Effect of nitrogen and nickel on the stability of an Fe-12Cr-23Mn austenitic steel

The effect of nitrogen and nickel on the austenite stability and the structural changes as a result of cold work of an Fe-12Cr-23Mn alloy steel has been examined by transmission electron microscopy and X-ray analysis. Prestrain was performed either at room temperature or at 200° C. Final strain was carried out at liquid nitrogen temperature. The volume fraction of strain-induced martensite decreased by 40% and 12% due to the addition of 2.43% Ni and 0.11% N, respectively, despite whether prestrain was performed or not. The mechanisms are discussed in terms of the phase, stacking faults, dislocation cells and dislocation tangles induced by prestrain and final strain.     

低电压氧化锌压敏电阻器的研究

研究了一种制造低电电压氧化锌压敏电阻器的方法。在基本成分的基础上适当加入二氧化钛可降低梯度电压（Ｖ１ｍＡ／ｍｍ），适量掺硼和改进热处理工艺可减小元件的漏电流和提高其稳定性。     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

环己烷液相无催化剂的氧化动力学研究

采用搅拌釜反应器,在确认已排除传质因素对反应速率影响的情况下,研究了环己烷液相无催化剂的氧化反应动力学。应用自由基理论及最优化计算技术,从导出的8个候选动力学模型中,确定了最佳的动力学模型,它能满意地描述环已烷氧化过程。该动力学可为环己烷氧化工业生产操作条件的优化、反应器的选型及工业设计提供依据。     

Poly(3‐chlorothiophene) films prepared by the direct electrochemical oxidation of 3‐chlorothiophene in mixed electrolytes of boron trifluoride diethyl etherate and sulfuric acid

3‐Chlorothiophene (CT) was electrochemically polymerized in mixed electrolytes of a boron trifluoride diethyl etherate solution containing 0–20% (by volume) sulfuric acid. The oxidation potentials of the monomer in these media were measured to be only 1.06–1.31 V (vs Ag/AgCl). These values were much lower than that of CT in acetonitrile and 0.1 mol/L (Bu)₄NBF₄ (1.92 V vs Ag/AgCl). Poly(3‐chlorothiophene) (PCT) films with conductivities of 0.1–2 S cm^?1 were obtained. The structure, morphology, and electrochemical behavior of the PCT films also were investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 502–509, 2003     

炭黑填充硬聚氯乙烯的改性

为使聚氯乙烯具有抗静电性能,采用加入具有导电性填料的方法,但加入大量的填料,会使硬聚氯乙烯的冲击性能降低,加工性能变差。本文是在以炭黑为填料的基础上,研究不同的改性剂和加工助剂改进硬聚氯乙烯的效果,结果表明,加入冲击改性剂和加工助剂后,大大增加了硬聚氯乙烯的冲击强度,且加工性能也得到改善,同时由于炭黑具有补强效果,其拉伸强度和弯曲强度在加入改性剂后也能满足使用要求。     

炭分子筛概述

阐述了炭分子筛分离的原理，并分别从其制备原料、制备方法、产品用途等方面综述了近年来炭分子筛的新进展。     

开机日志错误

正Q:我的Windows 8系统中之前安装了百度杀毒,卸载后发现开机日志中总有错误显示"Bhbase,Bnbase,Bndef,Bprotect",开机速度变慢。请问这该如何处理?A:从http://tinyurl.com/mkapkk5下载安装微软的Autoruns工具,然后搜索Bhbase、Bnbase、Bndef及Bprotect,找到后直接将这些项删除即可。     

油水井化学封窜堵漏新工艺

通过分析中原油田注水开发的两大问题，阐明了新型堵剂YLD-1的适应性，结合室内试验，重点分析了该堵剂的性能特点，深入探讨了封窜堵漏的选井原则和施工工艺，经过在文留油田的现场应用，展示了该技术良好的发展前景。