Precise identification of moving vehicular parameters based on improved glowworm swarm optimization algorithm

This paper proposes an indirect method for the identification of moving vehicular parameters using the dynamic responses of the vehicle. The moving vehicle is modelled as 2-DOF system with 5 parameters and 4-DOF system with 12 parameters, respectively. Finite element method is used to establish the equation of the coupled bridge–vehicle system. The dynamic responses of the system are calculated by Newmark direct integration method. The parameter identification problem is transformed into an optimization problem by minimizing errors between the calculated dynamic responses of the moving vehicle and those of the simulated measured responses. Glowworm swarm optimization algorithm (GSO) is used to solve the objective function of the optimization problem. A local search method is introduced into the movement phase of GSO to enhance the accuracy and convergence rate of the algorithm. Several test cases are carried out to verify the efficiency of the proposed method and the results show that the vehicular parameters can be identified precisely with the present method and it is not sensitive to artificial measurement noise.     

基于Opencv的絮体颗粒跟踪与沉速测量系统研究

针对饮用水处理过程混凝剂投加量对处理结果的直接影响,提出了一个以絮体的沉降速度(作为主控,等效粒径、数量等参数作为辅控的多源数据融合的混凝剂投药模型。本文基于Open CV机器视觉库,以VS2010为平台,采用C++语言,编写絮体检测和沉降速度测量在线系统的软件,实现了絮体各个参数和沉降速度的实时监测。     

基于Fluent的圆柱齿轮流量计的密封性仿真分析

通过对圆柱齿轮流量计进行二维简化建模,用Fluent仿真软件的ICEM CFD模块进行网格划分,利用Fluent仿真软件对圆柱齿轮流量计进行了计算和密封性的仿真分析,得出了其速度矢量分布图,并且给出了各泄漏量的计算公式和每种泄漏所占泄漏总量的百分比,即为以后的整个流量计的设计提供理论依据。,提高流量计的寿命具有重要意义。同时还省去了大量的人工计算过程,极大地加快了计算速度。     

Composite bending-dominated hollow nanolattices: A stiff,cyclable mechanical metamaterial

Manufacturing ultralight and mechanical reliable materials has been a long-time challenge. Ceramic-based mechanical metamaterials provide significant opportunities to reverse their brittle nature and unstable mechanical properties and have great potential as strong, ultralight, and ultrastiff materials. However, the failure of ceramics nanolattice and degradation of strength/modulus with decreasing density are caused by buckling of the struts and failure of the nodes within the nanolattices, especially during cyclic loading. Here, we explore a new class of 3D ceramic-based metamaterials with a high strength–density ratio, stiffness, recoverability, cyclability, and optimal scaling factor. Deformation mode of the fabricated nanolattices has been engineered through the unique material design and architecture tailoring. Bending-dominated hollow nanolattice (B-H-Lattice) structure is employed to take advantages of its flexibility, while a few nanometers of carbonized mussel-inspired bio-polymer (C-PDA) is coherently deposited on ceramics’ nanolayer to enable non-buckling struts and bendable nodes during deformation, resulting in reliable mechanical properties and outperforming the current bending-dominated lattices (B-Lattices) and carbon-based cellulose materials. Meanwhile, the structure has comparable stiffness to stretching-dominated lattices (S-Lattices) while with better cyclability and reliability. The B-H-Lattices exhibit high specific stiffness (>10⁶?Pa·kg^?1·m^?3), low-density (～30?kg/m³), buckling-free recovery at 55% strain, and stable cyclic loading behavior under up to 15% strain. As one of the B-Lattices, the modulus scaling factor reaches 1.27, which is lowest among current B-Lattices. This study suggests that non-buckling behavior and reliable nodes are the key factors that contribute to the outstanding mechanical performance of nanolattice materials. A new concept of engineering the internal deformation behavior of mechanical metamaterial is provided to optimize their mechanical properties in real service conditions.     

基于数字兆欧表自动切换档位的研究与实现

随着电力、电气设备的日益复杂化,对于其安全性能也有了更高的要求,数字兆欧表作为测量绝缘阻值的重要工具,已在工业领域中广泛应用;为了满足测量精度以及兆欧表的可靠性,通过基于S3C2440的嵌入式平台,提出了一种基于数字兆欧表的自动切换档位的实现方案,以达到更加精确的测量;此方案通过判断采集到的电压值选择相应的采样电阻来实现,并结合硬件平台和软件设计,分别介绍了驱动程序和应用程序的编写与测试,并很好地应用到了实际电路中;经测试,能够达到预期的效果,测量精度高,测量误差控制在±2%。     

电火花打孔加工系统

本文介绍了电火花打孔加工系统的工作原理和组成、并对系统中的高压脉冲产生电路的设计进行了详细的阐述     

Property-microstructure correlation in in situ formed Al2O3, TiB2 and Al3Ti mixture-reinforced aluminium composites

The in situ formed Al₂O₃, TiB₂ and Al₃Ti mixture-reinforced aluminium composites were successfully fabricated by the reaction sintering of the TiO₂-B-Al system in a vacuum. With increasing boron content in the TiO₂-B-Al system, the amount of generated TiB₂ in the composites increased and Al₃Ti content decreased. At the same time the distribution uniformity of the in situ formed Al₂O₃ and TiB₂ particulates was obviously improved, and the size of the Al₃Ti particles was reduced. The in situ Al₂O₃ and TiB₂ particulates had sizes from 0.096–1.88 m. The interface between the in situ formed particulates and the aluminium matrix was clean, and no consistent crystallographic orientation relationship was found. The strength and elastic modulus of the composites was significantly improved by lowering the Al₃Ti content. When the boron content in the TiO₂-B-Al system rose, the morphology of the tensile fracture surface of the composites was changed from large fractured Al₃Ti blocks and fine dimples, to fine dimples and pulled-out particulates. The strengthening and fracture of the composites have been modelled.     

Infective endocarditis complicated with rapidly progressive glomerulonephritis: a case report

Despite a general national decline in criminal activities in the 1990s, juvenile criminal offenses continue to increase, (including violent, property, and delinquency acts). In addition increased numbers of children are being held in juvenile jails. It is all but impossible for pediatric health providers to think that "their patients" and "their practices" are immune from the epidemic of crime that affects and is caused by "just kids."