岩溶区石灰石矿山溶洞探测分析

江西南城南方水泥有限公司蒋源矿区矿山开采过程中发现了溶洞,并利用空洞仪（一种物探设备）对溶洞探测并采集数据以及使用RTK对溶洞分布情况进行坐标数据采集。经过对空洞仪成像分析,结合现场采集的数据制作出溶洞空间分布图,精确掌握溶洞发育的规模、空间状态,对制定岩溶发育区域矿山开采、爆破施工方案、应急预案,以及确保施工安全起到了非常重要的作用。     

Effects of Ultrasonic Vibration on Material Flow and Thermal Cycles in Friction Stir Welding of Dissimilar Al/Mg Alloys

Comparative experiments are performed in friction stir welding (FSW) of dissimilar Al/Mg alloys with and without assistance of ultrasonic vibration. Metallographic characterization of the welds at transverse cross sections reveals that ultrasonic vibration induces differences in plastic material flow in two conditions. In FSW, the plastic material in the peripheral area of shoulder-affected zone (SAZ) tends to flow downward because of the weakening of the driving force of the shoulder, and a plastic material insulation layer is formed at the SAZ edge. When ultrasonic vibration is exerted, the stirred zone is divided into the inner and outer shear layers, the downward material flow trend of the inner shear layer disappears and tends to flow upward, and the onion-ring structure caused by the swirl motion is avoided in the pin-affected zone. By improving the flow behavior of plastic materials in the stirred zone, ultrasonic vibration reduces the heat generation, accelerates the heat dissipation in nugget zone and changes the thermal cycles, thus inhibiting the formation of intermetallic compound layers.

     

矿山磨光球用钢XK5159H的生产试制

XK5159H钢连铸连轧棒材用于制造矿山磨光球，对于钢的纯净度、低倍组织、探伤结果及DI值等均有严格的要求，很难控制。我们通过制定内控化学成分及合理的工艺路线，使生产试制一次成功。     

SiCp/Cu包覆粉体及其热沉材料的制备

采用化学镀铜工艺制备了Cu包覆SiCp复合粉体,并对复合粉体的组成和形貌进行了分析.同时,利用制得的复合粉体,结合适当的热压烧结工艺制备了Cu-35SiCp热沉材料,并对热沉材料的微观组织和热物理性能进行了研究.结果表明,SiCp颗粒在热沉材料的基体中均匀分布,界面结合良好.在试验条件下,Cu-35SiCp热沉材料的导热系数为165.7 W/(m·K),30～200 ℃温度区间内的热膨胀系数为15.1×10-6/K.     

SBTV铁电材料的制备和微观组织结构

采用固相反应法合成了SrBi2Ta2O9(简称SBT)和V掺杂SrBi2Ta2O9(简称SBTV)陶瓷,通过TG-DTA、XRD、SEM、TEM等技术手段研究了材料的烧结工艺、相组成和微观组织结构.研究表明V2O5是一种很好的助烧剂,掺杂后材料的烧结温度可降低200℃烧结后纯SBT均为单一的钙钛矿相SBT;掺杂后2种成型工艺所制备的SBTV除了生成少量Bi4(V2O11)外,仍主要由钙钛矿相组成;同时所有的材料都发生了一定程度的择优取向.掺杂后材料的晶粒形态发生变化棒状转化为片状.同时V掺杂后引起了晶格畸变,产生应变,SBTV材料在透射中观察到具有α-边界特征的90°畴.     

Effect of temperature on anodic behavior of 13Cr martensitic steel in CO2 environment

The corrosion behavior of 13Cr martensitic stainless steel in a CO₂ environment in a stimulated oilfield was studied with potentiodynamic polarization and the impedance spectra technique. The results showed that the microstructure of the surface scale clearly changed with temperature. This decreased the sensitivity of pitting corrosion and increased the tendency toward general (or uniform) corrosion. The capacitance, the charge transfer resistance, and the polarization resistance of the corrosion product scale decrease with increasing temperature from 90 to 120 °C, and thus the corrosion is a thermal activation controlled process. Charge transfer through the scale is difficult and the corrosion is controlled by a diffusion process at a temperature of 150 °C. Resistance charge transfer through the corrosion product layer is higher than that in the passive film.     

Study on Tribological Properties of Polytetrafluoroethylene Drawn Uniaxially at Different Temperature

Summary: Wear behavior correlations with morphology have been established from polytetrafluoroethylene (PTFE) drawn at 200, 327, and 375 °C with draw ratio about 4. The friction coefficient and wear rate for PTFE drawn at 327 °C are lower and the wear rate is lower than that of undrawn PTFE by about 30%. The structures of samples were characterized by scanning electron microscope (SEM), DSC, and wide angle X‐ray diffraction (WAXD). Results indicate that the debris morphologies of samples are different. The differences in the tribological behavior of undrawn and drawn samples were attributed to the improvement of the degree of the crystalline, fibrillation, and orderliness by drawing, especially, for PTFE drawn at 327 °C. The orderliness of molecular arrangement along the drawn direction is also higher for PTFE drawn at 327 °C than those of PTFE drawn at 200 and 375 °C, respectively. Therefore, the intensity of covalent bond along drawn direction is higher. The shear resistance and the deformability of the material are greatly improved and the size of the wear breakage unit decreases, which results in a good tribological property for PTFE drawn at 327 °C.

SEM morphology of fractured surface perpendicular to the draw direction for PTFE drawn at 327 °C.     

改性低毒脲醛树脂的合成及性能研究

采用六亚甲基四胺做催化剂，加入聚乙烯醇（PVA）、三聚氰胺和硫脲作为改性剂，通过降低甲醛与尿素物质的量比、采用尿素分批加入的合成方法，制备出改性低毒的脲醛树脂（UF），使游离甲醛质量分数低于0．30％；采用捏合和模压成型方法，将改性和普通UF树脂分别与剑麻纤维（SF）制备UF／SF共混复合材料，研究了复合材料的力学性能和吸水性能。结果表明，甲醛和尿素物质的量比为1．1时，游离甲醛质量分数降低到0．16％；甲醛和尿素物质的量比为1．2时，三聚氰胺、PVA及硫脲加入量分别为尿素总量的2．0％，1．5％，1．0％（质量分数）时，游离甲醛质量分数降低到了0．10％，粘度达到0．41Pa·S，贮存期大于80d；改性UF／SF复合材料的性能比普通UF／SF复合材料的冲击性能和耐磨性能分别提高了114％和261％。     

Trusted Integrated Circuits: The Problem and Challenges

Hardware security has become more and more important in current information security architecture. Recently collected reports have shown that there may have been considerable hardware attacks prepared for possible military usage from all over the world. Due to the intrinsic difference from software security, hardware security has some special features and challenges. In order to guarantee hardware security, academia has proposed the concept of trusted integrated circuits, which aims at a secure circulation of IC design, manufacture and chip using. This paper reviews the main problems of trusted integrated circuits, and concludes four key domains of the trusted IC, namely the trusted IC design, trusted manufacture, trusted IP protection, and trusted chip authentication. The main challenges in those domains are also analyzed based on the current known techniques. Finally, the main limitations of the current techniques and possible future trends are discussed.     

腐植酸物质对盐碱化中低产田土壤理化性质及玉米影响的研究

通过田间试验探讨了复合改良制剂、草炭、风化煤等腐植酸类物质施用对盐碱化中低产田土壤理化性质及生长作物的影响，结果表明：复合改良制剂、草炭、风化煤施用对土壤理化性质均有积极的影响，与对照相比达到显著水平。玉米产量的方差分析表明，复合改良制剂处理与草炭、风化煤等处理差异显著，与对照差异极显著，增产率均达到30．67％以上。