Dosimetric characteristic of VVR-M reactor with respect to tritium

Translated from Atomnaya Énergiya, Vol. 67, No. 2, pp. 111–113, August, 1989.     

A distribution function for double-bit upsets

It is suggested that the chord length distribution method could be useful for predicting double-bit upset rates in certain circumstances. A chord length distribution function for simultaneous path lengths in two parallelepipeds, applicable to a unidirectional flux, is derived. A proof of the system is outlined for the case under consideration     

测定钠中杂质的手动阻塞计的研究

文章介绍了测定钠中杂质浓度的手动阻塞计的原理、装置和实验结果。为了减少测量误差,我们研究了影响准确测定阻塞温度的因素,并且找到了减少测量误差的办法。在同样的杂质饱和温度下,该阻塞计测得的高、低阻塞温度所对应的杂质浓度差是很接近的。对氧其差值为1.03ppm;对氢为0.0763ppm。     

Power-dependent dispersion in far-off-resonant raman scattering

We investigate the saturation effects of power broadening, Stark shifting, and population transfer on Stokes conversion in stimulated Raman scattering. We do not make the usual rotating wave approximation because the detuning from the next electronic state is assumed to be in the optical regime. Retaining the counter-rotating terms allows an exact determination of the pump and Stokes indexes of refraction. Steady-state solutions for the Stokes intensity and phase are obtained and the effects of making the rotating wave approximation (RWA) are discussed. Finally, we examine the behavior of these solutions for Stokes conversion in hydrogen gas when geometric propagation is appropriate.     

Computing hysteresis points of nonlinear equations depending on two parameters

A direct method is described for computing a hysteresis point (double turning point) corresponding to a cusp point of a system ofn nonlinear equations inn variables depending on two parameters. By addition of two equations a minimally extended system ofn+2 nonlinear equations is constructed for which the hysteresis point is an isolated solution. An efficient implementation of Newton's method is presented not requiring evaluations of second derivatives of the original problem. Two numerical examples show the efficiency of theQ-quadratically convergent method.     

High-voltage bridge for measuring spontaneous polarization,dielectric constants,and conductivity of ferroelectric crystals

Translated from Izmeritel'naya Tekhnika, No. 9, pp. 34–35, September, 1989.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

Analysis of a stiffener intersection eccentricity in a steel containment

Containment structures have several regions in which the continuity of the cylindrical pressure boundary is interrupted, e.g., shell penetrations, discontinuous stiffeners, and changes in the shell thickness. Significant strain concentrations can occur in these areas of discontinuity. The Sandia National Laboratories 1:8-scale steel containment equipment hatch was analyzed as an example of an eccentricity at a stiffener intersection.A portion of the as-built 1:8-scale model was modeled with the ANSYS general purpose finite element program using triangular, thin shell finite elements. The overall size of the model was determined from Saint-Venant type considerations of the stress field around the hatch. Shell elements were used to model the ring and formed stiffeners. Geometric and material nonlinear behavior were included. The model was loaded using discrete load steps up to a pressure of 165 psig. At this pressure, the maximum strain was 19.7 percent in the formed stiffener near its intersection with the ring stiffener. The finite element solution demonstrated the very localized nature of the strain field near the ring/formed stiffener intersection.In an attempt to reduce analysis costs, a small portion of the 1:8-scale model immediately surrounding the ring/formed stiffener intersection was selected for further analysis. Two smaller models, a ring/formed stiffener intersection and a ring/circular stiffener intersection, were studied. The models were significantly smaller than the regions used previously. A comparison of the two intersection models showed that the circular stiffener is a more efficient configuration.