Inertia-friction welding of SiC-reinforced 8009 aluminium

Inertia-drive friction welding (IFRW) of an 8009 Al alloy (Al-8.5 Fe-1.7 Si-1.3 V, wt%) reinforced with 11 volume per cent SiC particles (8009/SiC/11_p) has been investigated. Inertia-drive friction welds were made with constant energy at two levels of axial force. The microstructures of the base material and the welds were characterized using optical and scanning electron microscopy, while the mechanical properties were evaluated using microhardness and tensile testing. Examination of weld sections revealed that the hot deformation experienced during welding produced a homogenized microstructure with a uniform distribution of SiC particles along the bond line. No evidence of a chemical reaction between the SiC and the matrix was found in any of the welds, but cracking of some of the larger SiC particles was observed in the base material as well as in the IFR welds. The average microhardness of the various heat-and-deformation affected zones (HDZs) of the welds did not vary greatly from that of the base material, and no weld induced weak regions were discerned. The room-temperature (RT) tensile strength of the IFR welds exceeded 90 per cent of the base material. The weld tensile specimens failed at the outer edge of the HDZ for all of the welds tested. The fracture surface of the 8009 matrix of tensile samples for both the base material and the welds exhibited a dimpled appearance indicating a ductile failure, while fracture through the SiC appeared to occur in a brittle fashion. IFRW has proven effective in joining 8009/SiC/11_p with little loss in RT hardness and tensile properties.     

Impact of uncertainties on estimations of heat pump cycle performance

Sensitivity analysis is used to show how uncertainties in basic factors, such as heat transfer, pressure drop, compressor efficiency, and thermophysical properties, influence the result of heat pump cycle performance estimations. By comparing the results of this analysis with uncertainty levels of estimations and experimental determinations, it is established to what extent improvements in accuracy are needed. The investigation was carried out for several different applications and, as working fluids, both pure substances and non-azeotropic mixtures were examined. It was found that evaporation heat transfer and compressor efficiency are two areas where improvements are needed. It is also shown that estimates using very accurate, substance-specific, equations of state differ from those using more general types by up to 1 % for COP and 2% for capacity.     

A semi-analytic boundary element method for parabolic problems

A new semi-analytic solution method is proposed for solving linear parabolic problems using the boundary element method. This method constructs a solution as an eigenfunction expansion using separation of variables. The eigenfunctions are determined using the dual reciprocity boundary element method. This separation of variables-dual reciprocity method (SOV-DRM) allows a solution to be determined without requiring either time-stepping or domain discretisation. The accuracy and computational efficiency of the SOV-DRM is found to improve as time increases. These properties make the SOV-DRM an attractive technique for solving parabolic problems.     

Evaluation of in vitro stability of large unilamellar liposomes coated with a modified polysaccharide (O-palmitoylpullulan)

Aiming at encapsulation of a hydrosoluble drug, large unilamellar liposomes (LUV) of egg phosphatidylcholine (PC) were coated with a natural polysaccharide derivative, O-palmitoylpullulan (OPP), and its in vitro stability evaluated using fluorescent probes. This coating (in OPP/PC weight ratio of 3) improved significantly the in vitro stability of LUV by decreasing both the permeability and fluidity of the liposomal membrane.This paper was accepted for publication after the 1995 Conference of the European Society of Biomaterials, Oporto, Portugal, 10–13 September.     

Sterilization of heparinized Cuprophan hemodialysis membranes

The effects of sterilization of dry heparinized Cuprophan hemodialysis membranes by means of ethylene oxide (EtO) exposure, gamma irradiation, or steam on the anticoagulant activity and chemical characteristics of immobilized heparin and the permeability of the membrane were investigated. Sterilization did not result in a release of heparin or heparin fragments from heparinized Cuprophan. Sterilization of heparinized Cuprophan by means of EtO exposure and gamma irradiation induced a slight, insignificant decrease of the anticoagulant activity. In contrast, steam-sterilized heparinized Cuprophan showed a higher anticoagulant activity than unsterilized heparinized Cuprophan, which was most likely caused by cleavage of some of the covalent bonds between heparin and Cupropha. The effects of sterilization on the permeability of unmodified Cuprophan and heparinized Cuprophan were compared. The permeability of unmodified Cuprophan for vitamin B₁₂ (Vit B₁₂) and sulfobromophthalein (SBP) was reduced by 20–35% after EtO exposure and gamma irradiation and was reduced by 90–95% after steam sterilization. The water permeability of unmodified Cuprophan remained the same after EtO exposure and gamma irradiation but also dramatically reduced after steam sterilization. These reductions were ascribed to the collapse of pores of the membrane. The permeability of heparinized Cuprophan was not affected by EtO exposure and gamma irradiation but dramatically reduced after steam sterilization, although to a lesser extent than in the case of unmodified Cuprophan. Apparently, the presence of immobilized heparin (partially) prevented the collapse of pores during sterilization. Gamma irradiation was recommended as the preferred method of sterilization for heparinized Cuprophan.     

INSTRUMENTATION FOR FLOW PROPERTIES OF GAS-SOLID SUSPENSIONS AND RECENT ADVANCES

Measurements of local velocity, density, and mass flow of phases of a gas-solid suspension are needed in determining transport properties, validating theoretical predictions, and formulating design procedures. Most of the available instruments are based on time averages or fluctuations with time. Primary standard for direct measurement of density of a phase such as solid particles is being developed. A laser phase Doppler device, within certain restrictions, may give local instantaneous density, while other optical methods and neutron beam remain secondary standards based on mass flow calibrations. An overall review including recent results has been made on both intrusive and non-intrusive instruments; their limitations and future possibilities are outlined and discussed. The limitations of the traditional approach utilizing the triangular relation between local averages of mass flow, velocity, and density of particles for the determination of flow properties, and higher order correlations are demonstrated.     

Advancing controlled release packaging through smart blending

Researchers from Rutgers University and Clemson University have collaborated to develop a concept of using smart blending to generate functional packaging films for the controlled release of active compounds such as antimicrobials, antioxidants and flavour compounds to extend the shelf‐life of food. In this paper, literature results are reviewed to justify the significance of controlled release packaging (CRP) and the research gaps for further development are identified. A major research gap is the lack of packaging materials that can provide the release of active compounds at rates suitable for a wide range of food packaging applications. Smart blending is a promising technology for bridging this research gap. To fully realize the potentials of smart blending, a systematic approach for developing CRP using smart blending is also presented. Copyright © 2005 John Wiley & Sons, Ltd.     

The Air is Always Cleaner on the Other Side: Race,Space, and Ambient Air Toxics Exposures in California

Abstract: Environmental justice advocates have recently focused attention on cumulative exposure in minority neighborhoods due to multiple sources of pollution. This article uses U.S. EPA's National Air Toxics Assessment (NATA) for 1996 to examine environmental inequality in California, a state that has been a recent innovator in environmental justice policy. We first estimate potential lifetime cancer risks from mobile and stationary sources. We then consider the distribution of these risks using both simple comparisons and a multivariate model in which we control for income, land use, and other explanatory factors, as well as spatial correlation. We find large racial disparities in California's “riskscape” as well as inequalities by other factors and suggest several implications for environmental and land use policy.     

Syntax and consistent equation semantics of hybrid Chi

The hybrid χ (Chi) formalism integrates concepts from dynamics and control theory with concepts from computer science, in particular from process algebra and hybrid automata. It integrates ease of modeling with a straightforward, structured operational semantics. Its ‘consistent equation semantics’ enforces state changes to be consistent with delay predicates, that combine the invariant and flow clauses of hybrid automata. Ease of modeling is ensured by means of the following concepts: (1) different classes of variables: discrete and continuous, of subclass jumping or non-jumping, and algebraic; (2) strong time determinism of alternative composition in combination with delayable guards; (3) integration of urgent and non-urgent actions; (4) differential algebraic equations as a process term as in mathematics; (5) steady-state initialization; and 6) several user-friendly syntactic extensions. Furthermore, the χ formalism incorporates several concepts for complex system specification: (1) process terms for scoping that integrate abstraction, local variables, local channels and local recursion definitions; (2) process definition and instantiation that enable process re-use, encapsulation, hierarchical and/or modular composition of processes; and (3) different interaction mechanisms: handshake synchronization and synchronous communication that allow interaction between processes without sharing variables, and shared variables that enable modular composition of continuous-time or hybrid processes. The syntax and semantics are illustrated using several examples.     

Guest Editors' Introduction: Machine Ethics

Machine ethics is concerned with how machines behave toward human users and other machines. It aims to create a machine that's guided by an acceptable ethical principle or set of principles in the decisions it makes about possible courses of action it could take. As ethics experts continue to progress toward consensus concerning the right way to behave in ethical dilemmas, the task for those working in machine ethics is to codify these insights. Eight articles in this special issue address the issues.This article is part of a special issue on Machine Ethics.