Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Fractal dimension of the grain boundary fracture in creep-fracture of cobalt-based heat resistant alloys

The effects of grain boundary configuration and creep conditions on the fractal dimension of the grain boundary fracture (D _f) were investigated using commercial cobalt-based heat resistant alloys, namely, HS-21 and L-605 alloys. Creep-rupture experiments were carried out under the initial creep stresses of 19.6–176 MPa in the temperature range from 1089–1422 K in air. The value of D _f was larger in specimens with serrated grain boundaries than in those with straight grain boundaries in the HS-21 alloy under the same creep condition, and the difference in the value of D _f between these specimens was large in the scale range of the analysis which was less than about one grain boundary length. However, there was almost no difference in the value of D _f between the specimens with serrated grain boundaries and those with straight grain boundaries in the L-605 alloy, because there was no obvious difference in the microstructure between these specimens. The value of D _f increased with decreasing creep stress in the scale range of the fractal analysis larger than about one grain boundary length in both HS-21 and L-605 alloys, while the stress dependence of D _f was larger in the HS-21 alloy. The stress dependence of D _f was explained by the stress dependence on the number of grain boundary microcracks linked to the fracture surface. The value of D _f estimated in the scale range smaller than about one grain boundary length showed essentially no stress dependence in both L-605 and HS-21 alloys.     

Flexural properties of moldings of rigid polyurethane made by reaction injection molding

Flexural properties of moldings made by Reaction Injection Molding (RIM), which are structural foams consisting of high density skin and low density core, were investigated by three-point bending tests. Two failure modes were observed in bending tests of the moldings made by RIM, and they are classified as follows according to the density ratio of skin layer to core layer: the opposite side of the skin layer to which load was subjected failed by tensile stress: and the same side of the skin layer to which load was subjected failed by compressive stress, causing wrinkling or buckling. Then the conventional composite beam theory was applied to the former failure mode and Hoff s buckling theory to the latter, and equations were derived to predict the flexural properties of the structural foams, which involved buckling from the flexural properties of solid construction. In addition, it has been shown that there exists a density distribution that maximizes the flexural strength of the moldings made by RIM with a given overall density. The results obtained here should be useful to the optimum structural design of moldings made by RIM.     

Sensitivity of an anadically oxidized aluminium film on a surface acoustic wave sensor to humidity

The sensitivity, transient response and sensitivity mechanism of a surface acoustic wave humidity sensor using porous anodically oxidized aluminium (alumina) films as mechanical interfaces have been studied theoretically and experimentally. It is found that the sensitivity of alumina films of 1.0 μm thickness is -0.034 m/(s %RH) and is the same order as that of polyimide films. The transient response of alumina films to humidity is about one order faster than that of polyimide films. For the sensitivity mechanism, the phase-velocity change is attributed to the mechanical perturbation caused by the absorption of water molecules. The equivalent density change of alumina films between 0 and 100%RH is about 0.7%. In addition, the actual stiffness constants of alumina films are two orders less than those of bulk alumina.     

Preparation and performance of poly(vinyl butyral) membrane for ultrafiltration

Ultrafiltration membrane was prepared from poly(vinyl butyral). The effects of membrane thickness, polymer concentration, evaporation time, and evaporation temperature, etc., on the performance of the resulting membranes have been studied. Dimethylacetamide was used as a casting solvent. The membrane formed by casting the polymer from a 15 wt % solution and evaporation at 25°C for 30 s had a flux value of 250 cm³ / cm² h (4.8 kg/cm², 26°C) at 92.9% rejection level for dextran sodium sulfate (average mol. wt. 550,000) separation. © 1993 John Wiley & Sons, Inc.     

Effect of degree of polymerization on gelation and flow processability of poly(vinyl chloride)

The effect of degree of polymerization (DP) on the gelation and flow processability of poly(vinyl chloride) (PVC) was studied. Sheets with adjusted degree of gelation were prepared by rolling rigid pipe formulation suspension PVC compounds with DPs of 800, 1050 and 1300 by changing the milling temperature. Their degrees of gelation were measured with DSC and their capillary flow properties were measured with a capillary rheometer at 150, 170 and 190°C and the effect of DP on the relation between gelation and flow processabilities was studied. Because of the higher shearing heat during milling, the sample with the higher DP had a higher history temperature and thus tended to show a higher degree of gelation. The viscosity increased as the gelation increased. The dependency of viscosity on DP was higher at higher milling and extrusion temperatures and thus at a higher degree of gelation and a lower shear rate. This was assumed to be attributed to the more prominent uniform molecular flow as against the particle flow. The die swell increased with increasing the milling and extrusion temperatures and hence with increasing the gelation. A sample with a lower DP tended to show a larger die swell and this tendency was even more pronounced at the higher extrusion temperature. The melt fracture easily occurred when a sample with advanced gelation was extruded at low temperature. Whereas at low milling temperatures a sample with the lower DP showed a lower critical shear rate at onset of melt fracture, and thus easily generating melt fracture, at high milling temperatures it showed a higher critical shear rate and hence scarcely generated melt fracture. These experimental results were explained by the fact and concept that a sample with a lower DP shows a higher increase in the gelation during extrusion and/or the slighter feature of particle flow as against the uniform molecular flow at the same gelation level. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1915–1938, 2004     

Diel rhythms of calling behavior and pheromone production of oriental tobacco budworm moth,Helicoverpa assulta (Lepidoptera: Noctuidae)

Both calling behavior and titer of (Z)-9-hexadecenal (Z9-16: Al), the major sex pheromone component ofHelicoverpa assulta, in pheromone glands showed distinct diel periodicity, and these two were synchronous. Calling was most actively performed and the pheromone titer reached a maximum from 2 to 6 h after lights-off. During photophase, no calling was shown and only a relatively small amount of Z9-16:A1 was detected. However, there was a time lag of a few days between peak calling activity and maximum pheromone titer. The pheromone titer was maximal from age 1 day to age 5 days and thereafter decreased while calling was most actively performed after age 3 days. Titers of three minor components, hexadecenal, (Z)-11-hexadecenal, and (Z)-9-hexadecenyl acetate, showed similar daily fluctuation patterns to that of Z9-16:Al, but relative to the titer of Z9-16:Al, the titer of the two aldehyde components remained relatively constant whereas that ofZ9-16:Ac increased in the late scotophase.     

Development of an epileptic seizure prediction algorithm using R–R intervals with self-attentive autoencoder

Epilepsy is a neurological disorder that may affect the autonomic nervous system (ANS) from 15 to 20 min before seizure onset, and disturbances of ANS affect R–R intervals (RRI) on an electrocardiogram (ECG). This study aims to develop a machine learning algorithm for predicting focal epileptic seizures by monitoring R–R interval (RRI) data in real time. The developed algorithm adopts a self-attentive autoencoder (SA-AE), which is a neural network for time-series data. The results of applying the developed seizure prediction algorithm to clinical data demonstrated that it functioned well in most patients; however, false positives (FPs) occurred in specific participants. In a future work, we will investigate the causes of FPs and optimize the developing seizure prediction algorithm to further improve performance using newly added clinical data.

     

Building a speech recognition system with privacy identification information based on Google Voice for social robots

The Journal of Supercomputing - Currently, many smart speakers, even social robots, appear on the market to help people's lives become more convenient. Usually, people use smart speakers to...     

Thermal conductivity and phonon scattering mechanisms in La#x2212;x#x2212;x#x2212;xMxCuO4

The thermal conductivity of high density La_2–xM_xCuO₄ (M=Ba, Sr) sintered materials was measured between 15K and 150K for the various concentrations of Ba and the phonon thermal conductivity was analyzed comparing with that of Nd_2–xCe_xCuO₄. The pretty large value for pure La₂CuO₄ was drastically diminished by substituting La by a small amount of Ba atoms especially at low temperatures. It was found that a new type of the phonon scattering center such as a two-level tunneling must be taken account of in order to explain the observed reduction.