改进异步电机直接转矩控制系统的仿真研究

本文介绍了直接转矩控制系统的控制原理,并针对基于直接转矩控制的异步电动机运行时存在较大的电流及转矩脉动问题,提出一种新的控制方案,并基于Matlab 6.5对这种新方法进行仿真,仿真结果表明该方案能有效的解决电流及转矩脉动的问题.     

碳纤维复合材料柔性连续抽油杆开发及应用

碳纤维柔性连续抽油杆选用高性能碳纤维 ,以环氧树脂胶液为基体材料 ,添加一定配比的固化剂、促进剂和脱模剂 ,采用拉挤成型工艺制成 ,其开发的关键技术是连续成型、连接接头和安全保险装置。现场应用试验表明 ,TXC— 1、TXC— 2、TXC— 3三种规格的碳纤维柔性连续抽油杆能可靠应用于泵挂深度分别为 12 0 0、 180 0、 30 0 0m的直井和斜井中 ,实测比钢抽油杆节电 ,日产油量提高 。节能增产效果显著。     

金属基复合材料的热残余应力力学模型研究进展

金属基复合材料在高温制备的冷却过程中或热处理过程中由于组分间热膨胀系数（CTEs）的差异会产生较大的热残余应力，热残余应力对复合材料的宏观性能有着重要的影响。本文综述了分析金属基复合材料热残余应力的有限元模型和解析模型等理论模型，并指出有待深入研究的问题。     

化学气相沉积铜薄膜研究进展

本文综术了集成电路工艺的Cu布线中Cu薄膜化学气相沉积(CVD)的研究背景,详细介绍了CVD生长Cu金属薄膜的国内外研究进展及CVD对前趋物的要求,并对前趋物的一些物理、化学性质进行了总结,最后,对薄膜沉积的计算机摸拟作了简要介绍。     

Level set and geodesic active contours based measurement of material removal between serial sections

The measurement of the thickness of material removed between serial sections is a crucial step of three-dimension reconstruction. Geodesic active contours is an efficient method for contour detection of objects on an image. The indents on the SiC/Al composite micrographs are segmented by using level set and geodesic active contours. After getting the contours of the indents, we calculate the distance from the uppermost pixel to the lowermost pixel to get the vertical diagonal length, and calculate the distance from the leftmost pixel to the rightmost pixel to get the horizontal diagonal length of each contour. Then the final length of each diagonal is acquired by averaging the vertical diagonal length and the horizontal diagonal length, respectively. The Vickers’ indenter is made by a square pyramidal-shaped diamond with opposite faces at an angle of 136°, so the thickness of material removed between two serial sections and the length difference of the diagonals on the two serial sections has a definite geometrical relation. Thus the thickness of material removed between two serial sections is acquired using the geometrical relation.     

大型储罐基础非平面倾斜问题的探讨

大型储罐因基础产生非平面倾斜而影响其正常使用的情况在工程中时有发生,文章通过对某油罐工程中基础沉降观测结果的分析,探讨了储罐基础产生非平面倾斜的原因。相邻储罐之间的相互影响、充水预压未达到规范要求以及地基处理措施不当是引起储罐基础非平面倾斜的主要因素。针对相邻储罐间的相互影响,根据现行《石油化工企业设计防火规范》和《石油化工企业钢储罐地基与基础设计规范》的规定,提出以下建议:储罐布置的净距除应满足防火规范规定外,有条件时也应适当考虑对基础沉降的影响,当采用复合地基时,相邻储罐间的净距不宜小于0.6 D;当占地面积成为主要矛盾,储罐间的净距只能限制在防火规范规定的最小范围时,在地基处理时就应采取有效措施,以尽可能减少相邻储罐的相互影响。     

GPS高程在水利水电工程的应用与探讨

GPS技术的全方位发展,改变了传统的测量方法,在提供高精度的平面控制网时,GPS高程也被技术突破,达到相当于平面控制精度,该文提出在局部较平坦测区以GPS拟合高程代替传统的四等水准高程,推广应用GPS三维技术的新发展,达到更好的时效性。     

Dielectric and piezoelectric properties of Pb(Ni1/3Nb2/3)O3–PbTiO3–PbZrO3 ceramics modified with bismuth and zinc substitutions

The dielectric and piezoelectric properties of the (Pb_0.985Bi_0.01)(Ni_1/4Zn_1/12Nb_2/3)_x- (Zr_σTi_1-σ)_1-xO₃ piezoelectric ceramic system (0.2 ≤ x ≤ 0.7, 0.1 ≤ σ ≤ 0.9) were systematically investigated. The results showed that, after poling, the dielectric constant, ε ₃₃ ^T , increased for the tetragonal compositions but decreased for the rhombohedral compositions. Furthermore, high values of ε ₃₃ ^T and piezoelectric modulus, d ₃₁ were found for the compositions along the extension of the morphotropic phase boundary. The highest values of the planar electromechanical coupling factor, K _p, and the piezoelectric modulus, d ₃₁, were found to be 0.70 and − 274 × 10^-12 C N^-1, respectively. The Curie temperature, remanent polarization, coercive field and the lattice constants of the a and c axes in relation to the Pb(Ni_1/3Nb_2/3)O₃ content and the Zr/Zr + Ti ratio were also determined. This revised version was published online in November 2006 with corrections to the Cover Date.     

激光加热在Al2O3/Ti系梯度功能材料制备过程中的作用及机理

梯度功能材料是一种界面连续化的新型复合材料,本文研究了激光加热在合成Al2O3/Ti系梯度功能材料过程中的作用和机理,同时用激光大光斑加热方法制备出直径11mm厚度3mm完整的FGM试样并加以分析,以及首次采用在试样中埋设微细热电偶成功地测出了激光加热造成的温度梯度分布。