Microstructural investigation of long-term degradation mechanisms in GFRP dowel bars for jointed concrete pavement

Steel dowel bar is used to transfer loads in concrete pavement slab. However, once the steel dowel bar corrodes, it may cause faults, such as joint freezing in concrete pavement, level differences resulting from spalling or decreased efficiency of load transfer, etc., which are the same problems experienced by typical reinforcing steel. This study evaluated the applicability of glass fiber-reinforced polymer (GFRP) dowel bar as a substitute for steel dowel bar. A microstructural analysis was conducted to examine the decrease in durability of GFRP dowel bar exposed to deterioration environments. To analyze the deterioration mechanism of GFRP dowel bar, scanning electron microscopy was employed and the porosity was measured by the gas absorption method. It was concluded that the longer the GFRP dowel bar was exposed to deterioration environments, the more the interlaminar shear stress decreased. This result was validated by the microstructural analysis. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of monodisperse poly(vinyl alcohol) microspheres by heterogeneous surface saponification and iodine complex formation

Monodisperse poly(vinyl acetate) (PVAc) microspheres with high molecular weight obtained by suspension polymerization of vinyl acetate were saponified in alkaline aqueous solution to keep their spherical structure. The saponification was restricted on the surface of the PVAc microspheres and obtained particles had skin/core structure. Various poly(vinyl alcohol) (PVA) microspheres with different diameters and degrees of saponification (DSs) were obtained. The conversion of PVAc to PVA during the heterogeneous surface saponification time were examined by nuclear magnetic resonance spectroscopy and after 72 h hydrogel type PVA microspheres completely saponified were obtained. The crystal melting temperatures of the microspheres obtained by the saponification were measured a constant value of 238°C irrespective of varying DS, and the peaks became enlarged as reaction time. Iodine complexes were formed in saponified microspheres with DS of 41% and 99% by immersing them in I₂/KI aqueous solution and decomposed by the reduction of I₂ in the complexes to 2I^? using sodium sulfite to confirm whether the skin formed through the saponification was composed of PVA with high VA content. Obviously, characteristic blue color developments owing to I₅^?‐PVA complexes were observed in both saponified regions and a red in the PVAc core. Consequently, it was concluded that the PVA skins formed by heterogeneous surface saponification had high DSs. Such complexes endowed polymeric microspheres a good radiopacity which would be useful in clinical treatment of vascular diseases and were examined by X‐ray irradiation image. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The application of microencapsulated phase‐change materials to nylon fabric using direct dual coating method

The fabrication of functional textiles able to provide thermal regulation and comfort for the body has attracted increasing interest in recent years. This research investigated fabric coatings containing energy absorbing, temperature stabilizing, phase‐change material microcapsules (PCMMcs), and their methods of application. Specifically, a coated fabric was directly prepared by a dual‐type coating method, in which the PCMMcs were dispersed in a polyurethane coating solution with no binder. The thermal performances of the dual‐coated samples were evaluated by differential scanning calorimetry, and their physical characteristics were examined by scanning electron microscopy, thermal vision camera, porosity, water vapor transmission rate (WVTR), and water entry pressure (WEP) analyses. Furthermore, the microclimate characteristics of the thermally enhanced fabrics were investigated under experimental conditions using a human‐clothing‐environment (HCE) simulator system. The study results confirmed the superior performance of the dual‐coated fabrics in terms of thermal regulation and body comfort, compared with those coated by the dry or wet coating method, because of the improved WEP, WVTR, and thermal performance. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Differentially coherent code acquisition in the MIMO-aided multi-carrier DS-CDMA downlink

Both differentially coherent and non-coherent code acquisition schemes designed for the multiple-input multiple-output (MIMO)-aided multi-carrier (MC)-DS-CDMA downlink are analysed, when communicating over uncorrelated Rayleigh channels. The attainable mean acquisition time (MAT) performance is studied as a function of both the number of multiple transmit/multiple receive antennas and that of the number of subcarriers. It is demonstrated that in contrast to the expectations, when the number of multiple transmit antennas and/or that of the subcarriers is increased in both the differentially coherent and the non-coherent code acquisition scenarios, the achievable MAT deteriorates over the entire signal-to-interference plus noise ratio (SINR) per chip (E_c/I_o) range considered, except for the scenario of single-carrier (SC)-DS-CDMA using P = 2 transmit antennas and R = 1 receive antenna. As expected, the degree of performance degradation depends upon the specific scheme and the E_c/I_o ratio considered, although paradoxically, the correctly synchronised MIMO-aided system is capable of attaining its target bit error ratio performance at reduced SINR values.     

New approach to enhance adhesions between carbon nanotube emitters and substrate by the combination of electrophoresis and successive electroplating

Complementary electroplating combined with electrophoresis enhanced the field emission characteristics of emitters by improving the adhesions between CNT emitters and substrate. The emitting current of the CNT emitters prepared by our combined method increased nine times higher than that of CNT emitters prepared by electrophoresis only, since electroplating improved the adhesion of CNT emitters. During the life-time measurement for 10 h, the emitting current of CNT emitters fabricated by electrophoresis only was drastically decreased to 13% of the initial current, while that prepared by the combination of electrophoresis and successive electroplating decreased to 64% of the initial current. We suggest that our method is a promising approach for the efficient fabrication of reliable CNT emitters.     

Quantification of the layer dispersion degree in polymer layered silicate nanocomposites by transmission electron microscopy

As the performance of polymer layered silicate nanocomposites strongly depends on their interior layer dispersion, quantification of the layer dispersion degree is needed. In this work, a new methodology was developed to determine the dispersion parameter D_0.1, based on the measurement of the free-path spacing distance between the single clay sheets from the transmission electron microscopy (TEM) images. Several examples of exfoliated, intercalated, and immiscible composites were studied. It was found that the exfoliated composites had D_0.1 over 8%, while that of intercalated composites were between 4 and 8%. In the case of intercalation, a high frequency peak appeared at a short spacing distance in the histogram, which was a characteristic of the intercalation, distinct from the exfoliation. The main utility of this TEM methodology is for the quantification of exfoliated or intercalated samples with small number of layers with stacks. The dispersion parameter D_0.1 below 4% was suggested to classify as immiscible. A unique advantage of the TEM measurement is that the dispersion degree of different fillers can be counted individually.     

Testing of the multi-application small light water reactor (MASLWR) passive safety systems

Experimental thermal hydraulic research has been conducted at Oregon State University for the purpose of assessing the performance of a new reactor design concept, the multi-application small light water reactor (MASLWR). The MASLWR is a pressurized light water reactor design with a net output of 35 MWe that uses natural circulation in both normal and transient operation. Due to its small size, portability and modularity, the MASLWR design is well suited to help fill the potential need for grid appropriate reactor designs for smaller electricity grids as may be found in developing or remote regions. The purpose of the OSU MASLWR test facility is to assess the operation of the MASLWR under normal full operating pressure and full temperature conditions and to assess the passive safety systems under transient conditions. The data generated by the testing program will be used to assess computer code calculations and to provide a better understanding of the thermal-hydraulic phenomena in the design of the MASLWR NSSS. During this testing program, four tests were conducted at the OSU MASLWR test facility. These tests included one design basis accident and one beyond design basis accident. During the performance of these tests, plant operations to include start up, normal operation and shut down evolutions were demonstrated successfully.