Nitric oxide reduction and carbon monoxide oxidation over carbon-supported copper-chromium catalysts

Carbon supported copper-chromium catalysts are shown to be very active for both the reduction of nitric oxide with carbon monoxide and the oxidation of carbon monoxide with oxygen. Mixed copper-chromium oxide active phases have good activity in the simultaneous removal of nitric oxide and carbon monoxide from exhaust gases. The influence of several catalyst variables has been investigated. The activity per volume of catalyst increases with increasing loading, while the intrinsic activity shows a maximum around C/M=100−50. An optimum catalyst for nitric oxide reduction and carbon monoxide oxidation has a copper/chromium ratio of 2/1. The apparent activation energy for the carbon monoxide oxidation over carbon supported copper-chromium catalysts is 77 kJ/mol, suggesting that the Cu---O bond rupture is the rate-limiting process. The reduction of nitric oxide takes place at higher temperatures. Since all catalysts have a low selectivity for molecular nitrogen formation at lower temperatures, the dissociation of nitric oxide is probably rate determining, resulting in a slightly reduced catalyst system. In an excess of carbon monoxide the reaction is first-order in nitric oxide and zero-order in carbon monoxide. Moisture inhibits the reaction by reversible competitive adsorption, whereas carbon dioxide does not. Oxygen completely inhibits the reduction of nitric oxide due to the more rapid reoxidation of the catalytic sites compared to nitric oxide. Therefore, the reduction of nitric oxide takes place only when all oxygen has been converted and, hence, is shifted to higher temperatures. As a possible consequence, the production of nitrous oxide is reduced. Nitric oxide and molecular oxygen react preferentially with carbon monoxide, so, in an excess of oxidizing component, gasification of the carbon support occurs at higher temperatures after carbon monoxide has been completely consumed.     

Afterburner [network-independent card for protocols]

Many current implementations of protocols such as the Transmission Control Protocol/Internet Protocol (TCP/IP) are inefficient because data are often accessed more frequently than necessary. Three techniques that reduce the need for memory bandwidth are proposed. The techniques are copy-on-write, page remapping, and single-copy. Afterburner, a network-independent card that provides the services that are necessary for a single-copy protocol stack, is described. The card has 1 MByte of local buffers and provides a simple interface to a variety of network link adapters, including HIPPI and asynchronous transfer mode (ATM). Afterburner can support transfers to and from the link adapter card at rates up to 1 Gbit/s. An implementation of TCP/IP that uses the features provided by Afterburner to reduce the movement of data to a single copy is discussed. Measurements of the end-to-end performance of Afterburner and the single-copy implementation of TCP/IP are presented     

The evolution of custom microarray manufacture

Given the enormous size of the genome and that there are potentially many other types of measurements we need to do to understand it, it has become necessary to pick and choose one's targets to measure because it is still impossible to evaluate the entire genome all at once. What has emerged is a need to have rapidly customizable microarrays. There are two dominant methods to accomplish custom microarray synthesis, Affymetrix-like microarrays manufactured using light projection rather than semiconductor-like masks used by Affymetrix to mass manufacture their GeneChip/sup TM/ arrays now, or the ink-jet printing method employed by Agilent. The manufacture of these custom Affymetrix-like microarrays can now be done on a digital optical chemistry (DOC) machine developed at the University of Texas Southwestern Medical Center, and this method offers much higher feature numbers and feature density than is possible with ink-jet printed arrays. On a microarray, each feature contains a single genetic measurement. The initial DOC prototype has been described in several publications, but that has now led to a second-generation machine. This machine reliably produces a number of arrays daily, has been deployed against a number of biomedical questions, is being used in new ways and has also led to a number of spin-off technologies.     

Climatic solar roof: an ecological alternative to heat dissipation in buildings

A new system based on the harnessing of solar and wind power is presented for heat dissipation in air conditioning facilities. The innovation offered by the new system is the integration of two well-known subsystems: a cooling tower and a solar chimney which increases the air flow without the use of electric power. The system is described and presented together with a model for its study. The field data acquired from the prototype built in southern Spain establishes the actual potential of the system, which provides a new approach to a sustainable technological development.     

Measurements of single chain form factors by small-angle neutron scattering from polystyrene blends containing high concentrations of labelled molecules

A series of small angle neutron scattering measurements on blends of normal polystyrene (PSH) and labelled (deuterated) polystyrene (PSD) have been made with concentrations of PSD from 5 to 50 mol %. It is shown that the single chain form factor of the polymer in bulk can be obtained from a single concentration measurement for any concentration of labelled molecules, providing the molecular weights of the parent and labelled molecules are the same and the molecular weight distributions are narrow.     

Functional Properties and Food Applications of Rapeseed Protein Concentrate

Rapeseed protein concentrate (RC), prepared with 2% hexameta-phosphate, was tested for its functionality and performance in some foods. The RC had good nitrogen solubility, fat absorption, emulsification, and whipping capacities but poor water absorption and gelling properties. It increased the emulsion stability, and protein but lowered the fat content of wieners. It also increased the cooking yield, reduced the shrinkage and tenderized meat patties. Results were similar to soybean isolate except for the poorer color and flavor. The cooking yield of RC supplemented wieners was less than the all-meat control and soybean-supplemented wieners. A 9% RC dispersion mixed with an equal volume of eggwhite produced a meringue of comparable stability and texture to that of eggwhite alone.     

Polymeric schiff's base chelates and their precursors 8a), some cobalt chelates as catalysts for the isomerization of quadrycyclane to norbornadiene

Summary Starting with Z-2, 3-diamino-2-butenedinitrile as diamine component the synthesis of the low molecular N,N,O,O-chelate 3.Co and its ligand 3 is optimized. An easy synthesis of the chelate 8.Co covalently bound on macroreticular resins is presented. The chelates 8.Co are the most active heterogenous catalysts for the valence isomerization of quadricyclane to norbornadiene today.     

Removal of nitrates from groundwater through the use of artificial wetlands

Intensive fertilizer use has led to nitrate contamination of groundwater in many areas. This article examines the possibility of removing nitrates through the construction of artificial wetlands. A pilot study conducted in Denmark has found that the method is effective and economical, at least for small waterworks, though further treatment is necessary before an acceptable microbiological water quality is attained.     

What's different about Six Sigma?

The Six Sigma approach is one of the more recent initiatives adopted by organisations who seek to make a paradigm shift in performance improvement (attacking at least one of the cost, quality, delivery measurements for improved competitiveness). Is there anything new about Six Sigma, does it offer improvements that other approaches cannot, or is it just a clever delivery of repackaged goods? The author investigates the above questions related to the Six Sigma approach     

Discussion of "Hybrid-secondary-uncluttered induction (HSU-I)machine" [and closure]

J. Perahia comments on the paper by J. S. Hsu (see ibid., vol.16, p.192-7, 2001) and expands on the case of a two stator three phase squirrel cage induction machine where one stator housing is stationary and other stator housing is mounted on a worm gear assembly. The original author replies to the comments