Oxidation of atmospheric humic like substances by ozone: a kinetic and structural analysis approach

This work explores the heterogeneous reaction between HUmic-LIke Substances (so-called HULIS) and ozone. Genuine atmospheric HULIS were extracted from aerosol samples collected in Chamonix (France) in winter and used in coated flow tube experiments to evaluate heterogeneous uptake of O? on such mixtures. The uptake coefficient (γ) was investigated as a function of pH (from 2.5 to 10), O? concentration (from 8 to 33 × 1011 molecules cm?3), relative humidity (20 to 65%) and photon flux (from 0 to 1.66 × 101? photons cm?2 s?1). Reactive uptake was found to increase in the irradiated experiment with pH, humidity and photon flux. The extract was characterized before and after exposure to O? and/or UV light in the attempt to elucidate the effect of the photochemical aging. Carbon content measurements, UV-vis spectroscopy and functional groups analysis revealed a decrease of the UV absorbance as well as of the carbon mass content, while the functionalization rate (COOH and C═O) and therefore the polarity increased during the simulated photochemical exposure.     

A low power consumption CMOS differential-ring VCO for a wireless sensor

This paper describes a new three-stage voltage controlled ring oscillator (VCO) based on 0.35???m standard CMOS technology. The VCO was designed for a transmitter operating in the 863?C870?MHz European band for wireless sensor applications. The transmitter is designed for binary frequency-shift keying (BFSK) modulation, communicating a maximum data rate of 20?kb/s. In addition to the VCO, the transmitter combines a BFSK modulator, an up conversion mixer, a power amplifier and an 863?C870?MHz band pass filter. The modulator uses the frequency hopping spread spectrum and it is intended for short range wireless applications, such as wireless sensor networks. The oscillation frequency of the VCO is controlled by a voltage V_CTRL. Simulation results of the fully differential VCO with positive feedback show that the estimated power consumption, at desired oscillation frequency and under a supply voltage of 3.3?V, is only 7.48?mW. The proposed VCO exhibits a phase noise lower than ?126?dBc/Hz at 10?MHz offset frequency.     

Nonlinear viscoelastic properties of tissue assessed by ultrasound

A technique to assess qualitatively the presence of higher-order viscoelastic parameters is presented. Low-frequency, monochromatic elastic waves are emitted into the material via an external vibrator. The resulting steady-state motion is detected in real time via an ultra fast ultrasound system using classical, one-dimensional (1-D) ultrasound speckle correlation for motion estimation. Total data acquisition lasts only for about 250 ms. The spectrum of the temporal displacement data at each image point is used for analysis. The presence of nonlinear effects is detected by inspection of the ratio of the second harmonics amplitude with respect to the total amplitude summed up to the second harmonic. Results from a polyacrylamide-based phantom indicate a linear response (i.e., the absence of higher harmonics) for this type of material at 65 Hz mechanical vibration frequency and about 100 microm amplitude. A lesion, artificially created by injection of glutaraldehyde into a beef specimen, shows the development of higher harmonics at the location of injection as a function of time. The presence of upper harmonics is clearly evident at the location of a malignant lesion within a mastectomy.     

Ion beam sputtering coatings on large substrates: toward an improvement of the mechanical and optical performances

Large mirrors (?350 mm) having extremely low optical loss (absorption, scattering, wavefront) were coated for the VIRGO interferometer. The new generation of mirrors needs to have a better wavefront and lower mechanical loss. To improve the component wavefront, the corrective coating technique was used. By doping the tantalum pentoxide layers, we improved, for the first time to our knowledge, the multilayer mechanical loss. The first results are discussed.     

Practical constraints in the kinetic plot representation of chromatographic performance data: theory and application to experimental data

It is demonstrated that the kinetic plot representation of experimental plate height data can also account for practical constraints on the column length, the peak width, the viscous heating, and the mobile-phase velocity without needing any iterative solution routine. This implies that the best possible kinetic performance to be expected from a given tested support under any possible set of practical optimization constraints can always be found using a directly responding calculation spreadsheet template. To show how the resulting constrained kinetic plots can be used as a powerful design and selection tool, the method has been applied to a series of plate height measurements performed on a number of different commercial columns for the same component (butyl-parabene) and mobile-phase composition. The method, for example, allows one to account for the fact that the advantageous solutions displayed by the silica monolith and 5 microm particle columns in the large plate number range of the free kinetic plot are no longer accessible if applying a maximal column length constraint of Lmax = 30 cm. In the plate number range that remains accessible, the investigated sub-2 mum particle columns in any case perform (at least for the presently considered parabene separation) better than the 3.5 mum particle columns or silica monolith, especially if considering the use of system pressures exceeding 400 bar. The constrained kinetic plot method can also be used to select the best-suited column length from an available product gamma to perform a separation with a preset number of plates. One of the optimization results that is obtained in this case is that sometimes a significant gain in analysis time can be obtained by selecting a longer column, yielding the desired plate number at a larger velocity than that for a shorter column.