Structure and catalytic properties of dealuminated modified zeolites Y

The effect of treatment with a zirconyl nitrate aqueous solution on the structure; the hydroxyl-layer constitution; and the adsorptive, acid, and catalytic properties of dealuminated zeolite Y was studied. The zeolite was prepared by boiling NH₄Y in an ethylenediaminetetraacetic acid disodium salt solution followed by ion exchange with ammonium chloride and calcination in a 100% steam flow at 750°C. X-ray diffraction, IR spectroscopy, and DTA data show the formation of an ultrastable form of zeolite Y. The incorporation of zirconium in zeolite led to an increase in the proportion of strong acid sites, thus raising the yield of cracking products during n-hexane conversion tested on platinum-containing catalyst samples.     

Disc filtration for separation of flocs from a moving bed bio-film reactor.

A Discfilter with 10 and 18 microm filter openings, respectively, was placed in parallel to a flotation plant for separation of biological flocs from a post-denitrifying Kaldnes Moving Bed Process, the last treatment step at the municipal wastewater treatment plant at Sj?unda, Malm?, Sweden. The effluent concentrations from the 10 and 18 microm filter were 2-5 and 2-8 mg SS L(-1), respectively, which is comparable to, or better than, the flotation plant. Comparison with experiences from activated sludge plants shows that the Discfilter works especially well after the Kaldnes process. Particle size distribution (PSD) studies show that particles larger than the filter openings of 10 and 18 microm are separated with approximately 90% efficiency, whereas most of the smaller particles pass the filter. This fact indicates that the major particle separation mechanism is physical blocking. These findings point to the possibility of improving the prediction of the separation efficiency by combining measurements of turbidity and suspended solids with particle size analysis.     

Hydrogen degradation of steels in gas mains after long periods of operation

We study the degradation of the mechanical and corrosion properties of 17G1S steel in gas mains as a result of operation for 28–40 yr. We reveal the simultaneous decrease in its strength and hardness, on the one hand, and impact toughness and crack resistance, on the other hand. The indicated parameters prove to be most sensitive to the in-service degradation of the metal. The degradation of steel leads to the increase in the strain-hardening coefficient and the appearance of the yield plateau in the tensile stress-strain diagram and causes the appearance of sensitivity to hydrogen embrittlement increasing in the process of operation. We analyze the role of absorbed hydrogen affecting the mechanism of strain aging and responsible for the appearance of defects. It is shown that the polarization resistance can be used not only for monitoring of the corrosion state of gas pipelines but also for the prediction of changes in their mechanical properties in the process of operation. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 43, No. 5, pp. 97–104, September–October, 2007.     

Segregation band formation in Al-Si die castings

Banded defects are often found in high-pressure die castings. These bands can contain segregation, porosity, and/or tears, and changing casting conditions and alloy are known to change the position and make-up of the bands. Due to the complex, dynamic nature of the high-pressure die-casting (HPDC) process, it is very difficult to study the effect of individual parameters on band formation. In the work presented here, bands of segregation similar to those found in cold-chamber HPDC aluminum alloys were found in laboratory gravity die castings. Samples were cast with a range of fraction solids from 0 to 0.3 and the effect of die temperature and external solid fraction on segregation bands was investigated. The results are considered with reference to the rheological properties of the filling semisolid metal and a formation mechanism for bands is proposed by considering flow past a solidifying immobile wall layer.     

Review on testers for measuring flow properties of bulk solids

 The author was asked by the International Fine Particle Research Institue (IFPRI) to write a critical review on shear testers for IFPRI-members. The review was delivered to IFPRI in summer 1999. Following the contract with IFPRI it was not allowed to publish the review elsewhere for at least two years. Granular Matter invited the author to submit the review in the original form; during the refereeing process (besides other changes) it turned out that some remarks should be added here for clarification: - Since 1999, the author is not aware of a really new device for testing bulk solid properties, which could lead to a change of the general comments and conclusions provided in the review. It was argued, that the review is referring too much to the work of Jenike, while the works of Johanson and Peschl were not adequately cited. Both are excellent engineers with a lot of experience, but their basic ideas are not available in published form, and if, they are not set in relation to alternative approaches so that an objective comparison in detail would be a future research issue rather than a topic in this report. A discussion on the influence of electrostatic charges was missing. There hardly is an influence, since the particles are in continuous contact. Only with non-conducting plastic particles electrostatic charges could cause problems. But no relevant experiments and results are known. In closed systems, the effect of electric charges is thus mainly neglected, but it is clear that electrostatic forces are eminent in flows with a free surface – an issue not addressed in this review. Received: 1 November 2002     

It takes two to mimic: Behavioral consequences of self-construals.

The present studies demonstrated the moderation of self-construal orientation on mimicry. Recent research has indicated that an interdependent self-construal is associated with assimilation of the other to the self whereas an independent self-construal is associated with minimizing the influence of others on the self (H. R. Markus & S. Kitayama, 1991; D. Stapel & W. Koomen, 2001). Therefore, the authors hypothesized that an interdependent self-construal would be associated with more mimicry than an independent self-construal. When self-construal orientations were experimentally primed. as in Studies 1 and 2, independent self-construals produced less nonconscious mimicry than interdependent self-construals. When self-construals were examined as cultural differences with either a chronically dominant independent (Americans) or interdependent (Japanese) construal of the self, these results were replicated. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Combined time and wavelength multiplexing technique of optical fiber grating sensor arrays using commercial OTDR equipment

The use of a commercial optical time domain reflectometry device for simultaneous wavelength and time domain multiplexing of fiber-optic Bragg grating sensors is proposed and demonstrated. The realization of such systems provides an inexpensive way of interrogating several hundreds of sensors in a single fiber. Strain resolution of 30 /spl mu/m/m over a strain measuring range of 0.5% was obtained.     

One-dimensional diffuser based on a thick layer of dichromated gelatin

A new diffuser capable of scattering light in one direction (one-dimensional diffuser) has been developed and experimentally tested. The diffuser is formed in a thick layer of dichromated gelatin. The scattering indicatrices of the diffuser measured in two mutually perpendicular directions are presented. It is demonstrated that the indicatrix width in one direction is significantly greater than that in the perpendicular direc-tion. However, no zero-order diffraction has been observed. The proposed one-dimensional diffuser exhibits close scattering indicatrices for reading at a wavelength of 0.44 and 0.63 μm.     

Grain refinement of Al-7Si alloys and the efficiency assessment by recognition of cooling curves

Under sand cup solidification condition, the influence of Ti, B concentration, and holding time on the grain size of a high-purity Al-7Si alloy has been systematically studied. It is found that the grain size decreases rapidly at lower Ti or B additions, and is almost constant at the higher concentrations. For Al-3B refined Al-7Si alloys, the grain size increases at the initial period of holding time, and then rapidly becomes independent of holding time; while for Al-7Si alloys refined with Al-5Ti-1B, the grain size increases with holding time throughout. To evaluate the refinement efficiency, a new method named “intelligent evaluating of melt quality by pattern recognition of thermal analysis cooling curves” has also been introduced in this article. The results show that comparing the cooling curve of the evaluated melt with those in a database to find the most similar one to it can precisely assess the grain refinement efficiency of the measured Al-7Si alloy. In addition, the influence of Ti, B addition levels, and pouring temperatures on some characteristic parameters of cooling curve has also been discussed.     

Electrospray droplet sources for thin film deposition

Electrospraying utilises electrical forces for liquid atomisation. Droplets obtained by this method are highly charged to a fraction of the Rayleigh limit. The advantage of electrospraying is that the droplets can be extremely small, down to the order of 10’s nanometres, and the charge and size of the droplets can be controlled to some extent be electrical means. Motion of the charged droplets can be controlled by electric field. The deposition efficiency of the charged spray on an object is usually higher than that for uncharged droplets. Electrospray is, or potentially can be applied to many processes in industry and in scientific instruments manufacturing. The paper reviews electrospray methods and devices, including liquid metal ion sources, used for thin film deposition. This technique is applied in modern material technologies, microelectronics, micromachining, and nanotechnology.