Laccase‐catalyzed synthesis of polypyrrole‐multiwalled carbon nanotube composites as energy storage materials for capacitors

Multiwalled carbon nanotubes (MWNTs) were coated with polypyrrole (PPy) using in situ enzymatic polymerization of pyrrole catalyzed by a laccase (benzenediol:oxygen oxidoreductase, EC 1.10.3.2) from Trametes versicolor. Transmission electron microscopy revealed that the MWNTs were uniformly coated with very thin layers of PPy without any indication of globular polymer aggregate formations. The enzymatic synthesis of the MWNTs/PPy composites was quite simple being performed in a one‐pot aqueous solution (pH 4.0) under mild reaction conditions. The potential of the composites with respect to the development of energy storage devices was demonstrated by fabricating a two‐electrode coin cell capacitor (diameter 20 mm, thickness 1.6 mm) utilizing the composites as electrode materials. The capacitance of the cell was 28.0 F g^?1 for the electrode material as measured by a galvanostatic charge–discharge method. The energy density and power density were 2.55 and 805 W kg^?1, respectively, which were close to those of the capacitors classified as ultracapacitors. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43307.     

ZSM-5 Supported Cobalt Catalyst for the Direct Production of Gasoline Range Hydrocarbons by Fischer–Tropsch Synthesis

Abstract  

Fischer–Tropsch synthesis (FTS) reaction for the direct production of gasoline range hydrocarbons (C₅–C₉) from syngas was investigated on cobalt-based FTS catalyst supported on the ZSM-5 possessing a four different Si/Al ratio. The FTS catalysts were prepared by impregnation method using cobalt nitrate precursor in a slurry of ZSM-5, and they were characterized by surface area, XRD, H₂-TPR and NH₃-TPD. Cobalt supported catalyst on ZSM-5 having a low Si/Al ratio of 15 was found to be superior to the other catalysts in terms of better C₅–C₉ selectivity due to the formation of small cobalt particle and the presence of larger number of weak acidic sites. It also exhibited the highest catalytic activity because of the higher reducibility and the small cobalt particle size.     

Immobilization of laccase on carbon nanomaterials

Laccase from Trametes versicolor was readily immobilized on carbon nanomaterials including multiwalled carbon nanotubes (MWNTs), carboxylated multiwalled carbon nanotubes (MWNT-COOHs), and graphene oxides (GOs), by physical adsorption without using coupling agents. The immobilized amount of laccase strongly depends on the pH of the aqueous buffers of the immobilization mixture. As the pH of the aqueous buffer for immobilization increases, the immobilized amount of laccase decreases. The activity of the immobilized laccase on the three carbon nanomaterials exhibits a bell-shaped dependence on the pH of the immobilization solution with maximum activity at pH 6 or 7. When the immobilization solution becomes acidic or basic, the activity of the immobilized laccase declines significantly. The amount and the activity of immobilized laccase were maximum for graphene oxides as substrate material for immobilization.     

Grafting maleic anhydride onto EVA and effect on the physical and rheological properties of PETG/EVA-g-MAH blends

Maleic anhydride (MAH) was grafted onto ethylene vinyl acetate copolymer (EVA) in the internal mixer in the presence of dicumyl peroxide (DCP), and a prepared reactive compatibilizer, MAH-g-EVA, was blended with Poly (ethylene glycol-co-cyclohexane-1,4-dimethanol terephthalate) (PETG). The gel content determination and element analysis (EA) was performed to confirm the grafting reaction. It was found that grafting reaction of MAH on to EVA could compete with crosslinking reaction of DCP during the modification process. In addition, the introduction of small amount of MAH showed a great effect on reducing gel content by decreasing crosslink reaction. As MAH content increased, grafted MAH concentration increased, whereas the grafting yield decreased. It was also confirmed that MAH-g-EVA acted as a reactive compatibilizer in the blend with PETG, and enhanced compatibility by reacting with the hydroxyl end groups, OH, of PETG. Addition of EVA in the blend leads a plastic deformation of PETG, and MAH had a great effect on enhancing interfacial adhesion resulting in significant increasing of % strain; however, improved compatibility could not be changed much in low strain tensile strength and Young's modulus. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Comparison of influences of NaCl and CaCl2 on the corrosion of 11% and 17% Cr ferritic stainless steels during cyclic corrosion test

During the drying stage of the cyclic corrosion test on ferritic stainless steels in the NaCl environment, the current abruptly increased and then decreased to nearly zero, indicating that pits are initiated as the salt concentration is increased, which are then repassivated when the surface is completely dry. During the wet stage, the current remained high, suggesting that pits mainly propagate during the wet stage. In contrast, in the cyclic corrosion test in the CaCl₂ environment, the current was highest during the drying stage, indicating that the electrolyte is not completely dried and corrosion mainly propagates during the drying stage.     

Effects of the addition of hemp powder on the physicochemical properties and energy bar qualities of extruded rice

Extruded rice/hemp mixtures were prepared by mixing defatted and whole hemp powders with rice flour at varying hemp levels (0%, 20%, 30% and 40%). The influence of hemp powder type and level on physicochemical and antioxidant properties was studied. The bulk densities of the extruded rice/hemp samples increased with increase in levels of added hemp powder. The extrudates blended with hemp powder had a lower water absorption index than the control (extruded rice without hemp). The extruded rice/whole hemp had more total phenolics and flavonoids and had a better scavenging effect on DPPH radicals than extruded rice/defatted hemp. The highest potential to inhibit β-carotene oxidation was found in extruded rice/40% whole hemp. Increasing amounts of hemp powder resulted in lower equilibrium moisture content of energy bars. The energy bar made with extruded rice/20% whole hemp was preferred for colour, taste and overall acceptability.     

DNA/Tannic Acid Hybrid Gel Exhibiting Biodegradability,Extensibility, Tissue Adhesiveness,and Hemostatic Ability

DNA has emerged as a novel material in many areas of materials science due to its programmability. Especially, DNA hydrogels have been studied to incorporate new functions into gels. To date, only a few methods have been developed for fabricating DNA hydrogels, such as the use of complementary sequences or covalent bond. Herein, it is demonstrated that one of the most well‐known plant‐derived polyphenols, tannic acid (TA), can form a DNA hydrogel which is named TNA hydrogel ( T A + D NA ). TA plays a role as a “molecular glue” by a new mode of action reversibly connecting between phosphodiester bonds, which is different from the crosslinking utilizing complementary sequences. TA intrinsically degrades due to ester bonds connecting between pyrogallol groups, causing a degradable DNA hydrogel. Furthermore, TNA gel is multifunctional in that the gel is extensible upon pulling and adhesive to tissues because of the rich polyphenol groups in TA (ten phenols per TA). Unexpectedly, TNA gel exhibits superior in vivo hemostatic ability that can be useful for biomedical applications. This new DNA hydrogel preparation method represents a new technique for fabricating a large amount of DNA‐based hemostatic hydrogel without chemically modifying DNA or requiring the crosslinking by complementary sequences.     

Fabrication of protective-coated SiC reinforced tungsten matrix composites with reduced reaction phases by spark plasma sintering

SiC reinforced tungsten matrix composites were fabricated via the spark plasma sintering process. In order to prevent an interfacial reaction between the SiC and tungsten during sintering, TiOx coated SiC particles were synthesized by a solution-based process. TiOx layer coated SiC particles were treated in high temperature nitriding conditions or annealed in a high temperature vacuum to form TiN or TiC coated SiC particles, respectively. The TiC layers coated on SiC particles successfully prevented tungsten from reacting with SiC; hence the proposed process resulted in successful fabrication of the SiC/W composites. The mechanical properties such as compressive strength and flexural strength of the composites were measured. Additionally, the effect of SiC on the high temperature oxidative ablation of tungsten was also investigated. The addition of SiC resulted in an improved oxidative ablation resistance of the tungsten-based composites.     

Effects of work hardening models on low-cycle fatigue evaluations of coiled tubing with CT-100 steel

In the present study, low-cycle fatigue life of a coiled tubing (CT) with a CT-100 steel was evaluated by using various work hardening models. Tensile and low-cycle fatigue tests were performed, and experimental results were used to calibrate material model constants. A nonlinear finite element model was constructed in the ABAQUS program by using a CT fatigue test machine. During the test cycles, bending and straightening conditions were repeated and histories of strains were collected. The multiaxial low-cycle fatigue life was calculated by using Manson–Coffin relation and Tresca criterion. The kinematic and combined hardening models can be used to evaluate the fatigue life of CT, and their results are conservative compared with the fatigue test results. Results of the present study can be used as the basic data in establishing CT fatigue analysis.