Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

Polyetherimide substrates for future high density optical data storage

Polyetherimide (PEI) substrate for next‐generation high density optical data storage is fabricated and characterized. Cover‐layer incident or first‐surface recording configurations do not require optical properties of the substrate, which are the prerequisite conditions for the conventional material of polycarbonate (PC). Instead of the optical properties, good mechanical properties with a sufficient transcribability are required. Even though PEI has higher glass transition temperature than that of PC, a microscopic transcribability of PEI is comparable with PC by laminating a thermal insulation layer on the backside of a stamper to retard the heat flow. A macroscopic warpage of PEI substrate is smaller than that of PC substrates, which reduces tilt and servo burden. The lowest critical speed coupled with the flutter of PEI substrate is larger than that of PC substrate because of the mechanical properties of PEI. POLYM. ENG. SCI., 48:97–101, 2008. © 2007 Society of Plastics Engineers     

基于USB的155 Mb/s码型发生器的研制

介绍了一种带USB接口的光的155Mb／s码型发生器。伪随机码和其他格式的码型由PC产生通过USB接口进入双口RAM，再经串并变换后由光发射模块发射。该系统可方便地设定各种格式的码型，并同时具备光接口和电接口，可广泛应用于光通信各种实验中，具有重要的实用价值。     

基于OpenGL和MFC的石油井管道的绘制

介绍了O penGL的知识和石油井的基本概念,利用O penGL实现石油井管道的绘制,包括石油井数据的变换和管道起始点的跟踪和角度的旋转。纹理光照效果增强图形生动性,交互操作改变图形视角。并且利用DAO数据库和L istv iew控件实现数据保存和修改。该程序能够完成石油井的管道绘制和数据保存。     

Formation mechanism of 21R AlN-polytypoids in aluminothermic reduction and nitridation process

Synthesis of 21R AlN polytypoids was investigated using Al and ultrafine SiO₂ powder in a flowing nitrogen atmosphere by means of thermal gravity (TG), differential scanning calorimeter (DSC), X-ray diffractometer (XRD) and scanning electronic microscope (SEM) linked with energy dispersive spectrometer (EDS). The results showed that the formation mechanism of AlN polytypoids was different from that in reaction sintering process using Si₃N₄, AlN, Al₂O₃ and other sintering additive as raw materials. It was suggested that firstly Al reduce SiO₂ into Si and is also nitrided into AlN, then AlN, Al₂O₃ and SiO₂ dissolve into silicon liquid until the AlN polytypoids precipitate in saturated liquid in a flowing nitrogen atmosphere at lower than 1700 °C.     

Synthesis of Mg-α-sialon from the mixture of silicon, aluminum and magnesia powders in a flowing nitrogen atmosphere

Synthesis of Mg-α-Sialon has been investigated by the mixture of silicon, aluminum and magnesia powders in a flowing nitrogen atmosphere in the range of 1300–1600 °C, when Mg-α-Sialon is designed with a chemical formulation of Mg _x Si_12−3x Al_3x O _x N_16−x in present work. The results showed that Mg-α-sialon initially occurred at 1400 °C and basically increased with elevated temperatures. For the samples of x = 0.6, 0.8 and 1.0 the products mainly consisted of Mg-α-Sialon with small amounts of Si, AlN and 21R AlN-polytypoid phases at 1600° C. However, in final products of x = 1.2, 1.4 and 1.6 only a little of Mg-α-Sialon formed and a great amount of Si remained in these samples at all the fired temperatures. Fortunately, the content of Mg-α-Sialon in these samples were obviously increased by adding a small amount of α-Si₃N₄ as seeds before nitridation.     

A Study on NMR and GC/MS Spectra of the Isomers of Linear Hexyl Naphthalene

The GC/MS and NMR analysis of the reaction products of naphthalene with 1-bromohexane were reported. The products obtained were suggested to have six isomers of linear hexylnaphthalene and the structure of each isomer was determined by GC/MS and NMR spectra. For the first time, the unique chemical shift data were obtained. The content of each isomer calculated by ¹H NMR and ¹³C NMR spectra was consistent with that by GC/MS spectra, which confirmed the accuracy of NMR data.     

Tri-Gate Bulk MOSFET Design for CMOS Scaling to the End of the Roadmap

A tri-gate bulk MOSFET design utilizing a low-aspect-ratio channel is proposed to provide an evolutionary pathway for CMOS scaling to the end of the roadmap. 3-D device simulations indicate that this design offers the advantages of a multi-gate FET (reduced variability in performance and improved scalability) together with the advantages of a conventional planar MOSFET (low substrate cost and capability for dynamic threshold-voltage control).     

Automating application software generation

Many approaches have been proposed to enhance software productivity and reliability. These approaches typically fall into three categories: the engineering approach, the formal approach and the knowledge-based approach. But the optimal gain in software productivity cannot be obtained if one relies on only one of these approaches. This paper describes the work in knowledge-based software engineering conducted by the authors for the past 10 years. The final goal of the research is to develop a paradigm for software engineering which integrates the three approaches mentioned above. A knowledge-based tool which can support the whole process of software development is provided in this paper.