SO2转化温度异常情况分析

结合凤山实业总公司硫酸车间 SO2 转化系统的具体工艺流程 ,分析近几年转化系统出现温度不正常的原因 ,提出解决方法     

南水北调西线工程可调水量分析

在受水区缺水形势严峻的情况下，引水工程可调水量的确定主要与三个因素有关：一是引水河流及引水坝址径流量；二是坝址上下游用水要求；三是引水水库工程规模。在考虑各种因素影响后，提出各引水坝址可调水量占坝比径流量的比例在70％左右比较合适，按现阶段推荐的两种方案，可调水量可达160亿－170亿m^3.     

邻苯二甲酸酯鼓泡生物降解

该课题测试了邻苯二甲酸酯类化合物的鼓泡生物降解行为。结果表明，邻苯二甲酸酯的降解速率常数（kb)与其烷基链长度之间存在良好的相关性，kb=0.0009x^2-0.019x 0.1123，相关系数r=0.9906；浓度超过500mg/L时，邻苯二甲酸二乙酯可抑制自身的生物降解；中间产物邻苯二甲酸浓度超过50mg/L时，也对邻苯二甲酸二乙酯的生物降解有明显的抑制作用。     

如何掌握印刷压力

<正> 一、印刷压力的概念与作用 印刷的过程,从某种意义上讲,是解决油墨与纸张之间矛盾的过程。要将印版上图文处的油墨转移到承印物上,就必须施加一定的力,即所谓的印刷压力。它在印刷中具有重要的作用。 1.保证粗糙的印刷面完全接触 纸张、橡皮布、印版的表面均成粗糙微孔状。对这些粗糙表面,必须在一定的压力作用下,使其受     

宝钢2号高炉4号热风炉凉炉实践

对宝钢2号高炉4号热风炉凉炉的原因、凉炉的前期族备工作、凉炉的设备和方法以及凉炉的实际效果进行了总结。通过这次凉炉实践，取得了一些有价值的经验，这些经验对今后宝钢砖硅热风炉的凉炉具有重要的参考意义。     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

催化裂化汽油选择性加氢脱硫催化剂RSDS-1的开发

介绍了用于催化裂化汽油选择性加氢脱硫催化剂RSDS-1的研究开发，考察了载体、活性组元、金属原子比以及助剂对催化剂选择性的影响。研究结果表明，催化裂化汽油中烯烃的加氢饱和受扩散限制；Co—Mo组合对烯烃饱和的能力相对较弱；较高的Co／Mo原子比有利于提高催化剂选择性；助剂的加入对催化剂选择性有明显的影响；RSDS—1催化剂用于催化裂化汽油选择性脱硫，对不同原料油适应性好，脱硫率可达80％，RON损失小于2个单位，且可长周期稳定运转。     

兰州重离子加速器大型真空室

已建成的兰州重离子加速器的真空室是一个大型整体结构的超高真空容器,直径约10m,高4.5m,重65000kg,内表面积211m~2,容积100m~3,工作真空度为5×10~(-5)Pa。采用有限单元法在计算机上用SAP-5C程序对真空室受力分析进行了计算。真空室结构材料选用瑞典Uddeholm钢厂生产的316 L 超低碳不锈钢。承制此大型容器的是航天工业部风华机器厂。由于结构庞大,首先将真空室分成八大块和几小块在工厂制造,然后运至现场焊制成一整体容器并进行机械加工。所有密封焊缝均用着色渗透液,X-射线探伤和氦质谱探漏仪进行检查和探漏。     

Residual toughness of poly(acrylonitrile-butadiene-styrene) (ABS) after fatigue loading—effect of uniaxial fatigue loading

Toughness variation of non-notched poly(acrylonitrile-butadiene-styrene) (ABS) subjected to uniaxial fatigue loading was investigated. The experiments were conducted by applying fatigue loading to strip specimens first, from which dog-bone specimens were machined. The dog-bone specimens were tested to measure the strain for the on-set of fracture, named cracking strain here, thus to monitor the toughness change due to the fatigue loading.The test results showed that the fatigue loading caused the toughness drop in ABS, even before any visible crack was developed. Damage development and fracture behavior were then analyzed using scanning electron microscopy (SEM). The SEM analysis revealed that damage zones, not cracks, were initiated during the fatigue loading, and were the main cause of the toughness drop. Mechanisms for the damage initiation include matrix crazing and debonding of small rubber particles; however, large rubber particles remained intact. Based on the results, a deformation model is proposed for the damage zone initiation, which provides an explanation for the toughness change under the fatigue loading.