Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

A rate adaptive bit-loading algorithm for in-building power-line communications based on DMT-modulated systems

This paper deals with a variable rate discrete multitone modulation system for broadband power-line communications, based on the bit-loading algorithm proposed by Leke and Cioffi. In the proposed system a suitable least mean square channel estimator is considered, which is based on the insertion of a training sequence (TS). The proposed approach will be compared with the ideal channel estimates, showing its effectiveness. Moreover, different TS lengths will be compared. The system performance, expressed in terms of bit rate and bit-error rate, is derived by simulation with and without estimation errors. The propagation environment has been assumed as a frequency-selective multipath fading channel with additive colored Gaussian noise, according to the in-building networks model.     

Model Driven Architecture

Bei der Model Driven Architecture (MDA) bilden Modelle die zentralen Elemente des Softwareentwicklungsprozesses. Ziel ist es, plattformspezifische Modelle möglichst automatisiert aus plattformunabhängigen Modellen abzuleiten. Dadurch soll der Aufwand der Softwareentwicklung verringert und die Adaptierung an neue Technologien erleichtert werden.*Vorschläge an Prof. Dr. Frank Puppe oder Dieter Steinbauer Alle „Aktuellen Schlagwörter“ seit 1988 finden Sie unter: www.ai-wuerzburg.de/as     

Anodising potential influence on well-ordered nanostructures formed by anodisation of aluminium in sulphuric acid

High-density structures with relatively well-ordered nanopore arrays have been obtained by the self-ordering growth of nanopores occurring during anodisation of aluminium in sulphuric acid. The resulting array of well-ordered nanopores strongly depends on an applied voltage of anodising, temperature and a procedure of synthesis. Regular arranged hexagonal arrays on aluminium with a relatively uniform pore diameter, interpore distance, and depth of pores exceeding 90 μm, can be formed by the self-ordering two-step anodising at 1 °C. The interpore distance and the pore diameter were evaluated on anodised aluminium layers obtained at different cell potentials ranging from 15 to 25 V. The detailed analyses of their uniformity were performed from SEM images. The analysis of a pore arrangement defects was made from SEM top view images taken on samples anodised at various cell potentials. The defect maps, known as Delaunay triangulations, of the arrangement of about 1000 pores were constructed for different applied anodising potentials. The percentage of pores that are not six-fold coordinated by the neighbouring pores indicates the percentage of defected surface.     

Antimutagenic activity of natural phenolic compounds present in the common bean ( Phaseolus vulgaris ) against aflatoxin B 1

Polyphenols with antimutagenic and anticarcinogenic properties are present in fruits, vegetables and legumes. In this study, the Salmonella typhimurium tester strains TA98 and TA100 were used in the microsuspension assay to examine the antimutagenic effect of phenolic compounds extracted from the common bean (Phaseolus vulgaris) against mutagenicity induced by aflatoxin B 1 (AFB 1 ). A dose-response curve was constructed for AFB 1 ; from which a level of 40ng AFB 1 /tube was selected for all antimutagenicity assays. The AFB 1 and phenolic extract (PE) were not toxic to the bacteria at concentrations tested. In the case of PE, results were similar to the number of spontaneous revertants for TA98 and TA100. The inhibitory effect of PE against AFB 1 mutagenicity was dose-dependent at the lower concentrations tested (2.5, 5, 10, 12.5, 15 and 25 μg-equivalent ( + )-catechin/tube for TA98; 0.5, 1, 1.5, 2.5, 5, 10 and 25 μg-equivalent ( + )-catechin/ tube for TA100). Further, a two-stage incubation procedure was used to investigate the potential interaction between PE and AFB 1 . The greatest inhibitory effect of the PE on AFB 1 mutagenicity occurred when PE and AFB 1 were incubated together. When the bacteria were first incubated with PE followed by a second incubation with AFB 1 , lower inhibition was observed. Lower inhibition was also observed when the bacteria were first incubated with AFB 1 followed by a second incubation with PE. The results suggest that the mechanism of inhibition could involve the formation of a chemical complex between of PE and AFB 1 .     

Quantitative determination of non-defect unstable structures in PVC through selective nucleophilic substitution with C6H5SNa

Summary The nucleophilic substitution with C₆H₅SNa, at -30°C, is compared for five PVC samples with various contents of isotactic triads. The conversion curves consist of a very fast stage followed by a steady one. All the samples are found to behave in the same way except for the content of the structures involved in the fast period. This content is estimated by extrapolating the straight lines of the steady stages to zero time. The obtained values are found to be a linear function of the content of isotactic triads. The results, together with some earlier ones, allow for the content of the labile non-defect structures in PVC to be determined.     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.     

Modified determination of 2-thiobarbituric acid value in fats and oils

Several methods for the determination of TBA-value were compared with a new direct modification (omitting the previous distillation), using 1-butanol as the sole solvent. The absorbance is measured at 530 nm after heating to 95 degrees C for 120 min, and cooling. The effect of variables was tested by the Youdens ruggedness test (reaction time, temperature, cooling, concentration of sample, thiobarbituric acid, water, heavy metals, antioxidants, chelating agents, bubbling with oxygen or nitrogen). The Lambert-Beers law is valid in the absorbance range between 0.05 and 0.8. The repeatability is better than that of the Dzikowskis procedure and comparable with those of more complicated distillation methods. The standard deviation is in a linear relation with the absorbance (range 0.1-1.0). The method was found satisfactory for evaluating lard, cooking fat, soybean, sunflower, and rapeseed oils in the stage of beginning rancidity.