2D/3D Shaped Radiation Patterns of Sunflower and Conformal Antenna Arrays Using Phase Synthesis

2D and 3D beam synthesis from different antenna array arrangements are investigated in this paper. Planar sunflower, conformal cylinderical and spherical helical array arrangements are studied. The particle swarm optimization (PSO) technique is used to predict the phase distribution on the array elements. The beam synthesis is achieved by comparing the array factor with a predetermined mask with both upper and lower limits according to the intented application requirements. Different 2D and 3D masks are used in beam synthesis as pencil, flat-top, and cosecant single beam are predicted. The planar sunflower antenna array is investigated due to its high gain, low side-lobe level (SLL) below ??20 dB and its compact size. The phase distribution of sunflower array is estimated using PSO to radiate dual-beams in different planes. Dual-beam with pencil, flat-top, and cosecant beams are obtained with different half-power beam widths. 3D conformal antenna arrays of cylindrical and spherical helical arrangements are studied. Each 3D conformal array consists of four arms shifted in position by 90° orintation angle. Each arm is designed to radiate single beam in a specific direction. Four-beams are considered to radiate in the directions of θ_1,2,3,4?=?30°, and ?₁?=?0°, ?₂?=?90°, ?₃?=?180°, and ?₄?=?270° with SLL optimized below ??17 dB. The array arrangements analysis is based on the array theory formulation, through the implemention of the estimiated equation using a home programmed MATLAB code.

     

Function Follows Form: Correlation between the Growth and Local Emission of Perovskite Structures and the Performance of Solar Cells

Understanding the relationship between the growth and local emission of hybrid perovskite structures and the performance of the devices based on them demands attention. This study investigates the local structural and emission features of CH₃NH₃PbI₃, CH₃NH₃PbBr₃, and CH(NH₂)₂PbBr₃ perovskite films deposited under different yet optimized conditions using X‐ray scattering and cathodoluminescence spectroscopy, respectively. X‐ray scattering shows that a CH₃NH₃PbI₃ film involving spin coating of CH₃NH₃I instead of dipping is composed of perovskite structures exhibiting a preferred orientation with [202] direction perpendicular to the surface plane. The device based on the CH₃NH₃PbI₃ film composed of oriented crystals yields a relatively higher photovoltage. In the case of CH₃NH₃PbBr₃, while the crystallinity decreases when the HBr solution is used in a single‐step method, the photovoltage enhancement from 1.1 to 1.46 V seems largely stemming from the morphological improvements, i.e., a better connection between the crystallites due to a higher nucleation density. Furthermore, a high photovoltage of 1.47 V obtained from CH(NH₂)₂PbBr₃ devices could be attributed to the formation of perovskite films displaying uniform cathodoluminescence emission. The comparative analysis of the local structural, morphological, and emission characteristics of the different perovskite films supports the higher photovoltage yielded by the relatively better performing devices.     

An alternative clustering approach for reconstructing cross cut shredded text documents

In this paper, we propose a clustering approach for solving the problem of reconstructing cross-cut shredded documents. This problem is important in the field of forensic science. Unlike other clustering approaches which are applied as a preprocessing step before the actual reconstruction algorithms, our clustering approach is part of the reconstruction process itself. We define a new cost function which mainly relies on black pixels to measure the cost of pairing two shreds together. The reconstruction algorithm creates multiple clusters which grow by adding additional shreds based on the cost function. Adding a shred may result in merging two or more clusters to produce a larger cluster. We, also, propose a way to involve the user in the reconstruction process. We compare our approach with a recent proposal and conclude that our approach gives better solutions in less time.     

Organic geochemistry characterisation of crude oils from Mishrif reservoir rocks in the southern Mesopotamian Basin,South Iraq: Implication for source input and paleoenvironmental conditions

Seven crude oils from Cretaceous Mishrif reservoir rocks in the southern Mesopotamian Basin, South Iraq were studied to describe oil characteristics, providing information on the source of organic matter input and the genetic link between oils and their potential source rock in the basin. This study is based on biomarker and non-biomarker analyses performed on oil samples. The analysed oils are aromatic intermediate oils as indicated by high aromatic hydrocarbon fractions with more that 50%. These oils are also characterized by high sulfur and trace metal (Ni, V) contents and relatively low API gravity values (19.0–27.2° API). The results of this study indicate that these oils were derived from a marine carbonate source rocks bearing Type II-S kerogen that were deposited under sulphate-reducing conditions. This is primary achieved from their biomarkers and bulk carbon isotope and inorganic element contents (i.e., S, Ni and V). The absence of 18a (H)-oleanane biomarker also suggests a source age older than Late Cretaceous. The biomarker characteristics of these oils are consistent with those of the Late Jurassic to Early Cretaceous source rocks in the basin. However, biomarker maturity data also indicate that the oils were generated from early maturity source rocks. This appears to result from the type of kerogen of the source rock, characterized by a high-S kerogen (Type II-S).     

Vipulanandan model for the rheological properties with ultimate shear stress of oil well cement modified with nanoclay

In this study, the effect of clay nanoparticles (NC) and temperature on the rheological properties with ultimate shear stress and weight loss of the oil well cement (class H) modified with NC was investigated. The NC content was varied between 0 and 1% by the weight of the cement. The total weight loss at 800 °C for the oil well cement decreased from 6.10% to 1.03%, a 83% reduction when the cement was mixed with 1% of NC. The results also showed that 1% of NC increased the rheological properties of the cement slurry. The NC modification increased the yield stress (τ_o) and plastic viscosity (PV) by 5%–65% and 3%–16% respectively based on the NC content and the temperature of the cement slurry. The shear thinning behavior of the cement slurry with and without NC has been quantified using the Vipulanandan rheological model and compared with the Herschel-Bulkley model. The Vipulanandan rheological model has a maximum shear stress limit were as the Herschel-Bulkley model did not have a limit on the maximum shear stress. Based on the Vipulanandan rheological model the maximum shear stress produced by the 0% and 1% of NC at the temperature of 25 °C were 102 Pa and 117 Pa respectively hence an increase of 15% in the ultimate shear stress due to the addition of NC. The addition of 1% of NC increased the compressive strength of the cement by 12% and 43% after 1 day and 28 days of curing respectively. The modulus of elasticity of the cement increased with the additional of 1% NC by 6% and 76% after 1 day and 28 days of curing respectively. Effects of NC content and the temperature on the model parameters have been quantified using a nonlinear model (NLM). The NLM quantified the effect of NC treatment on all the model parameters.     

Treatment and restoration of used Mineral-Oil-Based hydraulic fluids from different machines. Part 1: Dewatering,filtration and effect of viscosity modifier

In this work, characterization and treatment of used hydraulic oil samples were performed in three steps. In the first step, the physical and the chemical properties of fresh and used hydraulic mineral oil samples from various centrifugal casting and pipe drawing machines were investigated according to ASTM D 6158. Results show that water content, solid particles count and depletion of additives have considerably affected most of the oil properties. Used oil samples failed in the appearance, thermal stability, oxidation stability, foaming tendency, water content and particles count.

In the second step, a simple methodology for dewatering and filtration was adopted. This methodology involved settling, followed by dry-air bubbling for oil dehydration and finally vacuum filtration. Such process successfully removed considerable portion of solid particles and water in used oil samples. Appearance, pour point, water content, particles count, and acid number were restored to the allowable limits. While water separability, oxidation stability, thermal stability and foaming tendency still failed the limits after treatment. It is obvious that additives will be needed to restore the latter properties.

In the third step, viscosity modifier additive was added to the oil samples to enhance viscous properties. A linear increase in kinematic viscosity was witnessed at 100°C, while at 40°C, an initial linear increase at low viscosities was followed by lower slopes at higher viscosities.     

Phase Inversion Strategy to Flexible Freestanding Electrode: Critical Coupling of Binders and Electrolytes for High Performance Li–S Battery

Development of flexible and freestanding electrode is attracting great attention in lithium–sulfur (Li–S) batteries, but the severe capacity fading caused by the lithium polysulfides (PSs) shuttle effect remains challenging. Herein, a completely new polymeric binder of polyethersulfone is introduced. Not only it enables massive production of flexible/current‐free electrode by a novel concept of “phase‐inversion” approach but also the resultant polymeric networks can effectively trap the soluble polysulfides within the electrode, owing to the higher hydrophilicity and stronger affinity properties than the routine polyvinylidene fluoride. Coupling with polysulfide‐based electrolyte, the Li–S cell shows a higher capacity of 1141 mAh g^?1, a lower polarization of 192 mV, and a more stable capacity retention with 100% Coulombic efficiency over 100 cycles at 0.25C. The advantages of favored binder and electrolyte are further demonstrated in lithium‐ion sulfur full battery with lithiated graphite anode, which demonstrates much improved performance than those previously reported. This work not only introduces a novel strategy for flexible freestanding electrodes but also enlightens the importance of coupling electrodes and electrolytes to higher performances for Li–S battery.     

A Dual-Band Printed Antenna Design Based on Annular Koch Snowflake Slot Structure

Wireless Personal Communications - The design of a fractal based slot antenna, to serve the dual-band communication applications, is proposed in this paper. The structure of the proposed antenna is...     

A novel energy‐aware routing mechanism for SDN‐enabled WSAN

Energy consumption is one of the most important design constraints when building a wireless sensor and actuator network since each device in the network has a limited battery capacity, and prolonging the lifetime of the network depends on saving energy. Overcoming this challenge requires a smart and reconfigurable network energy management strategy. The Software‐Defined Networking (SDN) paradigm aims at building a flexible and dynamic network structure, especially in wireless sensor networks. In this study, we propose an SDN‐enabled wireless sensor and actuator network architecture that has a new routing discovery mechanism. To build a flexible and energy‐efficient network structure, a new routing decision approach that uses a fuzzy‐based Dijkstra's algorithm is developed in the study. The proposed architecture can change the existing path during data transmission, which is the key property of our model and is achieved through the adoption of the SDN approach. All the components and algorithms of the proposed system are modeled and simulated using the Riverbed Modeler software for more realistic performance evaluation. The results indicate that the proposed SDN‐enabled structure with fuzzy‐based Dijkstra's algorithm outperforms the one using the regular Dijkstra's and the ZigBee‐based counterpart, in terms of the energy consumption ratio, and the proposed architecture can provide an effective cluster routing while prolonging the network lifetime.     

Tubular guidance systems for daylight: Achieved and predicted installation performances

Tubular daylight-guidance systems are linear devices that channel daylight into the core of a building. The development, over the last decade, of materials with high specular reflectance has led to a large number of passive zenithal systems; the most commercially successful type of daylight guidance being installed in many parts of the world. The rapid change in technology has not been matched by the development of either reliable and standardised design methods or design criteria against which the systems may be evaluated. This paper presents the results of several surveys of daylight guidance systems in 13 working buildings. These give an indication of the conditions created, which are used as the bases of suggested design criteria. A critical review of existing performance prediction methods notes that these lag far behind comparable methods for electric lighting and conventional glazing. A number of improved methods of prediction, currently under consideration by the CIE Technical Committee TC3-38, are presented and each is tested against measured data from the installation surveys.