高功率双工旋转场移相器

旋转场移相器具有移相精度高(均方根误差可小于1°)和温度稳定性好等特点,通过改进射频传输结构,可大大提高他的功率容量。利用旋转场移相器的互易特性和铁氧体圆极化器的非互易特性,设计出高功率双工旋转场移相器。其双工特性可将收/发信号分开,实现移相器和环行器的双重功能,用于天线的收发通道等场合时,可省去一个高功率环行器,结构紧凑。分析了双工旋转场移相器的工作原理,阐述了高功率应用下的设计方法,推导出了管状铁氧体的相移量计算公式,按此方法设计了实用的器件,并给出了试验数据。     

Analysis of tungsten and titanium migration during ESD contact burnout

A physical and chemical analysis of a machine model (MM) electrostatic discharge (ESD) failure in a silicon circuit was carried out. Focused ion beam (FIB) was used to make cross sections through the region of contact burnout. The resulting samples were analyzed using scanning electron microscopy (SEM) and two-dimensional (2-D) auger electron spectroscopic (AES) mapping. It is shown for the first time that both titanium (Ti) and tungsten (W) migrated throughout the melted silicon filament. Large pellets of the W plug were embedded in the bulk silicon but only on the cathode side of the junction. Mechanisms are discussed to explain these phenomena. These involve the melting of titanium disilicide (TiSi/sub 2/), dissolution of Ti and W in the molten silicon and the formation of W pellets through electromigration at temperatures below /spl sim/1800 K.     

Ab-initio primitive cell parameters from single convergent-beam electron diffraction patterns: a converse route to the identification of microcrystals with electrons.

A new method for the ab initio derivation of Buerger-reduced primitive cell parameters from coordinate measurements of spots on single convergent-beam electron diffraction (CBED) patterns is described, which does not involve trial-and-error. The pattern can be taken along any zone axis, and misorientations of the crystallite by as much as a few degrees are taken into account without loss of accuracy. This derivation of cell parameters by least-squares analysis of the measurements has been automated in a program called NRCBED. Present accuracy is about 1% on lengths and 2 degrees on angles, but could be significantly improved by modelling projector lens aberrations, or by using a microscope without a projector lens. With present technology, it is possible to obtain a CBED pattern and a semi-quantitative energy-dispersive X-ray (EDX) analysis simultaneously from a single microcrystal a few hundred Angstr?ms across. It becomes therefore possible to identify the material of the crystal on a single CBED pattern: a cell parameter database for known compounds is searched with the primitive cell parameters obtained in the above way, and with a mask describing the EDX results qualitatively. Feasibility is demonstrated on a crystallite of CeO2 500 Angstr?ms across. With this new approach, trial-and-error should disappear from the solution of other long-standing problems: interpretation of X-ray powder patterns for new compounds in the presence of impurity lines, or in the case of multiple phases should become straight-forward.     

Highly integrated direct conversion receiver for GSM/GPRS/EDGE with on-chip 84-dB dynamic range continuous-time /spl Sigma//spl Delta/ ADC

This paper describes a highly digitized direct conversion receiver of a single-chip quadruple-band RF transceiver that meets GSM/GPRS and EDGE requirements. The chip uses an advanced 0.25-/spl mu/m BiCMOS technology. The I and Q on-chip fifth-order single-bit continuous-time sigma-delta (/spl Sigma//spl Delta/) ADC has 84-dB dynamic range over a total bandwidth of /spl plusmn/135 kHz for an active area of 0.4 mm/sup 2/. Hence, most of the channel filtering is realized in a CMOS IC where digital processing is achieved at a lower cost. The systematic analysis of dc offset at each stage of the design enables to perform the dc offset cancellation loop in the digital domain as well. The receiver operates at 2.7 V with a current consumption of 75 mA. A first-order substrate coupling analysis enables to optimize the floor plan strategy. As a result, the receiver has an area of 1.8 mm/sup 2/.     

对索风营水电站坝址区堆积体勘察设计的几点认识

乌江索风营水电站坝址区分布有7个堆积体,其成因有崩塌堆积、蠕变-拉裂-崩解堆积、塌滑堆积及混和堆积等.在勘察过程中采用了地质测绘、钻探、硐探、物探、科研试验等多种勘察方法与手段,在勘察成果基础上对堆积体稳定性进行了分析,并结合对工程的不同影响提出了相应的工程处理措施.     

A3钢的工业大气腐蚀

在辽宁省工业城市进行 A3钢大气暴露试验。两年后测出不同地点腐蚀率。依据所记录的各试验点的气象数据和污染数据,讨论了 A3钢的大气腐蚀规律。     

MIMO系统中的分组全分集全码率空时编码

针对未编码的多输入多输出（MIMO，Multi—Input Multi—Output）系统，提出一种复杂度适中的分组全分集全码率（GFDFR，Group—wise Full Diversity Full Rate）空时编码方案。该方案通过在发送端进行天线分组，各组独立编码，减小全分集全码率（FDFR，Full Diversity Full Rate）编码块的大小从而降低系统编解码复杂度；在频率选择性信道中，进一步对子载波分组进行独立编码，获得频率分集（或多径分集），以适中的复杂度在不降低系统分集度的情况下保证了信息的全码率传输，是一种在MIMO信道中极具实用价值的空时编码方案。     

A distributed approach for access and visibility task with a manikin and a robot in a virtual reality environment

This paper presents a new method, based on a multi-agent system and on a digital mock-up technology, to assess an efficient path planner for a manikin or a robot for an access and visibility task taking into account ergonomic constraints or joint and mechanical limits. In order to solve this problem, the human operator is integrated in the process optimization to contribute to a global perception of the environment. This operator cooperates, in real time, with several automatic local elementary agents. The result of this work validates solutions through the digital mock-up; it can be applied to simulate maintainability and mountability tasks.     

Elastic properties of polycrystalline gold thin films: Simulation and X-ray diffraction experiments

The elastic behavior of supported gold thin films has been studied using a framework in which the elastic interaction between grains and the actual structure of the film (i.e. preferential grain orientation and grain shape) are taken into account. Experiments were carried out using synchrotron X-ray diffraction combined with in-situ tensile testing and thereafter, no assumptions on the residual stress state and on the stress-free lattice parameter a₀ have to be made. Modeling of grain elastic interactions is based on the extension of Eshelby-Kröner model, which allows for estimating the elastic behavior of polycrystals considering the texture and the shape of the crystallites. Flat-disc shaped grains arrangement is shown to yield the best representation of the elastic behavior of the fiber-textured gold thin films composed of columnar grains. This non-intuitive representation results from free-surface effect.     

In situ regeneration of the Ni-based catalytic reformer of a 5 kW PEMFC system

The paper reports the results of on-site regeneration catalytic bed of the natural gas reformer in a 5 kW PEM fuel cell system. The Ni catalyst previously poisoned by sulphur from the available natural gas, could be re-activated by injection of pure water steam, following the method developed for industrial reformers using the same metal catalyst: this method was shown to be perfectly efficient, provided no natural gas was fed during the operation. Results of the tests conducted are presented and discussed in relation to published data on S-sorption on Ni surfaces.