Strength and ductility under dynamic loading in fine- grained IN905XL aluminum alloy

Three IN905XL aluminum alloys with fine grain (1 μm), intermediate grain (3 μm), and coarse grain (5 μm) have been developed by a combination of mechanical alloying (MA) and conventional extrusion in order to investigate their mechanical properties at dynamic strain rates of 1 × 10³ and 2 × 10³ s⁻¹ and a quasi-static strain rate of 10^-3 s⁻¹. Flow stresses are found to increase with decreasing grain size for all the strain rates tested. Negative strain-rate sensitivity of flow stress is observed up to 1 × 10³ s⁻¹ in both intermediate- and coarse-grained IN905XL. At the highest strain rate of 2 × 10³ s⁻¹ however, all samples showed a positive strain-rate sensitivity of strength. Total elongation at high strain rates is generally larger than that at low strain rates. Total elongation also decreases with grain size for all the strain rates. This decrease in elongation results from an initiation of microcracks at interfaces between the matrix and particles finely dispersed near grain boundary regions, introduced during MA processing; then, this initiation leads elongation of alloys to small limited values. Formerly with the Department of Mechanical Systems Engineering, University of Osaka Prefecture. This article is based on a presentation made in the symposium “Dynamic Behavior of Materials,” presented at the 1994 Fall Meeting of TMS/ASM in Rosemont, Illinois, October 3-5, 1994, under the auspices of the TMS-SMD Mechanical Metallurgy Committee and the ASM-MSD Flow and Fracture Committee.     

An entropy model for shear deformation of granular materials

A statistical mechanical analogy for characterization of granular materials is discussed by using such notions as the state of the material, the density of states, entropy, canonical distribution and the partition function. The transition law of states during shear deformations of the material is microscopically investigated in the case of two-dimensional model granular materials. The assumption of entropy growth is shown to characterize the dilatancy of the material. A rough proof is given by assuming the measure preserving property of the transition and showing its ergodicity.     

Cooperative behavior of various agents in dynamic environment

The multi-agent model is a model in which agents with limited ability cooperate each other to accomplish a goal. In this paper, we introduce a multi-agent model in which agents are created to imitate real ants. There are two different type of agents, each type of which has a particular task. We designed agents to communicate each other by using pheromone considering noise. On this model, we observed cooperative behavior of agents and evaluated conditions to make an order of behavior in the model.     

Elevated levels of tumor necrosis factor-alpha (TNF-alpha) and interleukin-6 (IL-6) activities in the sera and milk of cows with naturally occurring coliform mastitis

The presence of tumor necrosis factor-alpha (TNF-alpha) and interleukin-6 (IL-6) activities was determined in milk and serum of cows with naturally occurring coliform mastitis (CFM). TNF-alpha was detected in the sera from 26 of 32 cows with CFM. TNF-alpha levels were higher in the sera than in the milk. IL-6 was high in the sera of surviving CFM animals, but was low in animals that died and in healthy controls. Furthermore, the mean level of IL-6 was 20-fold higher in the milk than in the sera of mastitic cows. The level of IL-6 in the serum was correlated to that in the milk in individual animals. The presence of IL-6 and TNF-alpha in the sera appears to relate to severe clinical condition of CFM, in the milk whereas they may play a role in generating inflammation of the mammary gland.     

Electrotunable Non‐reciprocal Laser Emission from a Liquid‐Crystal Photonic Device

A liquid crystal (LC) photonic device with an anisotropic optical heterojunction structure has been fabricated. The device has a phase‐retarding nematic LC (NLC) layer sandwiched between two polymer cholesteric LC films with right‐handed helices of different pitches. Electrotunable non‐reciprocal light transmittance and unidirectional circularly polarized (CP) lasing emission have been successfully demonstrated for this device structure. Two left CP (LCP) lasing emission peaks are observed at the edges of the overlapping region between the two photonic bands in the structure and are shifted upon the application of a voltage. In contrast, a non‐reciprocal right CP (RCP) lasing emission peak emerges at one of the band edges and diminishes upon the application of a voltage. These phenomena are interpreted based on the selective reflection of RCP light and the reorientation of the NLC molecules by the application of a voltage.     

Implicit integration and consistent tangent modulus of a time‐dependent non‐unified constitutive model

This paper describes the implicit integration and consistent tangent modulus of an inelastic constitutive model with transient and steady strain rates, both of which are time‐ and temperature‐dependent; the transient rate is influenced by the evolution of back stress decomposed into parts, while the steady rate depends only on applied stress and temperature. Such a non‐unified model is useful for high‐temperature structural analysis and is practical owing to the ease in determining material constants. The implicit integration is shown to result in two scalar‐valued coupled equations, and the consistent tangent modulus is derived in a quite versatile form by introducing a set of fourth‐rank constitutive parameters into the discretized evolution rule of back stress. The constitutive model is, then, implemented in a finite element program and applied to a lead‐free solder joint analysis. It is demonstrated that the implicit integration is very accurate if the multilinear kinematic hardening model of Ohno and Wang is employed, and that the consistent tangent modulus certainly affords quadratic convergence to the Newton–Raphson iteration in solving nodal force equilibrium equations. Copyright © 2003 John Wiley & Sons, Ltd.     

TRVs and fault clearing stresses in extra-high-voltage radial networks

To cope with the high rate of increase of power demand in the main industrialized districts in Japan, 550-kV transmission systems covering the districts have been reinforced, with most of the main power plants connected directly to these systems. Through 550-/300-kV substations, the majority of power to the districts is supplied by 300-kV systems. To limit the excess short-circuit capacity in the 300-kV systems, they tend to be reconstructed as so-called radial networks. In radial networks with high short-circuit capacity and relatively small number of transmission lines connected to the substation busbars, the rate of rise of TRV can be far higher than standard value. This paper analyzes the transient recovery voltages (TRV) in such extra-high-voltage radial networks in Japan, together with the relevant stresses to circuit-breakers during fault clearings. Future system conditions have also been introduced. As the typical rate of rise of the TRV values, more than twice that of today's standard ones are probable.     

Design of electrofusion joints and evaluation of fusion strength using fusion simulation technology

Fusion simulation is one of the key techniques in designing and producing electrofusion (EF) joints for gas distribution and in evaluating fusion joint integrity. This paper describes the result of a numerical simulation of a thermal fusion process, using the finite element method. A nonlinear heat transfer computer program was used to obtain the temperature profile of a large electrofusion joint at fusion. The effects of applied voltage, heating time, wire pitch, and ambient temperature were examined for designing a 150-mm EF joint. A method to shorten the cooling time was also investigated. The fusion condition range suitable for a 150-mm EF joint was found to be slightly narrower than that suitable for a 50-mm EF joint. Examination of the effect of wire pitch revealed that if the pitch is extremely large, thermal degradation starts in the resin close to the wire before the fusion-interface strength reaches the maximum value. We have developed a program to simulate the process of closing the gap between the pipe and the joint due to resin expansion and melting after the power is supplied.     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

The 100 G capturing robot - too fast to see

This paper discusses the capturing robot with the maximum acceleration of 100 G in design specification. We aim find the combination of the arm with a mass of 0.1 kg and the spring capable of producing the initial compressed force of 100 N, in order to achieve the 100 G. To reduce the total capturing time, we propose an arm/gripper coupling mechanism where the spring energy initially accumulated in the arm is transferred to the kinetic energy of the arm and continuously to the kinetic energy for closing the gripper at the capturing point without any time lag. The experimental results show the maximum acceleration of 91 G and the capturing time of 25 ms were achieved. Experiments on capturing a dropping ball were also executed with the assistance of the 1 ms-vision.