Materials balance in a tung oil mill

Summary Weights were determined and analyses made of tung fruit milled and of all products leaving the mill for two runs of about 90 tons each in a commercial mill under normal operating conditions. Dry matter, oil, and nitrogen in the fruit were satisfactorily accounted for in products leaving the mill, 101% of the oil being accounted for in each run. This showed that the methods of analysis and sampling were accurate. Losses occurred principally in particles of kernels occluded with the hulls and in the screw-press cake. Seventy-eight and 82% of the oil in the fruit was recovered as filtered oil. Repressing the filter-press cake by adding it back to the stream of ground nuts just before they entered the screw-presses was not proven to be economical as at the end of the run just as much cake was on hand, and it had as high an oil content as if no filter cake had been fed back through the screw presses. Only about half as much oil could be filtered per filtration cycle, resulting in an increase in cost of labor and a decrease in filtering capacity. The apparent oil content of the screw-press cake decreases by about 2% after four to eight days as compared to its apparent oil content at the time of pressing because of polymerization. Thus, screw-press cake samples should be analyzed for oil as soon as possible after extrusion. Both of these laboratories are maintained by the Agricultural Research Service of the U. S. Department of Agriculture.     

Large scale diesel driven vapor compression units

A hybrid plant consisting of a diesel driven vapor compression unit and a steam ejector - vapor compression MES unit will have a very low specific primary energy consumption.This paper discusses results of experiments concerning critical parts of such a concept as well as some results of numerical calculations.The experiments were expecially concerned with brine distribution by sieve trays in the MES-unit and with the behaviour of such units under different but steady state load conditions     

Impedance spectroscopy study of hardened Portland cement paste

In this paper, the differential impedance analysis (DIA) has been applied to the study of the dielectric properties of hardened Portland cement paste. Two time constants are found in the impedance spectra obtained in the frequency region form 100 kHz to 15 MHz. One time constant has been attributed to the solid matrix and the other one to the liquid phase filling the pores. The effect of the cement paste-electrodes interface has been quantified using two different experimental set-ups. Measurements using direct contact between electrodes and cement paste have been compared with measurements using an air gap technique in which the specimen “floats” between the electrodes. The two referred time constants have been found in both types of measurements. The influence of drying on the dielectric parameters is also studied.     

Some theorems of the eddy-current theory

Contents In the paper, theorems for the electric vector potentialT and magnetic scalar potentialU are discussed, which occur in the boundary-value problems for eddy currents induced in a conducting block by an external magnetic field. Uniqueness of the solution is examined. An integral representation of the scalar potentialU is derived for a nonmagnetic conductor. It is shown that for a thin metallic shell the integrodifferential equation results from general formulas related to the block.

---

Einige Theoreme der Wirbelstromtheorie

Übersicht In der Arbeit werden drei Theoreme für das elektrische VektorpotentialT und das magnetische SkalarpotentialU beschrieben, die in den Randwertaufgaben für in einem metallischen Block durch das äußere magnetische Feld induzierte Wirbelströme auftreten. Es wird bewiesen, daß eine solche Randwertaufgabe eine eindeutige Lösung hat, wenn das Vektorpotential auf dem Rand gleich Null ist. Eine Integralrepräsentation des Skalarpotentials wird abgeleitet. Es wird gezeigt, daß die Integrodifferentialgleichung für eine dünne metallische Hülle aus allgemeinen, den Block betreffenden Formeln hervorgeht.

---

List of principal symbols e coordinate unit vector - H magnetic intensity - J current density - T electric vector potential - U magnetic scalar potential - permeability - conductivity - V boundary of regionV     

Multifunctional foam glasses from volcanic glassy rocks

Translated from Steklo i Keramika, No. 1, pp. 5–6, January, 1991.     

Derivation and analysis of a filtered backprojection algorithm for cone beam projection data

The authors address the problem of three-dimensional image reconstruction from cone beam projections. Modifying a result due to A.A. Kirillov (Soviet Math. Dokl., vol. 2, p.268-9, 1961), the authors derive an inversion formula for the case where the cone vertices form an unbounded curve. For the special case in which the cone vertices form a circle, an approximate reconstruction formula is developed and shown to be essentially equivalent to the practical cone-beam algorithm of L.A. Feldkamp et al. (1984). For this approximate inverse, the authors derive the resulting spatially varying point spread function, examine the effect of bandlimiting due to sampling, and compare the resulting image quality as a function of the radius of the circle formed by the cone vertices.     

Infrared reflectance and transmission spectra of semiconducting non-stoichiometric CdGe x As2

The infrared reflectance and transmission spectra of amorphous CdGe _x As₂ were investigated to study the amorphous structure with varying Ge content. The mid-infrared optical absorption edges of amorphous CdGe _x As₂ with 0<x<1.2, were observed in the range 1.6–1.7 m, indicating a structural similarity in short-range order throughout. Comparing the reflectance and transmission spectra of amorphous and devitrified crystalline phases established that the structures of amorphous CdGe _x As₂ transformed from the CdAs₂ basic structure to the chalcopyrite (CdGeAs₂) structure, as one progressed fromx=0 tox=1.2. The infrared spectra were interpreted interactively with radial distribution function, magnetic susceptibility, density measurements, and crystallization studies. The crystallization behaviour of amorphous CdGe _x As₂ that was heat treated at different temperatures was investigated using far-infrared transmission spectra.     

Metalloorganic solution deposition of ferroelectric PZT films

The metallo-organic solution deposition (MOSD or sol-gel) technique can be used for preparing lead zirconate titanate (PZT) ceramics with a wide range of compositions and crystal structures for electrooptical applications. Film morphology is affected by the stoichiometry of the film, hydrolysis and polymerization of the sol-gel solution, and thermal treatment of the deposited material. The lattice parameter decreases with the amount of titanium in the PZT, in agreement with ceramic data. A slight initial excess of lead in the coating solution is found to improve film morphology. Unlike traditional powder ceramic processing techniques, MOSD permits the growth of small uniform grains that are conducive to achieving consistent electronic and optical properties. Results show that the properties of films prepared by the MOSD process can be tailored to meet the needs of device applications.     

Thermophysical properties of a Ti–44%Al–8%Nb–1%B alloy in the solid and molten states

The families of titanium aluminide intermetallic alloys have attractive high temperature mechanical properties which make them potential candidate materials for a wide range of applications, particularly in the aeronautic and automobile sectors. The development of appropriate manufacturing techniques is an essential stage in the engineering exploitation of these materials, e.g., Induction Skull Melting is one of the techniques which needs to be optimised for the casting of titanium aluminides. Research is underway to develop a computer model of this process but data are required for the key thermophysical properties. Pulse-heating techniques have been used to measure properties for the Ti–44Al–8Nb–1B system. Rectangular samples have been prepared and are resistively heated as part of a fast capacitor discharge circuit. Time-resolved measurements with sub-μs resolution of currents through the specimen were made with a Pearson probe current monitor using the induction principle. Voltages across the specimen were determined with knife-edge contacts and voltage dividers, and radiance temperatures of the sample were measured with a pyrometer. These measurements allow the calculation of specific heat and dependencies between enthalpy, electrical resistivity and temperature of the alloy up into the liquid phase. Data for thermal diffusivity have been obtained by using the Wiedeman–Franz relation. The results are compared with those obtained using DSC and the four-probe method to measure the temperature dependence of the resistivity.