Micromechanical modeling of grain boundary resistance to cleavage crack propagation in ferritic steels

In ferritic steels a propagating cleavage microcrack changes its propagation direction as it advances from grain to grain. This is due to differences in the orientation of the cleavage planes of two neighboring grains. In order to reach a cleavage plane in a new grain, a microcrack must first penetrate the grain boundary. Grain boundaries therefore act as natural barriers in cleavage fracture. The influence of a grain boundary and the associated misorientation in cleavage planes on crack arrest is here examined using a 3D finite element model with axisymmetric periodicity, representing two grains whose cleavage planes are tilted and twisted relative to each other. The temperature dependent mechanical properties of ferrite are modeled using a temperature dependent viscoplastic response. The development of the crack front as the microcrack penetrates through a grain boundary is here presented. The influence of the twist misorientation on the critical grain size, defined as the largest grain size that can arrest a rapidly propagating microcrack, is examined in a temperature range corresponding to the ductile to brittle transition (DBT) region. It is shown that when both tilt and twist misorientation are present, the influence of tilt and twist, respectively, on crack growth resistance can be decoupled.     

Wideband Low‐Reflection Transmission Lines for Bare Chip on Multilayer PCB

The pad pitch of modern radio frequency integrated circuits is in the order of few tens of micrometers. Connecting a large number of high‐speed I/Os to the outside world with good signal fidelity at low cost is an extremely challenging task. To cope with this requirement, we need reflection‐free transmission lines from an on‐chip pad to on‐board SMA connectors. Such a transmission line is very hard to design due to the difference in on‐chip and on‐board feature size and the requirement for extremely large bandwidth. In this paper, we propose the use of narrow tracks close to chip and wide tracks away from the chip. This narrow‐to‐wide transition in width results in impedance discontinuity. A step change in substrate thickness is utilized to cancel the effect of the width discontinuity, thus achieving a reflection‐free microstrip. To verify the concept, several microstrips were designed on multilayer FR4 PCB without any additional manufacturing steps. The TDR measurements reveal that the impedance variation is less than 3 Ω for a 50 Ω microstrip and S11 better than –9 dB for the frequency range 1 GHz to 6 GHz when the width changes from 165 µm to 940 µm, and substrate thickness changes from 100 µm to 500 µm.     

Synthesis and polymerization of alkyl halide-functional cyclic carbonates

To increase the diversity in functional aliphatic polycarbonates, a series of novel chloro- and bromo-functional six-membered cyclic carbonate monomers were synthesized. Despite asymmetry in the monomer functionalities, homopolymerization of the monomers afforded semicrystalline polycarbonates with a high tendency to crystallize from the melt and/or on precipitation from a THF solution. Melting points were found in the 90-105 °C or 120-155 °C range for polymers comprising methyl or ethyl moieties, respectively, in the backbone. The monomers were further copolymerized with trimethylene carbonate to form random copolymers. Even among some of these random copolymers elements of semicrystallinity were found as confirmed by melting endotherms in DSC. The results clearly show that the incorporation of alkyl halide functionalities in aliphatic polycarbonates may lead to materials with a high ability to form crystallites, even in random copolymers, likely driven by polar interactions due to the presence of the halide functionalities.     

Effect of nanofillers on the flame retardant properties of a polyethylene–calcium carbonate–silicone elastomer system

This study shows the effects of three different nanofillers on the viscosity properties and fire behavior of a halogen‐free flame retardant system. The original system, based on ethylene‐acrylate copolymer, calcium carbonate, and a silicone elastomer, shows good flame retardant properties. One of the nanofillers, montmorillonite (MMT), significantly increases the viscosity above 250^°C, resulting in reduced dripping and decreased heat release rate. The ash residue, however, is very brittle, indicating poor interactions between the MMT and other components of the system. The second nanofiller, sepiolite, shows no improvement on the flame retardant properties of the system. Reduced dripping is observed when a small amount of the third nanofiller, polyhedral oligomeric silsesquioxane, POSS, is incorporated into the system. In this case, high silica content on the surface indicates char formation originating from the POSS. However, an increased heat release is observed when POSS is used in the system. Copyright © 2010 John Wiley & Sons, Ltd.     

Reversibly erasable nanoporous anti-reflection coatings from polyelectrolyte multilayers

For nearly two centuries, researchers have sought novel methods to increase light transmission in optical systems, as well as to eliminate unwanted reflections and glare. Anti-reflection coatings and surfaces have enabled the increasing performance demands of optical components fabricated from glass-based optical materials. With the current trend of technology moving towards optically transparent polymeric media and coatings, the need for anti-reflection technology and environmentally benign processing methods for polymeric materials independent of shape or size has become quite apparent. We describe an economical, aqueous-based process controlled at the molecular level that simultaneously coats all surfaces of almost any material. Systematically designed nanoporous polymer films are used, which are suitable for optical applications operating at both visible and near-infrared wavelengths. These high-efficiency anti-reflection coatings are created from phase-separated polyelectrolyte multilayer films that undergo a reversible pH-induced swelling transition. Furthermore, such films, easily patterned by an inkjet printing technique, possess potential for pH-responsive biomaterial and membrane applications.     

Prediction of chromatographic retention and protein identification in liquid chromatography/mass spectrometry

Liquid chromatography coupled on- or off-line with mass spectrometry is rapidly advancing as a tool in proteomics capable of dealing with the inherent complexity in biology and complementing conventional approaches based on two-dimensional gel electrophoresis. Proteins can be identified by proteolytic digestion and peptide mass fingerprinting or by searching databases using short-sequence tags generated by tandem mass spectrometry. This paper shows that information on the chromatographic behavior of peptides can assist protein identification by peptide mass fingerprinting in liquid chromatography/mass spectrometry. This additional information is significant and already available at no extra experimental cost.     

Uzawa Conjugate Gradient Domain Decomposition Methods for Coupled Stokes Flows

This paper deals with nonoverlapping domain decomposition methods for two coupled Stokes flows, based on the duality theory. By introducing a fictitious variable in the transmission condition and using saddle-point equations, the problem is restated as a linearly constrained maximization problem. According to whether constraints are uncoupled Stokes problems or uncoupled Poisson problems, two Uzawa-type domain decomposition algorithms are proposed. The results of some numerical experiments on a model problem are given.