Effect of supports on the redox performance of pyrite cinder in chemical looping combustion

Chemical looping combustion (CLC) is a clean and efficient flame-free combustion technology,which combust the fuels by lattice oxygen from a solid oxygen carrier with inherent CO2 capture.The develop-ment of oxygen carriers with low cost and high redox performance is crucial to the whole efficiency of CLC process.As the solid by-product from the sulfuric acid production,pyrite cinder presented excellent redox performance as an oxygen carrier in CLC process.The main components in pyrite cinder are Fe2O3,CaSO4,Al2O3 and SiO2 in which Fe2O3 is the active component to provide lattice oxygen.In order to sys-tematic investigate the functions of supports (CaSO4,Al2O3 and SiO2) in pyrite cinder,three oxygen car-riers (Fe2O3-CaSO4,Fe2O3-Al2O3 and Fe2O3-SiO2) were prepared and evaluated in this study.The results showed that Fe2O3-CaSO4 displayed high redox activity and cycling stability in the multiple redox cycles.However,both Fe2O3-Al2O3 and Fe2O3-SiO2 experienced serious deactivation during redox reactions.It indicated that the inert Fe-Si solid solution (Fe2SiO4) was formed in the spent Fe2O3-SiO2 sample,which decreased the oxygen carrying capacity of this sample.The XPS results showed that the oxygen species on the surface of Fe2O3-CaSO4 could be fully recovered after the 20 redox cycles.It can be concluded that CaSO4 is the key to the high redox activity and cycling stability of pyrite cinder.     

Effects of Ultrasonic Vibration on Material Flow and Thermal Cycles in Friction Stir Welding of Dissimilar Al/Mg Alloys

Comparative experiments are performed in friction stir welding (FSW) of dissimilar Al/Mg alloys with and without assistance of ultrasonic vibration. Metallographic characterization of the welds at transverse cross sections reveals that ultrasonic vibration induces differences in plastic material flow in two conditions. In FSW, the plastic material in the peripheral area of shoulder-affected zone (SAZ) tends to flow downward because of the weakening of the driving force of the shoulder, and a plastic material insulation layer is formed at the SAZ edge. When ultrasonic vibration is exerted, the stirred zone is divided into the inner and outer shear layers, the downward material flow trend of the inner shear layer disappears and tends to flow upward, and the onion-ring structure caused by the swirl motion is avoided in the pin-affected zone. By improving the flow behavior of plastic materials in the stirred zone, ultrasonic vibration reduces the heat generation, accelerates the heat dissipation in nugget zone and changes the thermal cycles, thus inhibiting the formation of intermetallic compound layers.

     

在Fe-Al-C系统中合成优质Ⅱa型宝石级金刚石单晶

和优质Ib型宝石级金刚石单晶生长相比，作为当今高温高压晶体生长的一种高精尖技术，优质1／a型宝石级金刚石单晶对合成技术提出了更高更苛刻的要求：枢研究从晶体的生长速度出发，发现一开始阶段（大约几个小时）的晶体生长速度对优质宝石级金刚石单晶的后期生长争关重要。埘Fe-Al-C系统（Al含量不大于2．5wt％）来说，采用多品种法将晶体开始阶段的晶体生长速度由1．5mg／h降至0．5mg／h后，对生长过程中金属包裹体的进入有了明显的抑制作用，晶体的质量有了很大提高。从晶体中包裹体的存任形式来看，为了获得优质Ⅱa型宝石级金刚石单晶，在触媒中人为地添加除氮剂给晶体生长过程中的排杂过程带来了很大的难度：为了更好的实现排杂，必须很好的处理晶体表面的径向平铺生长速度和晶体轴向的堆积生长速度之间的火系。     

红外测温技术在离心复合铸造轧辊生产上的应用

本文分析了离心复合铸造轧辊生产过程中离心机停机温度和时间对轧辊质量的影响 ,提出了用先进的红外测温技术来预报停机温度和时间 ,以实现微机监控适时停机 ,保证轧辊内外层熔合良好 ;同时指出了红外测温技术在离心复合铸造轧辊生产上的应用前景     

Synthesis and characterization of mechanical-alloyed Ti–xMg alloys

The synthesis and characterization of Ti–xMg (x=4, 9, 12, 15, 21, 24 at%) alloys using mechanical alloying was investigated. A nanometer-sized Ti–24Mg alloy was produced. During mechanical alloying, the height of the XRD peaks of the Mg in the Ti–9Mg alloy decreased, and then disappeared, whereas the Ti XRD peaks broadened, and the grain size decreased with increasing milling time. The Mg firstly dissolved in the grain boundaries of the Ti, and then diffused into the Ti grain interiors. The grain boundaries played an important role in enhancing the solid solubility of Mg in Ti. With increasing Mg content the volume fraction of grain boundaries increased, and a decrease in grain size occurred after mechanical alloying for 48 h.     

LD7铝合金时效工艺的研究

通过试验系统地研究了ＬＤ７铝合金的单级和两级时效工艺。结果表明，与传统的单级时效相比，两级时效在不降低室温强度，硬度的前提下，可显著提高合金的电导率及高温性能。     

国产气相聚乙烯浆液催化剂的工业应用

本文简要阐述了北化院BCS01和上海院SLC-S两种国产气相聚乙烯浆液催化剂的性能、催化剂结构,在Unipol聚乙烯工业装置上应用结果,以及和进口同类催化剂UCAT-J的性能比较。     

扩链剂在PVC树脂生产中的应用

讨论了常见扩链剂的功能及在聚氯乙烯树脂生产中的应用。     

国产耐火材料在欧洲3 300t/d生产线上的整体配套

Fushe-Kruje水泥厂项目位于距阿尔巴尼亚首都地拉那市28公里处，是由黎巴嫩SEAMENT集团投资兴建的．是迄今阿尔巴尼亚最大的外商投资项目，设计能力为3300t/d新型干法水泥熟料生产线，是全套生产线由我公司设计、制造成套、施工、安装、调试及试生产的总承包项目。