Measurement of nonlinear mechanical properties of PDMS elastomer

This paper presents the measurement of the nonlinear mechanical properties of polydimethylsiloxane (PDMS) elastomer based on the mixing ratio of base polymer to curing agent. Strip-type PDMS samples with different mixing ratios were prepared using a simple coating, curing, and cutting process. A cyclic uniaxial tension test with a fixed magnitude of applied strain and a single-pull-to-failure tension test were performed with a micro-tensile tester at room temperature.Our new finding is that when the PDMS is mixed with excessive curing agent, stress softening occurs and residual strain exists in cyclic tension tests when the magnitude of the applied strain increases. For the PDMS-05 samples, in which the mixing ratio of base polymer to curing agent was 5 to 1, there were large differences in the stresses for the same strain level under loading and unloading during the first cycle with a 100% fixed strain amplitude, but the softening effect of the stress in the PDMS dropped rapidly starting from the second cycle.Nonlinear mechanical Neo-Hookean, third-order Mooney, and second-order Ogden models of three different PDMS films were computed from the stress-strain data. The results showed that all models were preferable for the small strain region of PDMS compared with other models. In the nonlinear, large strain region, only the second-order Ogden model properly described the mechanical behavior of the PDMS, while the Neo-Hookean and third-order Mooney-Rivlin models were too stiff or flexible in the measurement range. The bulk modulus of PDMS increased with the amount of curing agent in it. Therefore, the second-order Ogden model is preferable for analyzing the PDMS structure over the entire measurement range. This could provide reasonable mechanical models of PDMS for rapid computational prototyping and for designing active and passive components from PDMS.     

Mixing characteristics of pulsed air-assist liquid jet into an internal subsonic cross-flow

Penetration depth,spray dispersion angle,droplet sizes in breakup processes and atomization processes are very important parameters in combustor of air-breathing engine.These processes will enhance air/fuel mixing inside the combustor.Experimental results from the pulsed air-assist liquid jet injected into a cross-flow are investigated.And experiments were conducted to a range of cross-flow velocities from 42～136 m/s.Air is injected with 0～300kPa,with air-assist pulsation frequency of 0～20Hz.Pulsation frequency was modulated by solenoid valve.Phase Doppler Particle Analyzer(PDPA) was utilized to quantitatively measuring droplet characteristics.High-speed CCD camera was used to obtain injected spray structure.Pulsed air-assist liquid jet will offer rapid mixing and good liquid jet penetration.Air-assist makes a very fine droplet which generated mist-like spray.Pulsed air-assist liquid jet will introduce additional supplementary turbulent mixing and control of penetration depth into a cross-flow field.The results show that pulsation frequency has an effect on penetration,transverse velocities and droplet sizes.The experimental data generated in these studies are used for a development of active control strategies to optimize the liquid jet penetration in subsonic cross-flow conditions and predict combustion low frequency instability.     

Reprocessing of spent nuclear waste using ionic liquids

Nuclear power has once again attracted from all over the world due to many factors including the rise in oil process and environmental concerns on greenhouse gas emission resulting in global warming. However, spent fuel from nuclear power reactors is an enormous problem both from radiation hazard and economical point of view. Therefore, this review presents an overview of application of ionic liquids (ILs) in spent fuel reprocessing, particularly in the extraction of high-level radioactive aqueous waste from the processing of nuclear fuel.     

Global regulation of a class of nonlinear systems with high-order triangular type nonlinearity

The problem of global regulation is investigated for a class of nonlinear systems which contain some high-order terms. We propose a high-order scaling state-feedback controller with appropriate dynamic gains. Compared to existing results, the condition on the nonlinearity is flexible due to the freedom of choosing the bounding positive function of the nonlinearity. Thus, the nonlinear systems with some high-order nonlinearities which do not belong to existing conditions can be globally regulated.     

Effects of milk proteins and gums on quality of bread made from frozen dough

BACKGROUND: Mixtures of milk proteins and gums incorporated into bread formulations may enhance the quality of bread and retard the deterioration of frozen dough. Our objective was to investigate the effects of mixtures of milk proteins (casein (C) and whey protein (W)) and gums (sodium alginate (A) and κ‐carrageenan (K) on the quality of bread made from frozen dough. We hypothesized that bread containing milk proteins and gums would be of improved quality. Milk proteins improve texture, moisture retention and specific volume, and reduce the size of ice crystals, while gums incorporated into the bread improve moisture retention, control water mobility and prevent the growth of ice crystals, so we hypothesized milk proteins and gums would suppress the quality deterioration of bread during frozen storage. RESULTS: We found that mixtures of milk proteins and gums proved effective with regard to the maintenance of the baking quality of frozen dough. Breads containing CA had a higher specific loaf volume than the control bread. The addition of WK enhanced crumb firmness during extended frozen storage. In sensory evaluation, the addition of WA and CA contributed to the improvement of baking quality, taste, texture and acceptability. CONCLUSION: These findings are consistent with the hypothesis that mixtures of milk proteins and gums improved baking quality by reducing the deterioration of frozen dough. These results indicate that the addition of CA and WA improved the bread quality and WK could effectively be used as an anti‐staling agent in bread. Copyright © 2009 Society of Chemical Industry     

Optimization of lead- and cadmium-free front contact silver paste formulation to achieve high fill factors for industrial screen-printed Si solar cells

Screen-printed n⁺–p–p⁺ solar cells were fabricated on Cz single crystalline Si material, with a 45 Ω/sq emitter and PECVD SiNx antireflective coating with a thickness of 700 Å, using different Ag pastes and commercial leaded reference paste (CN33-462, Ferro Corp.). Ag and Al contacts were co-fired using a mass-production line equipped with mesh belt conveyer furnace systems (Centrotherm thermal solution GmbH & Co. KG). The average results for single crystalline Si solar cells (156 cm²) are: I_sc=5.043 A, V_oc=0.621 V, R_s=0.0087 Ω, R_sh=15.3 Ω, FF=0.773, and E_ff=16.45%. R_sh and fill factor values of fabricated cells were slightly higher when compared with the commercial leaded Ag paste, although cells were fabricated by metallizing the lead-free silver pastes. For the lead-free Ag paste used in this study, the line pattern continuity is retained with improved edge definition in sharp contrast to that of reference Ag paste. Average value of R_s was also equivalent approximately to that of the leaded Ag paste.     

Cube + Goss Textured Electrical Steels

After final annealing, the cube + Goss texture is stronger at the higher final thickness reduction. The annealing texture becomes stronger with the decreasing bulk sulfur content. At a fixed bulk sulfur content, the cube + Goss texture is well developed under a pure hydrogen atmosphere compared with a mixed-gas atmosphere. The excellent magnetic properties are obtained from the strip containing the bulk sulfur content of 6 ppm.     

Analysis of PLR for Shared Switch Fabrics

A modular upgrade design for packet transport switch nodes is presented where packet loss is dramatically reduced by intra‐module and inter‐module buffer sharing. This modular design offers significant cost and power reduction in a high‐data‐rate system where buffers are highly costly and power‐greedy.     

不疯魔不成活 IT粉丝集体亮相

你见过最疯狂的“粉丝”行为是什么？ 在家中为偶像建立神龛，成为偶像的跟踪者，为偶像绝食瘦身……     

Pursuing goals with others: Group identification and motivation resulting from things done versus things left undone.

This article addresses what factors best motivate individuals to work toward shared goals. We propose that when individuals do not identify highly with a group, their contributions will mimic others': An emphasis on things done will increase their contributions toward achieving a goal, because such emphasis suggests the goal is worth pursuing. Conversely, we propose that when individuals identify highly with a group, their contributions will compensate for others': An emphasis on things left undone will increase their own contributions, because missing contributions suggest insufficient progress toward a goal they already consider worthwhile. Five studies lend support to these predictions by measuring contributions to goals centered on idea generation and helping victims of various global disasters (earthquake in Haiti, wildfires in Southern California, rioting in Kenya). (PsycINFO Database Record (c) 2011 APA, all rights reserved)