes the effect of different screw rotating speeds on the clay dispersion and mechanical properties of nanocomposites prepared by melt compounding polylactic acid (PLA) with an organoclay in a co‐rotating twin screw extruder. Polyamide 12 (PA12) was used as an additive. Two different screw rotating speeds, 65 rpm and 150 rpm, were used in this study. According to the tensile strength data, the Young's modulus of the PLA/clay nanocomposites showed improvement at a screw rotating speed of 150 rpm. The Young's modulus improved with the addition of the organoclay to PLA matrix, but decreased when PA12 was added to the PLA matrix. The tensile strengths and elongations become small by adding organoclay to PLA matrix. The tensile strengths of the PLA/organoclay nanocomposites increased for the higher screw rotating speed (150 rpm). The d‐spacing of PLA/PA12/Clay nanocomposites was independent of the addition of PA12. The size of the clay aggregates in the PLA/PA12/Clay nanocomposites is smaller than that of PLA/Clay. Furthermore, the thermal stability of the PLA/Clay nanocomposite increases with addition of PA12, while on the whole, it had little influence on the tensile properties. POLYM. COMPOS., 29:1–8, 2008. © 2007 Society of Plastics Engineers     

Application concepts and evaluation of small-scale catalytic combustors for natural gas

Basic application concepts of catalytic combustion are roughly classified into three types, and the development of catalysts, combustion performance and applicability are stated. On the diffusive catalytic combustion method, completeness of methane combustion and its reaction mechanism have been demonstrated by detailed combustion analysis of the burner and reaction kinetics. On the adiabatic lean premixed catalytic combustion method, applicability of a high-temperature catalyst system based on Mn-substituted hexaaluminate monolithic honeycomb to a 1.5 MW gas turbine combustor has been investigated through pressurized combustion tests and prototype engine-rig tests. As a result, a good outlook of the basic technical problems to overcome including the catalyst durability and the combustor control method was obtained, but another problem was that of the combustor capacity. In view of the progress of the non-catalytic lean premixed combustion method, it was concluded that a hybrid catalytic combustion method limiting catalytic combustion to the low-temperature range in this concept might become efficient in the future, but that it would depend on the development of efficient catalysts initiating their activity at about 350°C and having durability at 1000°C.     

Polyethylene–Carbon Nanotube Composite Film Deposited by Cold Spray Technique

Carbon nanotubes (CNTs) are high-performance materials because of their superior electrical conductivity, thermal conductivity, and self-lubrication, and they have been studied for application to polymer composite materials as fillers. However, the methods of fabricating polymer composites with CNTs, such as injection molding, are too complicated for industrial applications. We propose a simple cold spray (CS) technique to obtain a polymer composite of polyethylene (PE) and CNTs. The composite films were deposited by CS on polypropylene and nano-porous structured aluminum substrates. The maximum thickness of the composite film was approximately 1 mm. Peaks at G and D bands were observed in the Raman spectra of the films. Scanning electron microscopy images of the film surface revealed that PE particles were melted by the acceleration gas and CNTs were attached with melted PE. The PE particles solidified after contact with the substrate. These results indicate that PE–CNT composite films were successfully deposited on polypropylene and nano-porous structured aluminum substrates by CS.     

Very high temperature annealing effect on amorphous carbon films grown on refractory oxide substrates by pulsed laser deposition

We have carried out very high temperature heat treatment at 1400–2700 °C of about 10 nm-thick amorphous carbon thin films deposited on refractory substrates MgO, Al₂O₃, and yttria-stabilized zirconia (YSZ) using pulsed laser deposition techniques. After the annealing, a few nanometer scale sp² crystallization of the films and a large corrugation with a height of more than 1 μm were observed by Raman spectroscopy analysis and optical/atomic force microscopes, respectively. The corrugation is probably caused by the formation of gases at the film/substrate interface during the heat treatment.     

Depassivation-repassivation behavior of a pure iron surface investigated by micro-indentation

Depassivation-repassivation behavior on a pure iron surface in borate buffer solution was examined under potentiostatic control by a micro-indentation test. Current peaks emerge during both downward and upward drives of the indenter due to depassivation which is caused by plastic deformation of the substrate but not elastic deformation and repassivation. The total electric charge of the current peaks is proportional to the maximum load. The total electric charge also increases with increase in intermission time of the indentation, indicating that the passive film is ruptured even during stress relaxation. It is estimated from the electric charge balance that 82% and 18% of the film rupture occurs during the downward drive and intermission, respectively, and that no rupture occurs during the upward drive. Furthermore, the film-ruptured area is estimated to be 80% of the plastic deformed surface area. The partial retainment of the passive film on iron suggests that the ductility of the passive film is higher than that of the substrate.     

Experimental analyses for electronic structure of barium zirconate-strontium zirconate proton-conducting solid solution

In proton-conducting oxides, analyses for their electronic structure contribute to the understanding of interactions between defects in them. In this study, electronic band alignment of (1−x)BaZr_0.8Y_0.2O_3−δ(BZY)–xSrZr_0.95Y_0.05O_3−δ(SZY) proton-conducting solid-solution system (BSZY) which has high defect concentration and the deep valence band is experimentally investigated. By using thin-film specimens for optical absorption measurements, absorption edges derived from electron transition from the valence band to the conduction band which was insensitive to the proton incorporation were clearly observed in spite of the high defect concentration. The obtained optical band gap energy increased from 5.61 to 5.89 eV with increasing x, which was consistent with a composition dependence of Zr(Y)O₆ octahedral tilting. Ultraviolet photon-yield spectroscopy (UV-PYS) measurements under vacuum condition revealed that BZY and SZY had ionization energy of 6.98 and 7.31 eV, respectively, and thus the absolute energy levels of the valence band maximum and the conduction band minimum of BSZY were experimentally clarified. We propose that the combination of the optical absorption measurements using thin-film specimens and the UV-PYS measurements under vacuum condition is effective in evaluating fundamental electronic structures of proton-conducting oxides.     

Pervaporation via silicon-based membranes: Correlation and prediction of performance in pervaporation and gas permeation

Pervaporation (PV) is a membrane technology that holds great promise for industrial applications. To better understand the PV mechanism, PV dehydrations of various types of organic solvents (methanol, ethanol, iso-propanol, tert-butanol, and acetone) were performed on five types of organosilica and two types of silicon carbide-based membranes, all with different pore sizes. Water permeance was dependent on the types of organic aqueous solutions, which suggested that organic solvents penetrated the pores and hindered the permeation of water. In addition, water permeance of various types of membranes in PV was well correlated with hydrogen permeance in single-gas permeation. Furthermore, a clear correlation was obtained between the permeance ratio in PV and that in single-gas permeation, which was confirmed via the modified-gas translation model. These correlations make it possible to use single-gas permeation properties to predict PV performance.     

Enhancement of Anti-Tumoral Immunity by β-Casomorphin-7 Inhibits Cancer Development and Metastasis of Colorectal Cancer

β-Casomorphin-7 (BCM) is a degradation product of β-casein, a milk component, and has been suggested to affect the immune system. However, its effect on mucosal immunity, especially anti-tumor immunity, in cancer-bearing individuals is not clear. We investigated the effects of BCM on lymphocytes using an in vitro system comprising mouse splenocytes, a mouse colorectal carcinogenesis model, and a mouse orthotopic colorectal cancer model. Treatment of mouse splenocytes with BCM in vitro reduced numbers of cluster of differentiation (CD) 20⁺ B cells, CD4⁺ T cells, and regulatory T cells (Tregs), and increased CD8⁺ T cells. Administration of BCM and the CD10 inhibitor thiorphan (TOP) to mice resulted in similar alterations in the lymphocyte subsets in the spleen and intestinal mucosa. BCM was degraded in a concentration- and time-dependent manner by the neutral endopeptidase CD10, and the formed BCM degradation product did not affect the lymphocyte counts. Furthermore, degradation was completely suppressed by TOP. In the azoxymethane mouse colorectal carcinogenesis model, the incidence of aberrant crypt foci, adenoma, and adenocarcinoma was reduced by co-treatment with BCM and TOP. Furthermore, when CT26 mouse colon cancer cells were inoculated into the cecum of syngeneic BALB/c mice and concurrently treated with BCM and TOP, infiltration of CD8⁺ T cells was promoted, and tumor growth and liver metastasis were suppressed. These results suggest that by suppressing the BCM degradation system, the anti-tumor effect of BCM is enhanced and it can suppress the development and progression of colorectal cancer.     

Excess estrogen sulfoconjugation as the possible cause for a poor sign of parturition in pregnant cows carrying somatic cell clone fetuses

We conducted this study to elucidate a factor causing a poor sign of parturition and prolonged gestation, which is frequently observed in cows carrying somatic clone fetuses. Pre-partum rises in concentrations of plasma estrone and estradiol-17beta in the recipient cows pregnant with clones were subtle. By contrast, the plasma concentration of estrone sulfate in clone pregnancies increased gradually from pre-initiation of parturition induction whereas control cows that received in vivo-derived embryos showed a significant increase at parturition. Therefore, in clone pregnancies, the ratio of estrone/estrone sulfate was low during the pre-partum period compared with control. Messenger RNA expression of estrogen sulfotransferase (SULT1E1) in the placenta at parturition was significantly higher in clone pregnancies than control pregnancies and was localized in binucleate cells (BNC). SULT1E1 mRNA abundance was negatively and positively correlated with concentrations of maternal estrone and estrone sulfate at parturition respectively. Messenger RNA expressions of estrogen sulfatase (STS) and aromatase (CYP19) were similar between clone and control pregnancies and were localized in BNC and caruncular epithelial cells. STS and CYP19 mRNA abundances showed positive correlations with maternal estradiol-17beta concentration. The population of BNC in the placenta did not differ between clone and control pregnancies. Plasma cortisol concentration of vaginally delivered newborn clone calves was comparable with those of control, although cesarean section delivered clone calves showed a low concentration. These results suggest that excess estrogen sulfoconjugation is the reason for the perturbed low ratio of active to inactive estrogens and the resulting hormonal imbalance contributes to the lack of overt signs of readiness for parturition in cows pregnant with clones.