Novel blood-compatible waterborne polyurethane using chitosan as an extender

A series of novel block polymers of polyurethane (PU) and chitosan have been prepared in two steps. The first step is the preparation of PU prepolymer, obtained from polytetramethylene oxide glycol (PTMO, M_n = 1000), isophrone diisocyanate (IPDI), and 2,2′-dimethylol propionic acid (DMPA), followed by ionizing PU prepolymer with triethylamine (TEA). The second step involves PU chain-extended by water-soluble chitosan of low molecular weight (M_n = 5000) by self-emulsion polymerization method. The sizes of the latex particles, morphology, and copolymer architecture have been characterized by dynamic light scattering (DLS), general tensile test, infrared spectroscopy (IR), surface contact angle measurement, and transmission electron microscopy (TEM). Furthermore, it shows that the addition of chitosan remarkably increases anticoagulative property of PU elastomers confirmed by the recalcification time. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of post‐treatments on the properties of porous poly(vinyl alcohol) membranes

Porous poly(vinyl alcohol) (PVA) membranes were prepared by a phase‐inversion method. The influence of chemical crosslinking and heat treatments on the swelling degree, resistance to compaction, mechanical strength, and morphology of porous PVA membranes was extensively studied. The crosslinking degree and crystallinity of the membranes, calculated from IR spectra, increased with the treatment time. The porosity, calculated on the basis of swelling experiments, showed a decreasing trend for heat‐treated membranes but remained almost at a constant value for crosslinked membranes. Such a change was further proved with scanning electron microscopy pictures. The behavior was explained by the rearrangement of PVA chains during the heat‐treatment process, which led to morphological changes in the membranes. The mechanical properties of the porous membranes in dry and wet states were measured, and a great difference was observed between crosslinked and heat‐treated membranes in the dry and wet states. The crosslinked membranes showed good mechanical properties in the dry state but became fragile in the wet state. On the contrary, the heat‐treated membranes were more flexible in the wet state than in the dry state. This change was explained by the turnaround of inner stress in the systems during the swelling process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

导向剂加入方式对Y型沸石合成的影响

以煤系高岭土为原料,采用液态补硅手段调节体系SiO2/Al2O3、导向剂两步加入法合成了Y型沸石.考察了导向剂不同加入方式对Y型沸石合成的影响.采用合理的导向剂两步加入法,特别是通过控制导向剂第二步加入的时间,可明显缩短Y型沸石的晶化时间,并有效地减少P型沸石的生成.     

SC-3000智能均流测试仪在整流供电系统中的应用

论述了均流仪在整流机组均流管理中的功效.     

星型聚合物中间体环硅氧烷核的合成研究

以甲基二氯硅烷、四甲基四乙烯基环四硅氧烷(DVi4)为原料,采用硅氢加成反应合成了星型聚合物的中问体环硅氧烷核,并用红外光谱和核磁共振谱进行了表征.反应的最佳条件是:采用预先活化、反应温度72℃、催化荆与DVi4的量之比为1.0×10-4,反应转化率可达95%,且选择性很好,产物主要为β-加成产物.     

Composite group vector space method for estimating melting and boiling point of pure organic compound

Composition Group Vector Space (CGVS) method for estimating melting and boiling point T _m , T _b of organic compound has been proposed, and the principle of this method has been elucidated. The models for estimating T _m , T _b have been established and the numerical values of relative parameters have been presented. The average percentage deviations of T _m , T _b estimation are 7.53 and 1.58, respectively, which show that the present method demonstrates significant improvement in applicability to predict the above properties, compared to conventional group methods.     

浅谈在线配粉条件下专用粉质量控制

浅述了在线配粉条件下,通过严格生产管理及改良剂应用等相关措施,控制好专用粉质量的措施.包括落实ISO质量管理体系,加强原料的质量控制和预粉、粉路的测定,生产过程中要注意小麦清理与着水、生产设备和现场管理、员工的技术水平因素等.