On a transistor-type hydrogen gas sensor prepared by an electrophoretic deposition (EPD) approach

A Pd/GaN/AlGaN heterostructure field-effect transistor (HFET)-type hydrogen gas sensor, based on an electrophoretic deposition (EPD) approach, is fabricated and studied. Due to the formation of good Schottky gate contact by an EPD approach, the studied HFET shows improved DC performance including the suppressed gate current and better thermal stabilities on current–voltage (I–V) characteristics. This is mainly attributed to the reduction of interface trap density and improved Pd morphology. The EPD-based Pd morphologies are examined by X-ray diffraction, energy dispersive spectroscopy, Auger electron spectroscopy, scanning electron microscopy, and atomic force microscopy. For the used gate-dimension of 1 μm × 100 μm, an EPD-based HFET shows low gate current of 2.9 nA, maximum drain saturation current of 490 mA/mm, and maximum extrinsic transconductance of 78.9 mS/mm at room temperature. Also, solid thermal stabilities on maximum drain saturation current (−0.46 mA/mm K) and maximum extrinsic transconductance (−0.08 mS/mm K) are found as the temperature is increased from 300 to 600 K. For hydrogen gas sensing application, at 370 K, the maximum hydrogen sensitivity of 600.1 μA/mm ppm H₂/air under a 5 ppm H₂/air ambiance and fast response time (30 s) and recovery time (47 s) under a 10,000 ppm H₂/air ambiance are obtained. The EPD approach also demonstrates advantages of low cost, simple apparatus, easy process, little restriction on the shaped substrate, composited deposition, and adjustable alloy grain size. Therefore, the proposed EPD approach gives the promise for fabricating high-performance HFET devices and hydrogen gas sensors.     

SNS collaborative learning design: enhancing critical thinking for human–computer interface design

Universal Access in the Information Society - In many cases, classrooms seem to be functioning as well as ever, though the challenges and expectations have changed quite dramatically. This study...     

Influence of channel aspect ratio on heat transfer in rotating rectangular ducts with skewed ribs at high rotation numbers

Centerline heat transfer measurements along two opposite ribbed walls in three rotating rectangular ducts roughened by 45° staggered ribs with channel aspect ratios (AR) of 1:1, 2:1 and 4:1 are performed at Reynolds (Re), rotation (Ro) and buoyancy (Bu) numbers in the ranges of 5000–30,000, 0–2, and 0.005–8.879, respectively. These channel geometries are in common use as the internal cooling passages of a gas turbine rotor blade and the tested Ro and Bu ranges are considerably extended from the previous experiences. This study focuses on the heat transfer characteristics in response to the change of AR under the parameter ranges examined. With zero-rotation (Ro = 0), the local Nusselt numbers (Nu₀) along the centerlines of two opposite ribbed walls increase as AR increases due to the increased rib-height to channel-height ratio. The Bu impact on heat transfer appears to be AR dependent, i.e. the increase of Bu elevates Nusselt number ratios Nu/Nu₀ in the square channel but impairs heat transfer in the rectangular channels of AR = 2 and 4. Acting by the Coriolis effect alone, all the leading edge Nu values in the present Ro range are lower than the zero-rotation references but started to recover as Ro increases from 0.1 in the channels of AR = 1, 2 and from 0.3 in the channel of AR = 4. The trailing edge Nu/Nu₀ ratios increase consistently from unity as Ro increases but their responses toward the increase of AR are less systematic than those found along the leading edge. The above findings, with the aids of extended Ro and Bu ranges achieved by this study, serve as the original contributions for this technical community. The Nu/Nu₀ ratios in the rotating channels of AR = 1, 2, and 4 fall in the ranges of 0.6–2.2, 0.5–2.7, and 0.5–2.1, respectively. A set of heat transfer correlations is derived to represent all the heat transfer data in the periodically developed flow regions of three rotating ducts.     

Fast agglomerative clustering using information of k-nearest neighbors

In this paper, we develop a method to lower the computational complexity of pairwise nearest neighbor (PNN) algorithm. Our approach determines a set of candidate clusters being updated after each cluster merge. If the updating process is required for some of these clusters, k-nearest neighbors are found for them. The number of distance calculations for our method is O(N²), where N is the number of data points. To further reduce the computational complexity of the proposed algorithm, some available fast search approaches are used. Compared to available approaches, our proposed algorithm can reduce the computing time and number of distance calculations significantly. Compared to FPNN, our method can reduce the computing time by a factor of about 26.8 for the data set from a real image. Compared with PMLFPNN, our approach can reduce the computing time by a factor of about 3.8 for the same data set.     

Study of Al–Ti/Si bi-layer as the recording media for write-once HD-DVD optical disks

Optimum structure for HD-DVD optical disks containing Al–Ti/Si bi-layer recording system was identified by reflectivity simulation and dynamic test of disk samples. For the disk sample with optimized structure, the maximum partial response signal-to-noise ratio (PRSNR) of 19.1 dB, minimum simulated bit error rate (sbER) of 1.7 × 10^?7 and modulation >0.6 were achieved at the writing power (P_w) = 11.2 mW. Transmission electron microscopy (TEM) revealed that the polycrystalline granular clusters constitute the recording marks. Subsequent analyses evidenced that element mixing/alloy reactions occur in between Si and Al–Ti layers and the formation of Al_3.21Si_0.47 crystalline phase is responsible for the signal recording in the disk samples.     

Corrosion fatigue behavior of dissimilar metal weldments under nominal constant ΔK loading mode in a simulated BWR coolant environment

Corrosion fatigue behavior of the dissimilar metal weldment, Alloy 52-A508, under a simulated BWR coolant condition was studied. Corrosion fatigue crack growth rates of the dissimilar metal weldments were observed to increase with crack extension under the nominal constant ΔK loading mode. It could be accounted for by a decrease in the Cr and Ni contents and the crack closure effect with the weld depth. Finite element analysis on the welding residual stress was performed. The trend of analytical results agreed well with that of the residual stress measurements obtained by a hole-drilling strain gauge method.     

Design of micro-retainer to counter-balance spinning seismic proof mass

An innovative magnetic module which is concurrently capable of performing as an actuator and a sensor is proposed and analyzed. The magnetic module is basically similar to a micro-scale Linear Variable Differential Transformer (LVDT) which is employed to actively adjust the height of a rotating seismic disc used in a gyroscope so that the pitch rate induced by Coriolis effect, due to exerted angular excitation, can be accurately measured. That is, the micro-magnetic module acts like an actuator for height regulation on the seismic proof mass by applying appropriate electric current to the primary winding of the LVDT unit. On the other hand, the secondary winding pair of the LVDT acts like a sensor which can detect the gap change, between the seismic rotating disc and the micro-magnetic LVDT module, and the rotation speed (i.e., frequency) by the induced current.     

钢坯连续加热炉计算机在线控制数学模型

在离线模型的基础上.开发了加热炉在线计算机控制数学模型;这种模型系统不仅能够最大程度地节能,而且保证了出钢温度的准确控制,结果表明:出炉钢坯温度与目标出炉温度偏差小于15℃.     

An expanded SEMATECH CIM framework for heterogeneous applications integration

A significant effort in recent computer-integrated manufacturing (CIM) development was carried out by SEMATECH who had laid out and created an open framework for the integration of manufacturing execution system applications running in semiconductor industries at the factory operation level. This paper presents the feasibility to incorporate basic manufacturing applications at the factory engineering level, which include product design, process planning, and material requirement planning, into the SEMATECH CIM framework to form a generic framework across both factory operation level and factory engineering level. The CIM framework established in this paper was aimed to provide a reusable integrated system framework that clearly specifies the functional interface boundaries and standard information model of the required components, in general, manufacturing systems at both factory operation and factory engineering levels. Standard unified modeling language (UML) diagrams and Petri nets have been utilized to model and analyze the specifications and dynamic behaviors of this generic CIM framework. The goal is to build a framework by creating a common, modular, flexible, and integrated object model that unifies an advanced object-oriented architecture concept and heterogeneous manufacturing application development in an open and multisupplier CIM system environment.