Proton conducting acid-base mixed materials under water-free condition

In recent years, a lot of attentions have been paid for a development of water-free polymer electrolyte membranes fuel cells (PEMFC) at intermediate temperatures (above 100 °C) because of many technological advantages of higher temperature operation. However, the proton conductivity of conventional polymer membranes under water-free condition is usually very low and the polymeric membranes are not stable at higher temperatures. So, the development of non-hydrous proton conducting membrane under water-free condition has been a state of the art issue in the advanced PEMFC technology. In this study, non-hydrous protonic conducting material was prepared by the mixing of acidic surfactant of mono-dodecylphosphate (MDP) and organic base of benzimidazole (BnIm). The proton conductivity and thermal stability of MDP-BnIm mixed material increased with the mixing ratio of BnIm. Maximum proton conductivity of MDP-BnIm mixed material (BnIm mixing ratio of 200 wt.%. vs. MDP) was found to be 1×10⁻³ S cm⁻¹ at 150 °C under water-free condition.     

Ru-catalyzed anode materials for direct hydrocarbon SOFCs

A solid oxide fuel cell using a thin ceria-based electrolyte film with a Ru-catalyzed anode was directly operated on hydrocarbons, including methane, ethane, and propane, at 600 °C. The role of the Ru catalyst in the anode reaction was to promote the reforming reaction of the unreacted hydrocarbons by the produced steam and CO₂, which avoided interference from steam and CO₂ in the gas-phase diffusion of the fuels. The resulting peak power density reached 750 mW cm⁻² with dry methane, which was comparable to the peak power density of 769 mW cm⁻² with wet (2.9 vol.% H₂O) hydrogen. More important was the fact that the cell performance was maintained at a high level regardless of the change in the methane utilization from 12 to 46% but was significantly reduced by increasing the hydrogen utilization from 13 to 42%. While the anodic reaction of hydrogen was controlled by the slow gas diffusion, the anodic reaction of methane was not subject to the onset of such a gas-diffusion process.     

Anionic polymerization of methyl methacrylate in the presence of chromium carbonyl [Cr(CO)6]

Summary The presence of Cr(CO)₆ in nBuLi-initiated anionic polymerization of methyl methacrylates (MMA) was found to effectively enhance stereoselectivity of the polymerization in toluene at 0°C. nBuLi/Cr(CO)₆ afforded an isotactic PMMA with 86 % of mm triad, and the polymers obtained with nBuLi/Cr(CO)₆/tBuOK were rich in heterotactic structures (mr = ca. 54%). In both cases, the selectivity was improved in ca. 10% compared to those of the polymerization conducted under the similar conditions without Cr(CO)₆. Received: 20 January 2003/Revised version: 21 April 2003/Accepted: 21 April 2003 Correspondence to Eiji Ihara     

Anatase Sol Prepared from Peroxotitanium Complex Aqueous Solution Containing Niobium or Vanadium

Niobium- or vanadium-doped anatase sols were prepared by hydrothermal treatment of 0.1 mol/dm³ peroxotitanium complex aqueous solutions dissolving 0–10 mol% niobium or vanadium at 100°C for 8 h. Niobium-doping caused the increase of lattice constants of anatase and the shape change of anatase crystal from spindle-like to cubic-like structure, but no change of the optical absorbance. Vanadium-doping caused the decrease of lattice constant of c -axis, the miniaturization of anatase crystal and the increase of optical absorbance at the wavelength from 350–700 nm.     

The effect of ionic cross-links on the deformation behavior of homoblends made of poly(styrene-co-styrenesulfonic acid) and poly(styrene-co-4-vinylpyridine)

Deformation behavior of stoichiometric blends made from poly(styrene-co-styrenesulfonic acid) (SPS) and poly(styrene-co-4-vinylpyridine) (SVP) was investigated by TEM observation of strained thin films. An FTIR investigation revealed that ionic cross-links were formed between the component polymers upon blending due to intermolecular ion-ion interactions, which arose from proton transfer from sulfonic acid groups to pyridine groups. TEM observations indicate that the deformation mode of the blends changed from crazing only to crazing plus shear deformation, with the shear contribution becoming larger, as the ion content in the blends increased. Such changes in deformation mode can be understood as arising from an increase in the ‘effective’ strand density due to the formation of ionic cross-links upon blending. It was also found that the ionic cross-links via pyridinium cation/sulfonate anion ion pairs were more effective in inducing the transition of deformation mode than ionic cross-links via -SO₃⁻/Na⁺ or -SO₃⁻/Ca²⁺ ion pairs.     

Diffusion process of amino acids in polymer supports for solid‐phase peptide synthesis as studied by pulsed‐field‐gradient spin‐echo proton nuclear magnetic resonance

The diffusion coefficient (D) values of tert‐butyloxycarbonyl‐glycine, tert‐butyloxycarbonyl‐L ‐tryptophan, tert‐butyloxycarbonyl‐L ‐phenylalanine (Boc‐Phe), and 9‐fluorenylmethoxycarbonyl‐L ‐phenylalanine in Merrifield polystyrene (MPS) gels, poly(ethylene glycol)‐grafted polystyrene (PEG–PS) gels, and crosslinked ethoxylate acrylate (CLEAR) gels, as used in solid‐phase peptide synthesis, were determined by the pulsed‐field‐gradient spin‐echo ¹H‐NMR method. From these experimental results, it was found that the amino acids in MPS gels, PEG–PS gels, and CLEAR gels with N,N‐dimethylformamide‐d₇ (DMF‐d₇) as a solvent had multidiffusion components within a measurement timescale of 10 ms. The D value of Boc‐Phe in polystyrene gels (1% divinylbenzene crosslinked) with tetrahydrofuran‐d₈ was much larger than that in the same gels with DMF‐d₇. Furthermore, the required time in which an amino acid transferred from a reactive site to a reactive site was estimated, within which the solvents and amino acids in the polymer supports diffused in the swollen beads.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 413–421, 2003     

Surface modification of contact lenses using adsorption of ethylene oxide branched copolymers

To examine methods for reducing the amount of adsorbed protein on the surface of contact lenses during use, cationic copolymers containing poly(ethylene oxide) units were synthesized and evaluated as surface modifiers. Poly(ethylene oxide) graft‐branched copolymers of composition 70 mol % dimethylaminoethyl methacrylate (DM) and 30 mol % methoxy polyethylene glycol methacrylate (Mp0G; p = 2, 4, 9; the average number of the ethylene oxide units) were obtained using nonionic monomers containing poly(ethylene oxide) units. The copolymers very efficiently prevented protein adsorption on a contact lens. Contact angle measurements showed that immersion in tear fluid made the lens surface hydrophobic because of adsorption of proteins with hydrophobic residues. The copolymer pretreatment made the lens surface hydrophilic, even after dipping in artificial tear fluid. These results suggest that adsorption of the poly(ethylene oxide) branched copolymer on the contact lens would make the lens surface hydrophilic and prevent protein adsorption. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Anatase-Type TiO2 and ZrO2-Doped TiO2 Directly Formed from Titanium(III) Sulfate Solution by Thermal Hydrolysis: Effect of the Presence of Ammonium Peroxodisulfate on their Formation and Properties

Anatase-type TiO₂ powder containing sulfur with absorption in the visible region was directly formed as particles with crystallite in the range 15–88 nm by thermal hydrolysis of titanium(III) sulfate (Ti₂(SO₄)₃) solution at 100°–240°C. Because of the presence of ammonium peroxodisulfate ((NH₄)₂S₂O₈), the yield of anatase-type TiO₂ from Ti₂(SO₄)₃ solution was accelerated, and anatase with fine crystallite was formed. Anatase-type TiO₂ doped with ZrO₂ up to 9.8 mol% was directly precipitated as nanometer-sized particles from the acidic precursor solutions of Ti₂(SO₄)₃ and zirconium sulfate in the presence and the absence of (NH₄)₂S₂O₈ by simultaneous hydrolysis under hydrothermal conditions at 200°C. By doping ZrO₂ into TiO₂ and with increasing ZrO₂ content, the crystallite size of anatase was decreased, and the anatase-to-rutile phase transformation was retarded as much as 200°C. The anatase-type structure of ZrO₂-doped TiO₂ was maintained after heating at 1000°C for 1 h. The favorable effect of doping ZrO₂ to anatase-type TiO₂ on the photocatalytic activity was observed.     

Scandium-Doped Anatase (TiO2) Nanoparticles Directly Formed by Hydrothermal Crystallization

Anatase-type TiO₂ solid solutions doped with 0–10 mol% scandium were formed by hydrothermal crystallization under weak basic conditions above 180°C for 5 h from amorphous co-precipitates that were obtained from the aqueous precursor solutions of TiOSO₄ and Sc(NO₃)₃ using aqueous ammonia. The anatase particles were spindle-like and consisted of nanosized-crystallites (23–25 nm). The lattice parameter c ₀ of anatase and the length and width of the spindle-like anatase gradually increased when the scandium content was increased. The diffuse reflectance spectra of the as-prepared TiO₂ doped with scandium showed that the onset of absorption slightly shifted to longer wavelengths with increasing scandium content. The band gap of anatase was slightly increased by making solid solutions with scandium oxide.     

The Role of a Nonribosomal Peptide Synthetase in l‐Lysine Lactamization During Capuramycin Biosynthesis

Capuramycins are one of several known classes of natural products that contain an l ‐Lys‐derived l ‐α‐amino‐?‐caprolactam (l ‐ACL) unit. The α‐amino group of l ‐ACL in a capuramycin is linked to an unsaturated hexuronic acid component through an amide bond that was previously shown to originate by an ATP‐independent enzymatic route. With the aid of a combined in vivo and in vitro approach, a predicted tridomain nonribosomal peptide synthetase CapU is functionally characterized here as the ATP‐dependent amide‐bond‐forming catalyst responsible for the biosynthesis of the remaining amide bond present in l ‐ACL. The results are consistent with the adenylation domain of CapU as the essential catalytic component for l ‐Lys activation and thioesterification of the adjacent thiolation domain. However, in contrast to expectations, lactamization does not require any additional domains or proteins and is likely a nonenzymatic event. The results set the stage for examining whether a similar NRPS‐mediated mechanism is employed in the biosynthesis of other l ‐ACL‐containing natural products and, just as intriguingly, how spontaneous lactamization is avoided in the numerous NRPS‐derived peptides that contain an unmodified l ‐Lys residue.