Switching Phenomena between Laminar and Turbulent Flows of Superfluid 4He Generated by a Vibrating Wire

We have investigated the turbulence transition of the superfluid ⁴He flow generated by a vibrating wire. For a 1.2-kHz vibrating wire, we observed intermittent switchings between laminar and turbulent flows. The switching rate decreases with increasing temperature above 100 mK, until no occurrence of the switchings at 350 mK. For a 2.4-kHz vibrating wire, we find that the switching rate is much lower than that of the 1.2-kHz vibrating wire even at low temperatures. This result indicates that a mechanism causing the switchings is influenced by the temperature and the oscillation frequency of the superfluid flow.     

Capillary rise properties of porous mullite ceramics prepared by an extrusion method with various diameters of fiber pore formers

Porous mullite ceramics with unidirectionally oriented pores were prepared by an extrusion method using rayon fibers as the pore formers. Rayon fibers of 8.1, 9.6, 16.8, and 37.6 μm in diameter were used as the pore formers and were kneaded with alumina powder, kaolin clay, China earthen clay, and water to form pastes. These pastes were extruded into cylindrical tubes, dried, and fired at 1500 °C for 4 h. The apparent porosities ranged from 45.7 to 48.2 %. The pore size distributions showed a sharp peak at 9.4, 10.0, 15.6, and 30 μm with increasing fiber diameters. The height of the capillary rise was 1780, 1670, 1320, and 950 mm with increasing fiber diameter. The maximum capillary rise is much higher than previously reported. The contact angle and effective pore radius that determine the capillary rise ability were calculated by fitting the capillary rise curves using the Fries and Dreyer’s equation.     

Simulated crepitus and its reality-based specification using wearable patient dummy

Physical therapists are trained in manual examination techniques to test the impaired motor functions of patients. In this study, we have introduced a wearable robotic dummy joint to simulate disordered joint resistances or behaviors to support physical therapists in learning such techniques. We developed a discontinuous joint friction model based on a stick-slip phenomenon to simulate knee joint resistances caused by crepitus, a typical symptom accompanied by osteoarthritis. Practicing therapists participated in a reality-based evaluation test and specified acceptable parameter sets to adjust the simulated crepitus for the exoskeletal patient robot. The simulated crepitus and wearable dummy joint are expected to support the training of physical therapists.     

Structure Analysis of Molten Ba–Ge Alloys Using Electrostatic Levitation Technique Combined With High-Energy X-Ray Diffraction

High-energy synchrotron X-ray diffraction experiments were performed for clathrate-forming barium–germanium (Ba–Ge) alloys in the liquid state near the eutectic composition. The accurate structure information of highly reactive melts has been obtained by applying electrostatic levitation technique as a containerless method. The structure information obtained from the reverse Monte Carlo simulation suggests that the short-range ordering between the Ge atoms occurs with the addition of Ba atoms in the liquid Ba–Ge alloys. This can be associated with the formation of the cage-like structure composed of the Ge atoms in the liquid alloys near the eutectic composition.     

TEM,XPS and SIMS Analyzes on Grain Boundary of Lanthanum Chromites

The morphological characteristics, chromium valence state, and cation transport in the vicinity of grain boundary in La_1-xCa_xCrO₃ were investigated by using TEM/EDS, XPS and SIMS techniques. The width of grain boundary was around 1 nm where anomalous enrichment of calcium was observed. Higher valence state of chromium such as Cr⁶⁺(d⁰) was detected in the grain boundaries whereas Cr³⁺(d³) and Cr⁴⁺(d²) were dominant in the bulk. Very fast interdiffusion of alkaline earths was observed in the Sr²⁺-La_0.75Ca_0.25CrO₃ system. All observed phenomena were correlated by assuming the A-site vacancy which may be induced by the formation of Cr⁶⁺ at grain boundaries.     

Semi-globalization of stochastic spectral synthesis

This paper describes a new approach to stochastic modeling for natural objects that provides a unified model for describing terrains, clouds, sea waves and many other shapes. The geometrical data of the model can be created or modified without undue computational time, simply by specifying several parameters. In addition, these parameters have intuitive meanings, which make it easy to control the model's geometry. Then the models for different natural objects can be effectively combined through some functional operations, which makes the method more flexible for acquiring realistic images of complex three-dimensional scenes.     

Effects of winding connections on characteristics of a five‐phase stepping motor

A method for calculating the single‐step response of five‐phase hybrid stepping motors is obtained. The effects of winding connecting methods—(1) star‐bipolar SB, (2) pentagon PD, and (3) new pentagon NP—on the single‐step response are investigated. By application of the above calculation method, the continuous rotating characteristics are studied. It is found that the maximum slewing pulse rate of NP is higher than that of SB and PD connections, and that the variation of the rotor speed at high speed with the SB and PD connections is larger than that with the NP connection. The effects of the current waveform on the oscillation characteristics and relations between the current waveform and the winding connections are investigated. © 2001 Scripta Technica, Electr Eng Jpn, 136(1): 47–56, 2001     

Study on environmental effect on fatigue and creep-fatigue strength of 316FR stainless steel in sodium at elevated temperature

Low-carbon 316 stainless steel with medium-nitrogen (316FR) is considered as the principal structural material for next generation fast breeder reactor (FBR) plants in Japan. The material strength standard and the creep-fatigue life evaluation method for 316FR have been developed. However, they are based on the results of material tests in air, while actual structural material will be used mainly in liquid sodium environment in the plants. In order to clarify the environmental effect, cyclic bending tests were carried out with and without hold time in sodium. Tested materials were 316FR and conventional 304 and 316 stainless steels. Weld metal of 316FR was also tested. As a result, it was found that fatigue and creep-fatigue lives of 316FR in sodium were larger than those in air and no explicit consideration of the environmental effect is necessary in design. It was also found that the life evaluation method based on the ductility exhaustion concept is applicable to creep-fatigue life assessment in sodium.