Synthesis and characterization of cellulose nanowhisker-reinforced-poly(ε-caprolactone) scaffold for tissue-engineering applications

Poly(ε-caprolactone) (PCL) is a bioresorbable and biocompatible polymer with assorted medical applications. However, remarkable hydrophobicity and nonosteoconductivity have stood as a barrier to limit its applications. The present study aims to modify the bulk characteristics of PCL to develop a polymeric scaffold with adequate structural and mechanical properties to support regenerated tissues. For this purpose, functionalized bacterial cellulose nanowhiskers (BCNW-g-βCD-PCL₂₀₀₀) are synthesized. Reinforcing PCL matrix with 4 wt % of the nanowhiskers resulted in a bionanocomposite with promoted bulk properties. Compared to neat PCL, the obtained bionanocomposite shows improvements of 115 and 51% in tensile strength and Young's modulus, respectively; 20% increase in hydrophilicity; 7% increase in degradation rate; and 6% decrease in crystallinity. Gas foaming/combined particulate leaching technique is used to develop highly porous structures of 86–95% porosity with interconnected macropores of mean pore diameters of 250–420 μm. Porous scaffolds showed compression modulus values of 5.3–9.1 MPa and would have promising applications in regenerative medicine. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48481.     

Effective participation of wind turbines in frequency control of a two-area power system using coot optimization

In this paper, load frequency control is performed for a two-area power system incorporating a high penetration of renewable energy sources. A droop controller for a type 3 wind turbine is used to extract the stored kinetic energy from the rotating masses during sudden load disturbances. An auxiliary storage controller is applied to achieve effective frequency response. The coot optimization algorithm (COA) is applied to allocate the optimum parameters of the fractional-order proportional integral derivative (FOPID), droop and auxiliary storage controllers. The fitness function is represented by the summation of integral square deviations in tie line power, and Areas 1 and 2 frequency errors. The robustness of the COA is proven by comparing the results with benchmarked optimizers including: atomic orbital search, honey badger algorithm, water cycle algorithm and particle swarm optimization. Performance assessment is confirmed in the following four scenarios: (i) optimization while including PID controllers; (ii) optimization while including FOPID controllers; (iii) validation of COA results under various load disturbances; and (iv) validation of the proposed controllers under varying weather conditions.     

Synthesis and characterization of saturated and unsaturated copolyesters based on bis-1,4-(dicarboxymethoxy) benzene

Saturated copolyester were prepared by copolyesterification of bis-1,4-(dicarboxymethoxy) benzene and phthalic anhydride with diethylene glycol, triethylene glycol, tetraethylene glycol, 1,4-butane diol, 1,2-propane diol, and 1,6-hexamethylene glycol. Also, unsaturated copolyesters were prepared by copolyesterification of bis-1,4-(dicarboxymethoxy) benzene and maleic anhydride with the same glycols. All the copolyester resins obtained have been characterized and unsaturated copolyesters in the form of films were determined. IR and ¹H-NMR spectroscopy were used for both qualitative and quantitative analysis of the copolyesters resins and their hydrolyzate products, after curing with styrene. © 1992 John Wiley & Sons, Inc.     

Investigation of transport phenomena in a hybrid ion exchange-electrodialysis system for the removal of copper ions

Hybrid ion exchange electrodialysis processes allow the removal of metal ions from dilute waste liquids and the recovery of more concentrated solutions. The work reported here was aimed at investigating the two steps in the treatment process, namely, adsorption of metal ions onto the packed bed of resin and electromigration (i.e., the transport of these ions in the complex system under the applied electrical field). The case of copper sulfate was investigated. Dowex resins with a cross-linking degree of 2 and 8% were used. The flux of copper through the resin bed and the current efficiency for ion transfer to the cathode compartment were determined as a function of potential gradient and copper ionic fraction in the bed. Apparent diffusion coefficients of Cu²⁺ in the overall system were deduced from the experimental data.     

Structural material from waste plastic

In efforts to contribute to community development, particularly in the context of Egyptian communities, waste plastics materials were successfully recycled without the difficult task of separation and reused to economically produce new structural material. Recycling was performed by mixing molten waste plastics with sand to produce these new materials. Samples with different percentages of plastics and different particle sizes of sand were used in the process. Materials showed acceptable density and high compressive strength, which was shown to be at a maximum with contents of about 30–40% waste plastic. Furthermore, certain types of sand having different colors were used to produce attractive materials, suitable for decorative uses. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2543–2547, 2004     

Dynamic mechanical properties of agricultural residues‐filled polystyrene

Agricultural residues (cotton straw) were added as very small particles to polystyrene (PS) at different weight ratios by using a melt‐mixing technique. The dynamic mechanical tests were performed over a wide range of temperatures and frequencies by using an ARES rheometer (Rheometrics Scientific) operated in the dynamic mode. The dynamic mechanical properties in terms of the storage modulus (G′), loss modulus (G″), compliance moduli, loss tangent, and dynamic viscosity were studied and compared for PS and PS composite. The results showed that the dynamic mechanical moduli and viscosity were found to increase with the addition of cotton straw and rise further with its loading increasing. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 37–40, 2004     

Rheological and dielectrical characterization of melt mixed polycarbonate-multiwalled carbon nanotube composites

A series of composites of polycarbonate (PC) with 23 different contents of multiwalled carbon nanotubes (MWNT) was produced by melt mixing using the masterbatch dilution method. In dielectric measurements, AC conductivity and complex permittivity data obtained in the frequency range between 10⁻³ and 10⁷ Hz at room temperature indicated the electrical percolation threshold at about 1.0 wt%.

The dynamic mode melt rheological measurements for the same samples at eight temperatures between 170 and 280 °C showed a visible change in the frequency dependence of dynamic moduli and the absolute value of the complex viscosity |η*| particularly at low frequencies. In literature these changes are sometimes related to so called ‘percolation threshold concentration’. Applying this picture to our experimental data we have to assume that the percolation threshold is strongly dependent on the measurement temperature. It changes from about 5 to 0.5 wt% MWNT by increasing the measurement temperature from 170 to 280 °C, respectively. This temperature dependence cannot be explained by a classical liquid-solid transition but may be related to the existence of a combined nanotube-polymer network.     

Yield response of lentil to directly applied and residual phosphorus in a Mediterranean environment

The response of lentil grown under rainfed conditions to directly applied and residual phosphorus (P) was described by a modified Mitscherlich equation, accounting for the effects of rainfall on (1) potential yield, and (2) the availability of soil-P to the crop. The response of lentil yield to directly applied and residual P was studied in two-course cereal–lentil rotational trials under rainfed conditions in a Mediterranean-type environment. Cereal crops were grown at different P application rates during 4 growing seasons at 3 sites, representing different rainfall zones in northwest Syria. Lentil (Lens culinaris Med.) was grown during 4 seasons at the same sites, each lentil crop following a cereal crop. In 3 out of 4 lentil-growing seasons, additional P was applied to lentil in subplots to compare the residual and direct effects of P application. The initial contents of extractable soil-P (P-Olsen) were low at all sites, in the range of 2–5 ppm P. Under the conditions of the experiments, lentil appeared to benefit slightly more from P applied to the preceding wheat crop (residual P) than from directly applied P. It is shown that the modified Mitscherlich equation could be used as a basis for P fertilizer recommendations for rainfed farming. As for lentil, it was concluded that a single application of P to the wheat crop in a wheat/lentil rotation could reduce the cost of lentil production, without reducing lentil yield.     

Effect of solvents on radiation‐induced grafting of styrene onto fluorinated polymer films

The effect of solvents on radiation‐induced grafting of styrene onto commercial fluorinated polymer films such as poly(tetrafluoroethylene) (PTFE), poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) and poly(tetrafluoroethylene‐co‐perfluorovinyl ether) (PFA) was investigated by a simultaneous irradiation technique. Three solvents, ie methanol, benzene and dichloromethane, were used to dilute styrene under various irradiation doses, dose rates and monomer concentrations. The effect of addition of mineral and organic acids on the degree of grafting in the presence of the three solvents was also studied. The degree of grafting was found to be strongly dependent upon the type of solvent and composition of the monomer/solvent mixture. Dilution of styrene with dichloromethane in various grafting conditions was found to enhance dramatically the degree of grafting compared with other solvents, and the maximum degree of grafting was achieved at a monomer/solvent mixture having a composition of 60:40 (v/v). The formation of polystyrene grafts in the three fluorinated films was verified using FTIR spectrometry. © 2001 Society of Chemical Industry